Industrial shaft seals

gab.ru
Wear
Берг
sleeves
АБ bergab@ya.ru Тел. (495)-228-06-21, факс (495) 22
Speedi-Sleeves – Inch sizes
D
d
da
Ba
B 1
B 2
Shaft diameter Sleeve dimensions SKF Designation
d a d D B 1 B 2 B a
1)
min max ±0.063 ±0.031 ±0.031
in in –
0.469 0.475 0.472 0.610 0.236 0.331 1.875 CR 99049
0.498 0.502 0.500 0.610 0.250 0.344 2.000 CR 99050
0.547 0.551 0.551 0.752 0.251 0.389 1.831 CR 99055
0.560 0.566 0.563 0.750 0.250 0.391 1.831 CR 99056
0.589 0.593 0.591 0.750 0.197 0.354 1.862 CR 99059
0.623 0.627 0.625 0.750 0.313 0.406 2.000 CR 99810*
0.625 0.750 0.313 0.406 2.000 CR 99062
0.624 0.630 0.630 0.752 0.315 0.437 2.000 CR 99058
0.667 0.671 0.669 1.063 0.313 0.433 2.000 CR 99068
0.682 0.686 0.684 0.900 0.313 0.438 2.000 CR 99060
0.704 0.709 0.706 1.063 0.315 0.433 1.811 CR 99082
0.748 0.752 0.750 0.945 0.313 0.438 2.000 CR 99871*
0.750 0.945 0.313 0.438 2.000 CR 99076
0.759 0.761 0.760 0.938 0.313 0.438 2.000 CR 99081
0.780 0.784 0.781 0.935 0.313 0.438 2.000 CR 99080
0.785 0.789 0.787 0.930 0.313 0.133 2.000 CR 99078
0.857 0.861 0.859 1.155 0.250 0.375 2.000 CR 99086
0.861 0.866 0.866 1.189 0.260 0.358 1.854 CR 99084
0.866 1.188 0.315 0.472 1.813 CR 99085
0.873 0.877 0.875 1.094 0.313 0.438 2.000 CR 99812*
0.875 1.094 0.313 0.438 2.000 CR 99087
0.908 0.912 0.910 1.218 0.313 0.438 1.847 CR 99860*
0.910 1.218 0.313 0.438 1.847 CR 99091
0.940 0.945 0.945 1.130 0.315 0.437 2.000 CR 99092
0.966 0.970 0.969 1.130 0.313 0.438 2.000 CR 99094
0.969 1.130 0.625 0.719 2.000 CR 99096
* Indicates Speedi-Sleeve Gold
1) Possible max. distance of rear groove from shaft end when installation tool supplied with sleeve is used
gab.ru 298Берг АБ bergab@ya.ru Тел. (495)-228-06-21, факс (495) 22