BLADE BALANCER
BLADE BALANCER
BLADE BALANCER
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Bag L<br />
Tail Unit Assembly-4 / -4<br />
No.<br />
1<br />
2<br />
Material No.<br />
HME3-3B<br />
HNU2-9Z<br />
Description<br />
SET SCREW M3×3<br />
SHOULDERED SCREW M2×9<br />
名 稱<br />
無 頭 內 六 角 螺 絲 M3×3<br />
圓 頭 十 字 軸 套 螺 絲 M2×9<br />
Qty<br />
1<br />
2<br />
No.<br />
3<br />
4<br />
5<br />
Material No.<br />
BK1501<br />
HSA2-6<br />
HMM2Z<br />
Description<br />
名 稱<br />
3D CARBON TAIL FIN<br />
BUTTON HEAD SOCKET SCREW, M2X6<br />
LUCK NUT, M2<br />
3D 碳 纖 維 垂 直 安 定 面<br />
半 圓 頭 內 六 角 螺 絲<br />
止 鬆 螺 帽<br />
Qty<br />
1<br />
2<br />
2<br />
HME3-3B<br />
SET SCREW M3×3<br />
無 頭 內 六 角 螺 絲 M3×3<br />
HNU2-9Z<br />
SHOULDERED SCREW M2×9<br />
圓 頭 十 字 軸 套 螺 絲 M2×9<br />
Step 1 / 步 驟 一<br />
1. Slide the tail rotor set into the Tail Rotor Shaft.<br />
Line the hole up with the concave on the shaft.<br />
2. Secure the tail rotor set tightly by the Set<br />
Screw with a drop of threadlocking.<br />
1. 將 組 裝 完 成 的 尾 舵 控 制 臂 與 夾 片 組 安 裝 至 尾 橫 軸 。<br />
2. 無 頭 內 六 角 螺 絲 需 準 確 安 裝 於 尾 橫 軸 固 定 孔 位 , 並<br />
使 用 防 鬆 膠 。<br />
T22<br />
(1)<br />
(2)<br />
T22<br />
Note / 注 意<br />
Line up the concave of tail rotor<br />
shaft and the hole of hub.<br />
尾 橫 軸 上 凹 槽 對 正 轉 座 上 螺 絲 孔 。<br />
T22<br />
Step 2 / 步 驟 二<br />
Fit the Tail Pitch Control Links to the Tail Pitch Control<br />
Set. Do not over tighten the Socket Screw and ensure<br />
the tail linkages run effortlessly.<br />
將 控 制 連 桿 與 控 制 臂 連 接 , 請 使 用 適 量 螺 絲 防 鬆 劑 , 勿 過 度 鎖<br />
緊 固 定 螺 絲 , 並 確 認 機 構 可 以 靈 活 作 動 。<br />
HSA2-6<br />
BUTTON HEAD SOCKET SCREW, M2X6<br />
半 圓 頭 內 六 角 螺 絲<br />
HMM2Z<br />
LUCK NUT, M2<br />
止 鬆 螺 帽<br />
(5)<br />
(2)<br />
Completed View<br />
組 裝 完 成<br />
Step 3 / 步 驟 三<br />
Attach the Carbon Tail Fin to the Tail Unit as shown.<br />
將 碳 纖 垂 直 安 定 翼 固 定 於 尾 管 座 。<br />
(4)<br />
(3)<br />
-20-