2.5.2 - Force10 Networks

More documents

Recommendations

Info

Showing Network Settings Execute the show interface managementethernet command from either the User Exec or Privileged Exec modes. The resulting display, as shown in the example below, displays all the settings relating to IP-based management connections to the switch. The data includes the management IP address, subnet mask, default gateway, MAC information, etc., as shown below: Figure 7 Using the show network Command to Display Network Settings For details on setting up the management address, see Setting the Management IP Address on page 47. See also Setting up a Management Connection to the Switch on page 36. . Force10 #show interface managementethernet IP Address..................................... 10.10.1.151 Subnet Mask.................................... 255.255.255.0 Default Gateway................................ 10.10.1.254 Burned In MAC Address.......................... 00:01:E8:D5:A0:39 Locally Administered MAC Address............... 00:00:00:00:00:00 MAC Address Type............................... Burned In Network Configuration Protocol Current......... None Management VLAN ID............................. 1 Web Mode....................................... Enable Java Mode...................................... Disable Note: SFTOS v. 2.3 replaced the show network command with show interface managementethernet. 42 Getting Started
Displaying Supported Features and System Up-time The following is an example of using show version to display all supported features and system up-time: Force10 #show version Switch: 1 System Description............................. Force10 S50 Vendor ID...................................... 07 Plant ID....................................... 01 Country Code................................... 04 Date Code...................................... 062005 Serial Number.................................. DE4000126 Part Number.................................... 759-00001-00 Revision....................................... 0A Catalog Number................................. SA-01-GE-48T Burned In MAC Address.......................... 0001.E8D5.A151 Software Version............................... 2.2.1 Additional Packages............................ Force10 QOS Force10 Stacking 10/100 Ethernet/802.3 interface(s)............. 0 Gig Ethernet/802.3 interface(s)................ 2 10Gig Ethernet/802.3 interface(s).............. 0 Virtual Ethernet/802.3 interface(s)............ 0 System Name.................................... System Location................................ System Contact................................. System Object ID............................... force10 System Up Time................................. 1 days 22 hrs 55 mins 34 secs MIBs Supported: RFC 1907 - SNMPv2-MIB The MIB module for SNMPv2 entities RFC 2819 - RMON-MIB Remote Network Monitoring Management Information Base FORCE10-REF-MIB Force10 Reference MIB SNMP-COMMUNITY-MIB This MIB module defines objects to help support coexistence between SNMPv1, SNMPv2, and SNMPv3. SNMP-FRAMEWORK-MIB The SNMP Management Architecture MIB SNMP-MPD-MIB The MIB for Message Processing and Dispatching SNMP-NOTIFICATION-MIB The Notification MIB Module SNMP-TARGET-MIB The Target MIB Module SNMP-USER-BASED-SM-MIB The management information definitions for the SNMP User-based Security Model. SNMP-VIEW-BASED-ACM-MIB The management information definitions for the View-based Access Control Model for SNMP. USM-TARGET-TAG-MIB SNMP Research, Inc. F10OS-POWER-ETHERNET-MIB F10OS Power Ethernet Extensions MIB POWER-ETHERNET-MIB Power Ethernet MIB LAG-MIB The Link Aggregation module for managing IEEE 802.3ad RFC 1213 - RFC1213-MIB Management Information Base for Network Management of TCP/IP-based internets: MIB-II RFC 1493 - BRIDGE-MIB Definitions of Managed Objects for Bridges (dot1d) RFC 2674 - P-BRIDGE-MIB The Bridge MIB Extension module for managing Priority and Multicast Filtering, defined by IEEE 802.1D-1998. RFC 2674 - Q-BRIDGE-MIB The VLAN Bridge MIB module for managing Virtual Bridged Local Area Networks RFC 2737 - ENTITY-MIB Entity MIB (Version 2) RFC 2863 - IF-MIB The Interfaces Group MIB using SMIv2 RFC 3635 - Etherlike-MIB Definitions of Managed Objects for the Ethernet-like Interface Types F10OS-SWITCHING-MIB F10OS Switching - Layer 2 F10OS-INVENTORY-MIB F10OS Unit and Slot configuration. F10OS-PORTSECURITY-PRIVATE-MIB Port Security MIB. --More-- or (q)uit Figure 8 Displaying All Supported Features and System Uptime SFTOS Configuration Guide, Version 2.5.2.0 43
