isel-CNC Machine - Bedienungsanleitungen / Manuals isel

More documents

Recommendations

Info

isel-CNC Machine CPV Multi I/O Card (2x) • PC plug-in card (l = 250 mm) for ISA slot • 16 opto-isolated signal inputs (+ 24 V, industry standard) • 8 relay outputs (+ 24 V switching, 300 mA) • Opto-isolated analog output (± 10 V) • Card output via 37-pin Sub D connector The multi I/O card with 16 inputs and 8 outputs (as a PC plug-in card) is tailored to the needs of binary-data acquisition and exchange. The PC card is 250 mm long and can be inserted into any PC or industrial computer using a 16-bit ISA bus connector. The settable basic address provides both a combination with other PC plug-in cards and a cascading of several multi I/O cards. Multi I/O card For more information, refer to the Readme file contained in the provided software. 26
isel-CNC Machine CPV UPMV 4/12 Servomotor Control Card • 4 independent axis processors • 32-bit set-value registers, acceleration registers • 32-bit position measurement • Programmable 16-Bit PID controller, sampling interval 0.35 ms • 12-bit D/A output (± 10 V speed set value) • 8 signal inputs for limit switches (opto-isolated) • 4 signal inputs for reference/zero-point switches (opto-isolated) • Signal input Output Stage Fault (opto-isolated) • Signal input Enable Limit Switch (opto-isolated) • Signal output Output Stage Shutdown (opto-isolated) • Signal output Enable Limit Switch (opto-isolated) • Connection via 50-pin ribbon connector The UPMV 4/12 servomotor control card is a PC plug-in card (approx. 380 mm long) for the selection of up to four d.c. servomotors. - It integrates four independent, digital axis processors, type National LM628. - Apart from the function blocks of the PID position control of the d.c. servomotors and setvalue generation, the processors also include the position measurement of the numerical axes by evaluating the pulse sequences using the incremental rotary encoder flanged on the motor. To suppress any line-borne interference, the signals on the rotary encoder side are converted to RS422 using symmetric signal drivers. The control card as an output to the external power output stage provides a speed set value of ± 10 V. A monitoring of the limit and reference switches in the servosystem is by evaluating opto-isolated + 24 V signal outputs. - In addition, the card has an input for fault messages of the output stage and outputs to short-circuit the limit switches, to switch off the power output stages and for safety shutdown of the PC card. - To install the card, a 16-bit ISA slot is required in the control computer. UPMV 4/12 servomotor control card 27
Page 1 and 2: isel-CNC Machine Operating and Main
Page 3 and 4: isel-CNC Machine CPV The CPV is a c
Page 5 and 6: isel-CNC Machine CPV 1 Intended Pur
Page 7 and 8: isel-CNC Machine CPV Aging of Safet
Page 9 and 10: isel-CNC Machine CPV During transpo
Page 11 and 12: isel-CNC Machine CPV 4 Start-Up 4.1
Page 13 and 14: isel-CNC Machine CPV 4.2 Installing
Page 15 and 16: isel-CNC Machine CPV 5 Cleaning / M
Page 17 and 18: isel-CNC Machine CPV 6 Troubleshoot
Page 19 and 20: isel-CNC Machine CPV 7 Technical Sp
Page 21 and 22: isel-CNC Machine CPV PVM 0810 Power
Page 23 and 24: isel-CNC Machine CPV BIG 1608 Termi
Page 25: isel-CNC Machine CPV Control Comput
Page 29 and 30: isel-CNC Machine CPV Software Inter
Page 31 and 32: isel-CNC Machine CPV - Fault at out
Page 33 and 34: isel-CNC Machine CPV 7.4 Evaluation
Page 35 and 36: isel-CNC Machine CPV 7.5 Connectors
Page 37 and 38: isel-CNC Machine CPV 7.6 Charts and
Page 39 and 40: isel-CNC Machine CPV 9 Appendix 39
Page 41 and 42: isel-CNC Machine CPV Please observe

isel-CNC Machine - Bedienungsanleitungen / Manuals isel

Create successful ePaper yourself

Delete template?

Save as template?