Blind actuator 1-gang flush-mounted Order-No. 2165 00 - Gira

More documents

Recommendations

Info

Software specification 4 Software description 4.1 Software specification ETS search paths: shutter / shutter / Blind actuator 1-gang flush-mounted BAU used: ASIC FZE 1066 + µC KNX/EIB type class: Device with cert. Physical layer + stack Configuration: S-mode standard PEI type: "00" Hex / "0" Dec PEI connector: No connector Application programs: No. Short description Name Version from mask version 1 Multifunctional shutter/blind application. Additional comprehensive extension function. Venetian blind, input 20BD11 1.1 for ETS3.0d onwards 705 Order-No. 2165 00 Page 14 of 149
4.2 Software "Venetian blind, input 20BD11" 4.2.1 Scope of functions Software "Venetian blind, input 20BD11" Scope of functions General - 1 x relay output (O1) to control a Venetian blind, roller shutter, awning or venting louver (mechanical locking of the running directions). - 3 x extension inputs for potential-free contacts. - No additional power supply required. The device electronics are supplied fully from the bus line. - Actively transmitting feedback or status messages of the output can be delayed globally after bus voltage return or after ETS programming. - The delay after bus voltage return can also be set generally for the inputs. - Effect of the extension inputs can be configured: either internal effect of I1 and I2 on the Venetian blind output (O1) and I3 on the bus or, alternatively, all three inputs separately on the bus. - Debounce time and telegram rate limit can be configured for the extension inputs. Blind output (O1) - Operating mode configurable: control of blinds with slats, shutters, awnings or venting louvers. - Separately configurable blind travelling times with travelling time extension for moves into the upper end position. - For blinds with slats, a slat moving time can be independently configured - Travel direction change-over time and the times for short and long-time operation (Step, Move) presettable. - Blind or slat position feedback telegram. In addition, an invalid blind position or an invalid travel movement can be reported back. Active (transmitting after changes or cyclically to the bus) or passive (object readout) feedback functions. - Assigning of outputs to up to 5 different safety functions (3 wind alarms, 1 rain alarm, 1 frost alarm) optionally with cyclical monitoring. - An extensive sun protection function with fixed and variable blind or slat positions at the beginning and at the end of the function can be activated separately for each output. Dynamic slat offset for slatted blinds included. Also with extended sun protection feature for integration into sophisticated shading control programs (operated via separate automatic and disabling object). Optionally also with automatic heating/cooling and presence detection function. - Forced position function can be implemented. - Up to 8 internal scenes configurable. Extension inputs (I1, I2, I3) - With separate impact on bus: Free allocation of the functions switching, dimming, Venetian blind and value encoder. - Disable object for disabling individual inputs (polarity of the disable object is adjustable). - Behaviour on bus voltage return can be configured separately for each input. - Scope of detail for the "Switching" function: Two independent switching objects available for each input (switching commands can be configured individually). Command can be set independently for rising and falling flank (ON, OFF, TOGGLE, no reaction). Independent cylical transmission of the switching objects can be selected depending on the flank or depending on the object value. - Scope of detail for the "Dimming" function: Single-surface and double-surface operation possible. Time between dimming and switching and dimming increments is adjustable. Telegram repetition and stop telegram transmission possible. Order-No. 2165 00 Page 15 of 149
Page 1 and 2: KNX/EIB Product documentation Issue
Page 3 and 4: Product definition 1 Product defini
Page 5 and 6: Installation, electrical connection
Page 13: Technical data 3 Technical data Gen
Page 17 and 18: Software "Venetian blind, input 20B
Page 29 and 30: 4.2.4.3 Channel-orientated function
Page 37 and 38: 4.2.4.4 Channel-oriented functions
Page 65 and 66:
Software "Venetian blind, input 20B
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
- II. Sun protection with shading c
Page 81 and 82:
Page 83 and 84:
4.2.4.4.6 Settings for automatic he
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
4.2.4.5 Priorities for the output S
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Priority of sun protection with res
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Delay scene recall ? Yes No Softwar
Page 147 and 148:
Forced position on, lowering / clos
Page 149:
Appendix Gira Giersiepen GmbH & Co.
show all

Blind actuator 1-gang flush-mounted Order-No. 2165 00 - Gira

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?