Page 1 and 2: SFTOS Configuration Guide Version 2
Page 3 and 4: SFTOS 2.5.2 adds: • A substantial
Page 5 and 6: Contents New Features . . . . . . .
Page 7 and 8: Chapter 3 Management . . . . . . .
Page 9 and 10: Chapter 9 Spanning Tree . . . . . .
Page 11 and 12: Configuring a Native VLAN . . . . .
Page 13 and 14: List of Figures Figure 1 Using the
Page 15 and 16: Figure 77 Using the show interface
Page 17 and 18: Figure 158 Using the access-list Co
Page 19: Figure 243 Configuring VLANs for OS
Page 22 and 23: Audience This document is intended
Page 24 and 25: Technical Support The iSupport Webs
Page 26 and 27: 26 About this Guide
Page 28 and 29: — Flow Control at the MAC layer:
Page 30 and 31: • HTML-based Management • HTTPS
Page 32 and 33: (Force10 S50) #show port 1/0/2 Figu
Page 34 and 35: 34 SFTOS Features
Page 36 and 37: Setting up a Management Connection
Page 38 and 39: Step Task (continued) 5 Enter Line
Page 40 and 41: Getting Help From the CLI The follo
Page 44 and 45: Displaying Statistics Privileged Ex
Page 46 and 47: Force10 (Config)#users snmpv3 acces
Page 48 and 49: Enabling Telnet to the Switch Acces
Page 50 and 51: • Enabling Spanning Tree Protocol
Page 52 and 53: The S-Series switch contains severa
Page 54 and 55: Downloading a Software Image After
Page 56 and 57: 5. After the transfer is complete,
Page 58 and 59: An alternative is to use the copy c
Page 60 and 61: Note that the association of a part
Page 62 and 63: After installing SFTOS 2.5.1 on the
Page 64 and 65: When converting from a Routing imag
Page 66 and 67: Saving the Startup Configuration to
Page 68 and 69: Chapter 5, Stacking S-Series Switch
Page 70 and 71: Uploading a Configuration Script to
Page 72 and 73: Troubleshooting a Downloaded Script
Page 74 and 75: Listing Configuration Scripts The s
Page 76 and 77: Changing the Management VLAN from t
Page 78 and 79: Setting the Host Name Prompt If you
Page 80 and 81: Setting up SNMP Management Simple N
Page 82 and 83: Commands to [disable] enable traps
Page 84 and 85: RMON is an extension of SNMP, and r
Page 86 and 87: Figure 47 RMON Event Thresholds Fig
Page 88 and 89: The software clock runs only when t
Page 90 and 91: Example #5: show sntp server Force1
Page 92 and 93:
• logging history. See Configurin
Page 94 and 95:
Interpreting system log messages Ta
Page 96 and 97:
Displaying the SNMP Trap Log The sh
Page 98 and 99:
Force10 #config Force10 (Config)#lo
Page 100 and 101:
100 System Logs
Page 102 and 103:
• The S50N, S50V, and S25P models
Page 104 and 105:
Management Unit Selection Algorithm
Page 106 and 107:
All of the forwarding protocols run
Page 108 and 109:
Use the member unit switchindex com
Page 110 and 111:
Setting Management Unit Preferences
Page 112 and 113:
Hardware Management Preference The
Page 114 and 115:
Notice, in Figure 67, that show swi
Page 116 and 117:
Using show Commands for Stacking In
Page 118 and 119:
The show stack command shows pretty
Page 120 and 121:
Table 3 Interfaces in the S-Series
Page 122 and 123:
Force10 #show interface 1/0/1 Ports
Page 124 and 125:
Use the show interface ethernet uni
Page 126 and 127:
Physical interfaces can become part
Page 128 and 129:
Enabling an Interface Ports are shu
Page 130 and 131:
The following table describes the e
Page 132 and 133:
If you connect powered devices to a
Page 134 and 135:
Bulk Configuration Bulk configurati
Page 136 and 137:
136 Configuring Interfaces
Page 138 and 139:
Table 6 describes the messages that
Page 140 and 141:
Verifying the DHCP Server Configura
Page 142 and 143:
Configuration Example — DHCP Serv
Page 144 and 145:
Step Command Syntax 2 authenticatio
Page 146 and 147:
Command Syntax Command Mode Purpose
Page 148 and 149:
Force10 #config Force10 (Config)# F
Page 150 and 151:
The scripts provided use OpenSSH (h
Page 152 and 153:
3. Use the show logging command to
Page 154 and 155:
Spanning Tree Protocol (STP, IEEE 8
Page 156 and 157:
Port States RSTP merges states from
