TOPAX DE Operation & Maintenance Instructions

More documents

Recommendations

Info

10 | Operating Manual TOPAX DE | Overview of Device Operation Functions
2. Device Installation and Connection Installation Schematic diagrams and dimensions are provided over the next few pages herein. A 92x92mm cut-out is required for the device casing. The device must then be pushed in from the fore end and fixed in with the appropriate lock-on clips provided on issue. The wall-mount casing can either be hung up to or foisted into the assembly slot, according to preference. It must then be fixed on with two screws. CAUTION The device assembly site must be selected so that the device is not subject to any mechanical load or chemical exposure in any way! Please note that the relative protection classes are: built in casing: IP54 for the front end, with IP55 at the front end door wall-mounted casing: IP65 (with closed clamp covers) CAUTION! Connections: Connection diagrams are provided over the next few pages herein. Please beware of the supply voltage specified on the rating plate at all times. CAUTION Input, output and control lead wires and cables must always be kept unattached from one another. In particular, they must be totally detached from power lines! All input and output wires and cables need to be shielded. The shielding can bear on one end only. For safe measurement data protection from any external disrupting influences, exclusive use of the specially shielded cable provided on issue to ensure effective measurements, is required. For Pt100 temperature sensor connection, use of a low-ohm cable with a large section is required. Upon relay connection, please beware that inductive loads need to be interference-suppressed. If this is not possible, the device terminal strip relay contacts need to be provided with an RC-protective circuit. With direct-current voltage, the relays or contactor coil need to be interference-suppressed via a free wheeling diode. CAUTION! Power up to: Capacitor C Resistor R R C 60 mA 10 nF 260V 390 Ohm 2 Watt 70 mA 47 nF 260V 22 Ohm 2 Watt 150 mA 100 nF 260V 47 Ohm 2 Watt 1,0 mA 220 nF 260V 47 Ohm 2 Watt Device Installation and Connection | Operating Manual TOPAX DE | 11
Page 1 and 2: TOPAX DE For free chlorine, chlorin
Page 3 and 4: 6. Controller Unit Settings........
Page 5 and 6: 3.) WARNING! Risk of electric shock
Page 7 and 8: 1.13 Overview of Device Operation F
Page 9: 1.15 Technical Specifications Featu
Page 13 and 14: 2.2 Installation of built-in casing
Page 15 and 16: 2.4 Terminal connection diagram of
Page 17 and 18: 2.5 Terminal connection diagram of
Page 19 and 20: 3. Directions on Device Operations
Page 21 and 22: NOTE! If you do not wish to save th
Page 23 and 24: Contr. release Input active with lo
Page 25 and 26: 5. Metering Unit Settings Free chlo
Page 27 and 28: 0.44mg/l 7.24pH 736mV 27.2°C MAN >
Page 29 and 30: 6. Controller Unit Settings The con
Page 31 and 32: Meter test **TOPAX DE 2 P-min 0.5s
Page 33 and 34: NOTE! Measuring value trend display
Page 35 and 36: h —— —— —— —— 10s 0
Page 37 and 38: 7. Alarm Alongside the metering con
Page 39 and 40: 7.1 Alarm messages Error message Ev
Page 41 and 42: 8.3 Assembly of a Data Network (Top
Page 43 and 44: CAUTION! With a defect in the TOPAX
Page 45 and 46: mA A outputs3 3 3 english french sp
Page 47 and 48: H Hysterese........................
Page 49 and 50: 12. Declaration of conformity This
Page 51 and 52: 14. Warranty Please copy and send w

TOPAX DE Operation & Maintenance Instructions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?