DeNight Special 50 Manual - CMC Versand

More documents

Recommendations

Info

Step 5 Install the canopy and secure it with two 4-40 x 3/8- inch Allen head screws using a 3/32-inch hex wrench. Step 7 Slide the wings onto the tube and connect the aileron leads from the wing to the servo extension leads from the receiver. Step 9 Slide the wing panels all the way against the fuselage, engaging the anti-rotation pins in the wing with the holes in the wing root. Turn the model over and secure the wing panels to the fuselage by installing the 4-40 screws and washers with a 3/32-inch hex wrench. Step 6 Insert the wing tube into the fuselage. Step 8 Prepare the wing retaining screws by placing a #4 steel washer onto each of the 4-40 x 5/8-inch Allen head machine screws. 42 DeNight Special 50 ARF Assembly Manual
Center of Gravity An important part of preparing the aircraft for flight is properly balancing the model. Caution: Do not inadvertently skip this step! The recommended Center of Gravity (CG) location for your model is 2 5/8 (67mm) to 3 1/8 inches (79mm) behind the leading edge of the wing where it meets the fuselage. Mark the location for the Center of Gravity on a piece of low-tack tape on the top of the wing next to the fuselage as shown. When balancing your model, support the model inverted at the marks made on the top of the wing with your fingers or a commercially available balancing stand. This is the correct balance point for your model. You may find you need to add a small amount of weight to either the front or back of the fuselage to achieve the correct balance. Control Throws Step 1 Turn on the transmitter and receiver of your model. Check the movement of the rudder using the transmitter. When the stick is moved right, the rudder should also move right. Reverse the direction of the servo at the transmitter if necessary. Step 2 Check the movement of the elevator with the radio system. Moving the elevator stick toward the bottom of the transmitter will make the elevator move up. Step 3 Check the movement of the ailerons with the radio system. Moving the aileron stick right will make the right aileron move up and the left aileron move down. Step 4 Use a ruler to adjust the throw of the elevator, ailerons and rudder. Aileron High Rate Up 1 inch (25mm) Down 7/8 inch (22mm) Aileron Low Rate Up 3/4 inch (19mm) Down 5/8 inch (16mm) Elevator High Rate Up 13/16 inch (21mm) Down 13/16 inch (21mm) Elevator Low Rate Up 5/8 inch (16mm) Down 5/8 inch (16mm) Rudder High Rate Left 1 1/8 inch (29mm) Right 1 1/8 inch (29mm) Rudder Low Rate Left 3/4 inch (19mm) Right 3/4 inch (19mm) Note: Measurements are taken at the inner or widest point on the control surface. These are general guidelines measured from our own flight tests. You can experiment with higher rates to match your preferred style of flying. Note: Travel Adjust, Sub-Trim and Dual Rates are not listed and should be adjusted according to each individual model and preference. DeNight Special 50 ARF Assembly Manual 43
Page 1 and 2: DeNight Special 50 ARF Assembly Man
Page 3 and 4: Included Parts Listing Packaged in
Page 5 and 6: Using the Manual This manual is div
Page 7 and 8: Step 5 Slide a 2 3/4-inch wheel ont
Page 9 and 10: Step 4 Insert the stabilizer in the
Page 11 and 12: Step 16 Remove the T-pins and push
Page 13 and 14: Step 4 Remove the standard arm with
Page 15 and 16: Step 14 Repeat step 13 to connect t
Page 17 and 18: Step 10 Apply 2-3 drops of thin CA
Page 19 and 20: Step 2 Locate the countersunk machi
Page 21 and 22: Cowling and Spinner Installation -
Page 23 and 24: Step 2 Temporarily install the tray
Page 25 and 26: Step 6 Use a #1 Phillips screwdrive
Page 27 and 28: Step 8 Place the fuselage left-hand
Page 29 and 30: Step 2 Use a #1 Phillips screwdrive
Page 31 and 32: Step 14 Slide the plywood standoff
Page 33 and 34: Step 2 Identify the vent and feed l
Page 35 and 36: Step 14 Remove the template. Use a
Page 37 and 38: Step 23 Remove the template, hatch
Page 39 and 40: Receiver, Battery and Switch Instal
Page 41: Final Assembly Parts Required Fusel
Page 45 and 46: Safety Do’s and Don’ts for Pilo
Page 47 and 48: Non-Warranty Repairs Should your re
Page 49 and 50: Templates Align to rear edge of cow
Page 51 and 52: Building and Flying Notes DeNight S

DeNight Special 50 Manual - CMC Versand

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?