Page 158 and 159:
MSTP CLI Management SFTOS supports
Page 160 and 161:
Enabling STP Use the following comm
Page 162 and 163:
The following commands influence wh
Page 164 and 165:
MSTP Configuration Example The foll
Page 166 and 167:
Use the show spanning-tree interfac
Page 168 and 169:
Figure 119 displays the output from
Page 170 and 171:
Figure 123 shows the output of the
Page 172 and 173:
172 Spanning Tree
Page 174 and 175:
• Static configuration is used wh
Page 176 and 177:
Link Aggregation Group (LAG) Comman
Page 178 and 179:
Interface Config mode commands Note
Page 180 and 181:
Basic LAG configuration example Thi
Page 182 and 183:
Using the Interface Range mode If y
Page 184 and 185:
Verify the status of the LAG as dyn
Page 186 and 187:
• Edge device: An edge device han
Page 188 and 189:
Deploying DiffServ The four basic s
Page 190 and 191:
Creating a Policy-Map The second st
Page 192 and 193:
Example (per interface): Force10 #c
Page 194 and 195:
Force10 #show class-map Class Class
Page 196 and 197:
Conform Secondary CoS—The action
Page 198 and 199:
The following is sample output from
Page 200 and 201:
VLAN 10: Finance Layer 3 Switch Por
Page 202 and 203:
Configuring Differentiated Services
Page 204 and 205:
204 Quality of Service
Page 206 and 207:
Note that the order of the rules is
Page 208 and 209:
— show mac access-lists Force10 #
Page 210 and 211:
Protecting the Management Interface
Page 212 and 213:
• An ACL applied to loopback inte
Page 214 and 215:
Use the show storm-control command
Page 216 and 217:
A VLAN is a set of end stations and
Page 218 and 219:
Executing the interface vlan 2-4094
Page 220 and 221:
Example of creating a VLAN and assi
Page 222 and 223:
3. Create VLAN 4 on switch R3 and a
Page 224 and 225:
Example of adding a LAG to a VLAN F
Page 226 and 227:
Example of creating a routed VLAN o
Page 228 and 229:
GARP Timers The following are GARP
Page 230 and 231:
1. Name switch R1, enable GVRP glob
Page 232 and 233:
Configuring a Private Edge VLAN (PV
Page 234 and 235:
Two commands can configure a native
Page 236 and 237:
Figure 186 Validating a Tagged Inte
Page 238 and 239:
. Force10 #show interface ethernet
Page 240 and 241:
DVLAN configuration example The exa
Page 242 and 243:
Configure switch R7: !---------Trun
Page 244 and 245:
Using the show vlan id vlan-id comm
Page 246 and 247:
set igmp maxresponse 1-3599 (typica
Page 248 and 249:
Use the show ip igmp interface unit
Page 250 and 251:
Port Mirroring Commands The followi
Page 252 and 253:
Stopping the mirroring session and
Page 254 and 255:
254 Port Mirroring
Page 256 and 257:
Enabling Routing The S-Series alway
Page 258 and 259:
Port Routing Configuration Example
Page 260 and 261:
IGMP Proxy Configuration The follow
Page 262 and 263:
Verifying the configuration Verify
Page 264 and 265:
RIP Configuration Example The confi
Page 266 and 267:
Border Router Port 0/2 192.150.2.1
Page 268 and 269:
Configuring OSPF on an S-Series ope
Page 270 and 271:
VLAN Routing This section introduce
Page 272 and 273:
3. As above, enable routing on R2:
Page 274 and 275:
5. Execute the show ip ospf command
Page 276 and 277:
1. As done previously, create the V
Page 278 and 279:
3. Use the show vlan id, show ip in
Page 280 and 281:
Port 0/2 192.150.2.1/24 Virtual Rou
Page 282 and 283:
3. Configure the IP address and sub
Page 284 and 285:
Note: In SFTOS 2.3.1.9, these messa
Page 286 and 287:
In addition to issuing the show swi
Page 288 and 289:
Monitoring SFPs The four fiber port
Page 290 and 291:
packets can be routed by the hardwa
Page 292 and 293:
• What was the LED status? (If th
Page 294 and 295:
294 • GVRP — Dynamic VLAN Regis
Page 296 and 297:
296 QoS • RFC 2474 — Definition
Page 298 and 299:
MIBs 298 • RFC 2096: IP forwardin
Page 300 and 301:
300 Force 10 MIBs You can see this
Page 302 and 303:
302
Page 304 and 305:
configuration, restore to factory d
Page 306 and 307:
inlinepower threshold command 132 i
Page 308 and 309:
MIBs, supported industry 298 mirror
Page 310 and 311:
RFC 3768 279 RFC 768 28, 294 RFC 78
Page 312 and 313:
show stack-port command 103 show st
Page 314:
VoIP support 202 VRID 281 VRRP 279
show all

2.5.2 - Force10 Networks

Create successful ePaper yourself

Delete template?

Save as template?