EQ Station Manual v. 2.01 sw. 220 English - TC Electronic

More documents

Recommendations

Info

EDIT CONTROL A yellow dot in the top of the display indicates when max. settings are reached. This typically occurs when a combination of adjustments on a specific band are made in both the Global window and on an individual channel. Copy Paste function Example: The 1kHz band is boosted 7dB via the All page but was previously boosted 6dB via the regular channel page. As the two boosts added gives a 13dB boost which is 1dB more than the possible 12dB, a yellow dot in the top of the band (see illustration) indicates this situation. Group Graphic EQ The Copy/Paste function is very useful for quickly moving channel settings from one channel to another. This is e.g. useful when one channel is adjusted in a monitor-mix setup, and these settings then should be used as starting point on other channels before further refinement of these. The Group functionality is similar to the Graphic EQ ALL channels adjust function, except that it is here possible to make a pre-defined group of channels instead of adjusting all channels. The Group is selected on available channels in the device. If in a network, a group can be made among all possible 64 channels. Flat All - Flat Group A flatten all function in both the All and Group functionality is available. • Press COPY + PASTE simultaneously • Press OK to confirm Basic Operation • Select channel and processing block and press the Copy button. • Select the channel you want to paste into, with the Channel wheel. • Press Paste and OK to confirm. The transfer of settings is now done. It is possible to copy/paste following: • Select Channel edit view to copy/paste the entire channel processing settings including. all EQ's, Limiter and Delay. • Select Parametric EQ edit view to copy/paste the parametric EQ block. • Select Graphic EQ edit view to copy/paste the graphic EQ block. • Select Dynamic EQ edit view to copy/paste the dynamic EQ block. What is copied it is always the current view that is copied. When in the “All” display, all settings for the entire channel is copied. not just the settings on the All page, but also settings for the Parametric, Graphic and Dynamic EQs. This also goes, no matter if the different EQ sections are active or not. 36
EQ STATION IN A LOCAL AREA NETWORK 37
Page 3 and 4: IMPORTANT SAFETY INSTRUCTIONS The l
Page 5 and 6: introduction TABLE OF CONTENTS Intr
Page 7 and 8: QUICK SETUP REFERENCE ... if you ju
Page 9 and 10: QUICK SETUP REFERENCE Cluster Auto
Page 11 and 12: FRONT PANEL CHANNEL SELECT wheel Us
Page 13 and 14: REAR PANEL Digital I/O With the opt
Page 15 and 16: GRAPHICAL EQ TYPES IN THE EQ STATIO
Page 17 and 18: GRAPHICAL EQ TYPES IN THE EQ STATIO
Page 19 and 20: GLOBAL VIEW Press..... ....and sele
Page 21 and 22: LOCAL VIEW Local page - Introductio
Page 23 and 24: EDITING Channel View Edit - Delay/L
Page 25 and 26: EDITING Graphic EQ Edit The Graphic
Page 27 and 28: EDITING CrossOver 2 Range: Off to 1
Page 29 and 30: Channel presets The Channel presets
Page 31 and 32: CONTROL SECTION Setup page The Setu
Page 33 and 34: SETUP PAGE Mute When a Clock Error
Page 35 and 36: UTILITY PAGE In - Channel select on
Page 37: EDIT CONTROL Show Preset Name On/ O
Page 41 and 42: EQ STATION IN A LOCAL AREA NETWORK
Page 43 and 44: VIRTUAL EQ STATION The drop down me
Page 45 and 46: MIDI IMPLEMENTATION EQ STATION - MI
Page 47 and 48: MOTOFADER 64 ALL, GROUP, COPY/PASTE
Page 49: MOTOFADER 64 Store/Recall via Motof

EQ Station Manual v. 2.01 sw. 220 English - TC Electronic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?