BLADE BALANCER
BLADE BALANCER
BLADE BALANCER
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Bag N<br />
Electric System-1 / -1<br />
No.<br />
1<br />
2<br />
3<br />
Material No.<br />
BK1890<br />
HSA3-5B<br />
HME3-3B<br />
Description<br />
MOTOR MOUNT<br />
SOCKET SCREW M3×5<br />
SET SCREW M3×3<br />
名 稱<br />
馬 達 座<br />
半 圓 頭 內 六 角 螺 絲 M3×5<br />
無 頭 內 六 角 螺 絲 M3×3<br />
Qty<br />
1<br />
2<br />
1<br />
No.<br />
4<br />
5<br />
Material No.<br />
BK1009<br />
HSA2-6<br />
Description<br />
DRIVE GEAR 13T<br />
BUTTON HEAD SOCKET SCREW M2X6<br />
名 稱<br />
驅 動 齒 輪 13T<br />
半 圓 頭 內 六 角 螺 絲 M2x6<br />
Qty<br />
1<br />
4<br />
HSA3-5B<br />
SOCKET SCREW M3×5<br />
半 圓 頭 內 六 角 螺 絲 M3×5<br />
HME3-3B<br />
SET SCREW M3×3<br />
無 頭 內 六 角 螺 絲 M3×3<br />
Note 1 / 注 意 1<br />
1. The length from the end of Drive Gear to Motor Mount is 16mm.<br />
2. Please select the Drive Gear based on your motor & battery.<br />
The OBL 29/37-10H (No. 2382) Brushless Motor and 13T<br />
pinion are recommended for mini Titan V2 with ACE<br />
Power 3S1P Li-Po battery.<br />
1. 驅 動 齒 輪 末 端 至 馬 達 座 距 離 為 16mm。<br />
2. 請 依 馬 達 及 電 池 種 類 搭 配 驅 動 齒 輪 。 使 用 ACE<br />
RC OBL 29/37-10H 無 刷 馬 達 , 建 議 搭 配<br />
13T 驅 動 齒 輪 及 3S1P 鋰 聚 電 池 組 。<br />
(1)<br />
HSA2-6<br />
BUTTON HEAD SOCKET SCREW M2X6<br />
半 圓 頭 內 六 角 螺 絲 M2x6<br />
T22<br />
(2)<br />
Step 1 / 步 驟 一<br />
1. Mount the motor to the Motor Mount.<br />
2. Secure the Drive Gear to the motor shaft tightly<br />
with a drop of threadlocking.<br />
1. 將 馬 達 固 定 於 馬 達 固 定 片 上 。<br />
2. 使 用 適 量 防 鬆 劑 將 驅 動 齒 論 固 定 於 馬 達 主 軸 上 。<br />
T22<br />
(2)<br />
(3)<br />
T22<br />
(4)<br />
16mm<br />
Note 2 / 注 意 2<br />
You can observe the gear mesh from the bottom<br />
of Bottom Bracket.<br />
您 可 從 機 體 底 部 檢 視 齒 輪 間 隙 。<br />
Step 2 / 步 驟 二<br />
1. Install the Motor Mount into the main frame.<br />
2. Adjust the mesh between the Main Gear and Drive Gear<br />
until there is a small amount of backlash all the way.<br />
1. 將 組 裝 好 的 馬 達 座 固 定 於 機 身 。<br />
2. 調 整 好 齒 輪 間 隙 之 後 , 確 實 固 定 馬 達 座 。<br />
T22<br />
(5)<br />
T22<br />
T22<br />
(5)<br />
-23-