Blind actuator 1-gang flush-mounted Order-No. 2165 00 - Gira

More documents

Recommendations

Info

Software "Venetian blind, input 20BD11" Scope of functions - Scope of detail for the "Venetian blind" function: Command can be set independently for rising flank (no function, UP, DOWN, TOGGLE). Operation concept configurable (short – long – short or long – short). Time adjustable between short-time and long-time operation (only for short – long – short) Adjustable slat adjustment time (time during which a MOVE command can be terminated by releasing a pushbutton on the input). - Scope of detail for the "Value encoder" function: Flank (pushbutton as NO contact, pushbutton as NC contact, switch) and value for flank can be configured. Value adjustment for pushbutton long key-press possible for value encoder. For light scene extension with memory function, the scene can also be saved without prior recall. Order-No. 2165 00 Page 16 of 149
Software "Venetian blind, input 20BD11" Software information 4.2.2 Software information ETS project design and commissioning For configuration and commissioning of this device, it is necessary to use ETS3.0 from version "d" onwards. Advantages with regard to downloading (significantly shorter loading times) and parameter programming can be expected only if this ETS patch version or later versions are used. The advantages are gained through the use of the mask version 7.5. The product database required for the ETS3.0 from version "d" or more recent versions is offered in the *.VD4 format. The corresponding application program has the version number "1.1". Safe-state mode If the device - for instance as a result of errors in the configuration or during commissioning - does not work properly, the execution of the loaded application program can be halted by activating the safe-state mode. The safe-state mode does not permit control of the outputs via the bus or evaluation of the inputs. The device remains passive since the application program is not being executed (state-of-execution: terminated). Only the system software is still functional so that the ETS diagnosis functions and also programming of the device continue to be possible. Activating the safe-state mode o Switch off the bus voltage (e.g. by disconnecting the device from the bus line). o Press and hold down the programming button. o Switch on the bus voltage (e.g. by connecting the device to the bus line). Release the programming button only after the programming LED starts flashing slowly. The safe-state mode is activated. With a new brief press of the programming button, the programming mode can be switched on and off as usual also in the safe-state mode. The programming LED will nevertheless continue to flash independently of the programming mode as long as the safe-state mode is active. i The safe-state mode can be terminated by switching off the bus voltage or by programming with the ETS. Unloading the application program The application program can be unloaded with the ETS. In this case, the internal effect of the extension inputs on the Venetian blind output as part of the application program is not available either. The device does not then function. Order-No. 2165 00 Page 17 of 149
Page 1 and 2: KNX/EIB Product documentation Issue
Page 3 and 4: Product definition 1 Product defini
Page 5 and 6: Installation, electrical connection
Page 13 and 14: Technical data 3 Technical data Gen
Page 15: 4.2 Software "Venetian blind, input
Page 19 and 20: Software "Venetian blind, input 20B
Page 29 and 30: 4.2.4.3 Channel-orientated function
Page 37 and 38: 4.2.4.4 Channel-oriented functions
Page 67 and 68:
Software "Venetian blind, input 20B
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
- II. Sun protection with shading c
Page 81 and 82:
Page 83 and 84:
4.2.4.4.6 Settings for automatic he
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
4.2.4.5 Priorities for the output S
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Priority of sun protection with res
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Delay scene recall ? Yes No Softwar
Page 147 and 148:
Forced position on, lowering / clos
Page 149:
Appendix Gira Giersiepen GmbH & Co.
show all

Blind actuator 1-gang flush-mounted Order-No. 2165 00 - Gira

Create successful ePaper yourself

Delete template?

Save as template?