Service Manual PLATINUM ENG.pdf

More documents

Recommendations

Info

Ideas with Passion SECTION 3 BRIEF INSTRUCTIONS TALEA Section 03 REV.00 REV00 - August 06
Ideas with Passion 3.1 Client and programming menu Platinum Vision Press “go to menu” The programming menu will open. Detailed beverage programming To set current time Beverage settings Clock Main menu Machine settings Maintenance settings Machine function programming Show text 8:30 a Go to diagnostics Next page Next Go back Exit After setting each of the following menus, press: - “Go back” to be returned to the previous screen and save any new settings. - “Previous settings” to reset previous values. - “Go back to menu” to be returned to the main menu and save new settings. Machine settings Language & display Water settings Cup warmer Machine settings menu. - Language & display = to set menu language and display contrast. - Water settings = to set some water functions. - Cup warmer = to set cut warmer functions. Go back to menu Go back Beverage settings menu To set general parameters for the dispense of beverages containing coffee, press the “beverage settings” key in the main menu. Beverage settings Espresso Coffee Long coffee The following can be set for each beverage selected: Go back to menu Go back Coffee settings Pre-brewing of coffee Pre-brewing normal Temperature medium The temperature of the dispensed coffee. The amount of coffee to be ground and use of pre-ground coffee. Aroma normal Go back to menu Water quantity 240 / 500 Go back The amount of water to be used in dispensed coffee. Clock menu To set the current time and timer (for standby), press the “clock settings” key on the main menu. To set current time. Time Clock settings Stand-by To set stand-by parameters after coffee is dispensed. Go back to menu Go back TALEA Section 03 REV00 - August 06 1/3
Page 1 and 2: TECHNICAL SERVICE MANUAL Emissione
Page 3 and 4: SECTION 1 INTRODUCTION TALEA Sectio
Page 5 and 6: Ideas with Passion 1.4 Platinum ran
Page 7 and 8: SECTION 2 TECHNICAL DATA TALEA Sect
Page 9: Internal components Heater Pump Sta
Page 13 and 14: Ideas with Passion 3.2 Maintenance
Page 15 and 16: Ideas with Passion 4.1 Wiring diagr
Page 17 and 18: Ideas with Passion Platinum Swing 3
Page 19 and 20: Ideas with Passion 4.2 Platinum wat
Page 21 and 22: Ideas with Passion - Milk island pr
Page 23 and 24: Ideas with Passion Platinum Swing e
Page 25 and 26: Ideas with Passion Level M4 At this
Page 27 and 28: Ideas with Passion Messages/Alarms
Page 29 and 30: Ideas with Passion POSITION POTENTI
Page 31 and 32: Ideas with Passion DIP SWITCH ON ON
Page 33 and 34: Ideas with Passion Level M3 : Error
Page 35 and 36: Ideas with Passion 5.3 Error messag
Page 37 and 38: SECTION 6 OPERATING LOGIC TALEA Sec
Page 39 and 40: Ideas with Passion 6.3 Motorized tr
Page 41 and 42: Ideas with Passion 6.5 SBS Valve Be
Page 43 and 44: Ideas with Passion 6.6 Solenoid pil
Page 45 and 46: Ideas with Passion SECTION 7 COMPON
Page 47 and 48: Unscrew the four screws which block
Page 49 and 50: Ideas with Passion 7.3 Electronics
Page 51 and 52: Ideas with Passion 7.5 Pump 1 2 Tak
Page 53 and 54: Ideas with Passion 7. 7 OETIKER cla
Page 55 and 56: 7.9 Coffee grinder setting, assembl
Page 57 and 58: Ideas with Passion 7.11 Motorized d
Page 59: Ideas with Passion 8.1 Routine main

Service Manual PLATINUM ENG.pdf

Create successful ePaper yourself

Delete template?

Save as template?