SL-24533.book(SL-24533 FC.fm) - Emerson Network Power

More documents

Recommendations

Info

Figure 32 Customer Hookups for ICI To next option if installed To previously installed option or CANbus if first option OC-DI RELAY BOARD 8 Channels Each channel requires a user contact to activate 34 Open COMMS – Discrete Input Option (OC-DI) (Input Contact Isolator)
All harnesses and cables should be dressed and secured via tie wraps to make sure they do not move when the option door is closed. Excess cabling should be neatly coiled and tie wrapped NOTE Installation instructions are the same as for the OC-DO (Programmable Relay Board). See Section 6. 7.3 Programming the OC-DI (Input Contact Isolator Option) Enable the OC-DI option by following the instructions in Section 5 and selecting INPUT CONTACT ISOLA- TOR from the options list in the COMMUNICATIONS OPTIONS screen and follow the instructions for enabling an option. When the OC-DI Option has been enabled go to the CUSTOMER ALARM INTERFACE screen from the CON- FIGRUATION menu. Use the arrow keys to move to CONTACT BOARD, press SELECT. The following screen will appear: Figure 33 Alarm / Fault Name Screen ALARM / FAULT NAME ALARM / FAULT NAME L D F E DELAY INPUT CONTACT # 1 Y Y N Y 0.0 INPUT CONTACT # 2 Y Y N Y 0.0 INPUT CONTACT # 3 Y Y N Y 0.0 INPUT CONTACT # 4 Y Y N Y 0.0 INPUT CONTACT # 5 Y Y N Y 0.0 INPUT CONTACT # 6 Y Y N Y 0.0 UP DOWN SELECT EXIT DESCRIPTION: L - Latching...D - Dial... The top line will be blinking, indicating it is the selected contact. To scroll through the contacts use the indicators at the bottom of the screen. To move down through the list use the arrow keys to move the reverse video cursor to DOWN and Press SELECT. This will move INPUT CONTACT #2 to the top position of the list and it will be blinking, indicating it is the active contact ready to be configured. To return to INPUT CONTACT # 1, use the arrow keys to move to the UP indicator and Press SELECT. #1 will now be active. Along the bottom right of the display will be scrolling text to the right and including the word DESCRIPTION: This is defining the letters L,D,F,E, and DELAY for times when these instructions are not at hand. The letters stand for: L= Latching When set to Y and an alarm occurs, that alarm will stay active in the UPS system until the alarm condition is no longer true and the ALARM RESET button on the front panel of the UPS has been pushed. When set to N, the alarm will disappear from the UPS when the alarm conditions are no longer true. D= Dial Out – When an alarm condition occurs, a modem-equipped system can dial out to a number in accordance with the Dial Out instructions set in the UPS. F=Freeze - This function is factory set up as N and does not affect the operation of this option. E= Event – If Y is selected for this contact, and an alarm occurs, that alarm will be entered into the UPS’s Event Log. If N is selected and this alarm occurs, the event will not be posted in the event log and there will be no history of the event once the alarm is reset or the alarm condition disappears. DELAY= a delay in seconds that must occur before the UPS recognizes this alarm function. The delay can be anywhere from 0 to 99.9 seconds in 0.1 second intervals. Some customer-created alarms may be transitory and Operator may not want to alarm immediately unless the alarm condition persists. Use this function to set the Open COMMS – Discrete Input Option (OC-DI) (Input Contact Isolator) 35
Page 1: POWER PROTECTION Npower UPS OPTIONS
