SL-24533.book(SL-24533 FC.fm) - Emerson Network Power

More documents

Recommendations

Info

Figure 8 Diagram of Npower with One or More Options Installed, and an OPS is not Installed UPSC MM PS Option 1 Option 2 TR TR TR TR TR Conn Conn Figure 5 Figure 9 Jumper Removal Jumper In PCB Jumper Out PCB Figure 5 Figure 9 shows an example of jumper removal. Please consult the documentation with each option to determine the location of the termination resistor jumper. 12 General information concerning 4 x 7 Option Cards
4.0 GENERAL OPTION INSTALLATION INSTRUCTIONS Using the Npower front control panel, put the Npower UPS to bypass and open the battery circuit breaker in accordance with instructions in the Operations and Maintenance Manual. With the Npower on bypass, unlock and open the front door of the Npower. See Figure 1. Use the rotary switch (at knee level) to mechanically set the Npower to Bypass. The rotary switch is located in the lower right front of the unit (Figure 1). Open the fuses for control power and fans, in accordance with the Operations and Maintenance Manual. With the switch in the Bypass position and the control power fuse open, the load will be supported by the utility but power will not be supplied to the option installation area in the Npower. With the front door open locate the option door on the right hand side of the cabinet. Loosen the two screws located on the left hand side of the option door. The option door will open to the right. See Figure 1. At the back of the option area are red composite shield panels, to prevent accidental contact with the input and output power terminals. Leave these shields in position. ! CAUTION Do not remove the red I/O Protective Shields. Behind the shields are input and output power terminals that will remain energized. As a minimum there will be an communications interface module (IFM board) mounted on the side of the compartment near the mid-point on the door. Other options may also have been previously installed. The Option boards mount on the inside of the option door (See Figure 1). Options should be located in accordance with Table 1 in Section 3.1. If other options have been previously installed, install the new option in the next higher adjacent available position. When the installer has selected the proper mounting position, he should use the KEPNUTS supplied with the Kit to attach the Option to the inside of the Option Door (See Figure 3) mounted on the studs as indicated. If this is the first option, and is not the option power supply or the NIC, install in Location 4. The UPS will have an already installed (CANbus) interface harness that is coiled up and located in the center of the option door. Attach this harness to the connector marked P999 on the left hand side of the option board. (See Figure 3 and Figure 10.) If this option is being installed in a UPS system that has previously installed option boards, the UPS CANbus harness will already be routed to the existing Option board(s). Two jumper cables will be supplied with the installation kit. A long jumper, to be used if the new board to be installed is distant from the existing connected board, and a short jumper if the new board and existing board are to be installed adjacent to each other. The jumper cables are numbered 77-814000-03 (short) and 77-814000-04 (long). The short cable is 14 inches and the long cable is 27 inches. Attach the correct jumper cable to the previously installed option, using the connector labeled P966 on the lower left section of the previously installed option. Run the jumper to the connector labeled P999 on the left of the New Option. (See Figure 3 and Figure 10). Subsequent new options will be installed in a similar fashion. The option located in position 4 (bottommost) should receive the UPS CANbus harness. Subsequent options will be connected in a daisy chain fashion via the jumper cable 77-814000-03 or 04 depending upon required length. See Section 8 for the installation of the OPS and Section 15 for the installation of the NIC. General Option Installation Instructions 13