Page 4 and 5: 7.2 Installation . . . . . . . . .
Page 6 and 7: 18.2 General Description . . . . .
Page 8 and 9: Figure 50 Dial Out Phone Number Scr
Page 11 and 12: IMPORTANT SAFETY INSTRUCTIONS Save
Page 13 and 14: 2.0 OPTION DESCRIPTIONS The NpowerU
Page 15 and 16: 3.0 GENERAL INFORMATION CONCERNING
Page 17 and 18: Figure 2 Detail F and View B-B IFM
Page 19 and 20: Figure 5 Diagram of Npower with OPS
Page 21 and 22: Figure 6 Diagram of Npower with Add
Page 23 and 24: 4.0 GENERAL OPTION INSTALLATION INS
Page 25 and 26: 5.0 ENABLING COMMUNICATION OPTIONS
Page 27 and 28: Figure 15 System Settings Screen wi
Page 29 and 30: 6.0 OPEN COMMS - DISCRETE OUTPUT OP
Page 31 and 32: Figure 20 Installing OC-DO with a P
Page 33 and 34: Figure 21 Customer Connections See
Page 35 and 36: 6.3 Programming the Open Comms - Di
Page 37 and 38: Figure 26 Programmable Output Relay
Page 39 and 40: You may attach up to four alarms to
Page 41 and 42: 6.5 Configuring the Programmable Re
Page 43: Figure 31 Wire Routing for OC-DI CA
Page 47 and 48: Figure 36 Contact Signal Assignment
Page 49 and 50: Figure 37 OPS Installation Detail D
Page 51 and 52: Figure 39 OPS Customer Connections
Page 53 and 54: 9.0 REMOTE ALARM STATUS PANEL (RAS)
Page 55 and 56: Figure 41 RAS Details B and C RED 1
Page 57 and 58: Table 6 Remote Alarm Status DIP Swi
Page 59 and 60: 9.3 Interpreting the LED indicators
Page 61 and 62: Figure 44 Installation of the Inter
Page 63 and 64: 10.3 Installation Instructions for
Page 65 and 66: The default status of the Modem sho
Page 67 and 68: Stop Bits 1 Terminal Emulation ANSI
Page 69 and 70: HLn? History Log 1, History Log 2,
Page 71 and 72: 11.0 SITESCAN INTERFACE SiteScan ca
Page 73 and 74: Figure 52 Pager Support Screen PAGE
Page 75 and 76: 13.0 RS 232 PORT As a standard feat
Page 77 and 78: 14.1 MBB Board 14.1.1 Kit Contents
Page 79 and 80: Figure 53 Multiple Battery Breaker
Page 81 and 82: 14.2 Input Contact Isolator (ICI or
Page 83 and 84: 14.2.3 Testing of ICI Board 1. Perf
Page 85 and 86: Dimensions: Net: 178mm x 102mm x 38
Page 87 and 88: Figure 58 Installing the NIC Option
Page 89 and 90: 15.5.3 Configuring the NIC on a Ser
Page 91 and 92: 15.5.3.5 Factory Settings Menu The
Page 93: 15.6.3 HTTP Status and alarm inform
Page 96 and 97:
Figure 66 HTTP Battery Screen Figur
Page 98 and 99:
Figure 69 HTTP Load Screen 88 Open
Page 100 and 101:
Table 10 LED Identifiers LED Identi
Page 102 and 103:
tainty of responding time of the Op
Page 104 and 105:
Function Code Support The OpenComms
Page 106 and 107:
RTU Framing Examples READ REGISTERS
Page 108 and 109:
15.8.6 Modbus Troubleshooting If th
Page 110 and 111:
! WARNING ENSURE THAT ALL CUSTOMER
Page 112 and 113:
Figure 75 Npower UPS 80 - 130 KVA 1
Page 114 and 115:
Figure 77 DC Ground Fault Wiring Co
Page 116 and 117:
17.0 AUTO RESTART The Auto Restart
Page 118 and 119:
The LBS Control Panel contains circ
Page 120 and 121:
To install the LBS Transformer Cabi
Page 122 and 123:
Figure 83 Details of Connection to
Page 124 and 125:
Control Fuse Assembly LBS Interface
Page 126 and 127:
Close and re-latch the control door
Page 128 and 129:
Figure 85 LBS Npower to Npower Wiri
Page 130 and 131:
Sync indicators will be lighted. Th
Page 132 and 133:
20.0 APPENDIX Table 14 Alarms, Func
Page 134 and 135:
Actual Alarm/fault Name Displayed O
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146:
show all

SL-24533.book(SL-24533 FC.fm) - Emerson Network Power

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?