Page 1: POWER PROTECTION Npower UPS OPTIONS
Page 4 and 5: 7.2 Installation . . . . . . . . .
Page 6 and 7: 18.2 General Description . . . . .
Page 8 and 9: Figure 50 Dial Out Phone Number Scr
Page 11 and 12: IMPORTANT SAFETY INSTRUCTIONS Save
Page 13 and 14: 2.0 OPTION DESCRIPTIONS The NpowerU
Page 15 and 16: 3.0 GENERAL INFORMATION CONCERNING
Page 17 and 18: Figure 2 Detail F and View B-B IFM
Page 19 and 20: Figure 5 Diagram of Npower with OPS
Page 21: Figure 6 Diagram of Npower with Add
Page 25 and 26: 5.0 ENABLING COMMUNICATION OPTIONS
Page 27 and 28: Figure 15 System Settings Screen wi
Page 29 and 30: 6.0 OPEN COMMS - DISCRETE OUTPUT OP
Page 31 and 32: Figure 20 Installing OC-DO with a P
Page 33 and 34: Figure 21 Customer Connections See
Page 35 and 36: 6.3 Programming the Open Comms - Di
Page 37 and 38: Figure 26 Programmable Output Relay
Page 39 and 40: You may attach up to four alarms to
Page 41 and 42: 6.5 Configuring the Programmable Re
Page 43 and 44: Figure 31 Wire Routing for OC-DI CA
Page 45 and 46: All harnesses and cables should be
Page 47 and 48: Figure 36 Contact Signal Assignment
Page 49 and 50: Figure 37 OPS Installation Detail D
Page 51 and 52: Figure 39 OPS Customer Connections
Page 53 and 54: 9.0 REMOTE ALARM STATUS PANEL (RAS)
Page 55 and 56: Figure 41 RAS Details B and C RED 1
Page 57 and 58: Table 6 Remote Alarm Status DIP Swi
Page 59 and 60: 9.3 Interpreting the LED indicators
Page 61 and 62: Figure 44 Installation of the Inter
Page 63 and 64: 10.3 Installation Instructions for
Page 65 and 66: The default status of the Modem sho
Page 67 and 68: Stop Bits 1 Terminal Emulation ANSI
Page 69 and 70: HLn? History Log 1, History Log 2,
Page 71 and 72: 11.0 SITESCAN INTERFACE SiteScan ca
Page 73 and 74:
Figure 52 Pager Support Screen PAGE
Page 75 and 76:
13.0 RS 232 PORT As a standard feat
Page 77 and 78:
14.1 MBB Board 14.1.1 Kit Contents
Page 79 and 80:
Figure 53 Multiple Battery Breaker
Page 81 and 82:
14.2 Input Contact Isolator (ICI or
Page 83 and 84:
14.2.3 Testing of ICI Board 1. Perf
Page 85 and 86:
Dimensions: Net: 178mm x 102mm x 38
Page 87 and 88:
Figure 58 Installing the NIC Option
Page 89 and 90:
15.5.3 Configuring the NIC on a Ser
Page 91 and 92:
15.5.3.5 Factory Settings Menu The
Page 93:
15.6.3 HTTP Status and alarm inform
Page 96 and 97:
Figure 66 HTTP Battery Screen Figur
Page 98 and 99:
Figure 69 HTTP Load Screen 88 Open
Page 100 and 101:
Table 10 LED Identifiers LED Identi
Page 102 and 103:
tainty of responding time of the Op
Page 104 and 105:
Function Code Support The OpenComms
Page 106 and 107:
RTU Framing Examples READ REGISTERS
Page 108 and 109:
15.8.6 Modbus Troubleshooting If th
Page 110 and 111:
! WARNING ENSURE THAT ALL CUSTOMER
Page 112 and 113:
Figure 75 Npower UPS 80 - 130 KVA 1
Page 114 and 115:
Figure 77 DC Ground Fault Wiring Co
Page 116 and 117:
17.0 AUTO RESTART The Auto Restart
Page 118 and 119:
The LBS Control Panel contains circ
Page 120 and 121:
To install the LBS Transformer Cabi
Page 122 and 123:
Figure 83 Details of Connection to
Page 124 and 125:
Control Fuse Assembly LBS Interface
Page 126 and 127:
Close and re-latch the control door
Page 128 and 129:
Figure 85 LBS Npower to Npower Wiri
Page 130 and 131:
Sync indicators will be lighted. Th
Page 132 and 133:
20.0 APPENDIX Table 14 Alarms, Func
Page 134 and 135:
Actual Alarm/fault Name Displayed O
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146:
show all

SL-24533.book(SL-24533 FC.fm) - Emerson Network Power

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?