KalzipÂ® Systems

More documents

Recommendations

Info

Design specifications 6.6.3 The purlin roof: Kalzip parallel to inner skin The clips are fixed to the purlins or the inner skin spans parallel to the Kalzip sheet. Depending on the design of the bottom skin, an inter mediate section may be necessary with double skin roofs. The clips are normally positioned on top of each purlin. In re-roofing projects with narrow spaced purlins it may be sufficient to position the clips on every second purlin only. With regard to an even load distribution the clips are alternately arranged on the purlins. A design calculation is required. Please consult our local representative for design calculations. Non-ventilated Kalzip roof on purlins with trapezoidal inner sheet Positioning scheme 3 Clips Positioning scheme 4 Clips Clip positions with closer spaced purlins (Refurbishment) Ridge Ridge Clip Gable end Purlin Kalzip Purlin Clip Kalzip Eaves Eaves Cover width Kalzip Rafter spacing Rafter spacing Cover width Kalzip Rafter spacing Rafter spacing d = clip distance = purlin spacing c = purlin spacing d = clip distance Distances not to scale 38 Kalzip
Design specifications 6.6.4 Kalzip DuoPlus 100 and Kalzip Duo 100 The Kalzip DuoPlus 100 system always consists of a full layer of 10 cm thick, rigid thermal insulation, the DuoPlus rail, the DuoPlus clip and the special screws for fixing the rail onto the substructure. In contrast to this, the Kalzip Duo 100 system does not contain a full layer of rigid thermal insulation. Strips of rigid insulation with a width of 24 cm and a thickness of 10 cm are simply inserted under the Kalzip DuoPlus 100 rails. In the case of both systems, only the named components will be permitted. The arrangement of the rails and the number of connecting elements are outlined in the installation plan. The DuoPlus clips are secured against shifting by means of a plastic strip that is attached in the factory. First of all the rigid thermal insulation is placed on the substructure. A full layer of rigid insulation is used in the case of Kalzip DuoPlus 100. Strips of rigid insulation are used in the Kalzip Duo 100 system and any spaces between these strips are filled with soft thermal insulation or rigid insulation. The DuoPlus rails are then arranged on the thermal insulation in accordance with the installation plan and are connec ted to the substructure through the thermal insulation. The special DuoPlus clips are inserted into the rail and rotated so that they are positioned parallel to the seam direction (minimum rotation angle = 45°). The first row of clips, at the start of the installation surface (gable end), is aligned precisely and fixed into the rail by means of a screw through the base of the clip. The remaining clips are inserted into the rail and positioned parallel to the Kalzip seam direction. Every tenth row of clips is fixed with a screw to prevent shifting. The final row of clips, at the end of the installation surface (gable end), is also secured into the rail by means of a screw through the clip base. The compressible thermal insulation is then placed on top and pressed over the clips. The Kalzip roof structure can then be installed as normal. The DuoPlus rail must be long enough to cover at least two ribs of the trape zoidal deck and can be secured in it. If this is not possible, then a section of adequate length can be installed next to the first row (see positioning diagram for rafter roof and purlin roof). Positioning scheme Kalzip rafter roof The system requires that the DuoPlus rails are positioned at an angle of 45°. Clip spacing Gable end 45° Rafter spacing Rafter spacing Ridge DuoPlus clips Eaves Rail spacing DuoPlus rail Positioning scheme Kalzip purlin roof The system requires that the DuoPlus rails are positioned parallel to the purlins. Gable end Rafter spacing Rafter spacing Ridge Eaves DuoPlus rail DuoPlus clips Panel spacing = Clip spacing Distances not to scale Kalzip 39
Page 1 and 2: Kalzip ® Systems Product informati
Page 3 and 4: Page 6. Design specifications 6.1 M
Page 5 and 6: Innovations 2. Kalzip innovations T
Page 7 and 8: The system and its components Furth
Page 9 and 10: The system and its components Use o
Page 11 and 12: The system and its components Kalzi
Page 13 and 14: The system and its components Drip
Page 15 and 16: The system and its components left
Page 17 and 18: Kalzip range of applications Non-ve
Page 19 and 20: Kalzip range of applications Kalzip
Page 25 and 26: General data and characteristics 5.
Page 33 and 34: Design specifications 6. Design spe
Page 35 and 36: Design specifications 6.5 Lightning
Page 37: Design specifications • A contino
Page 41 and 42: Design specifications The Kalzip pr
Page 43 and 44: Design specifications 6.8 Thermal e
Page 45 and 46: Design specifications Sealed joints
Page 47 and 48: Dimensioning tables 7. Kalzip dimen
Page 49 and 50: Dimensioning tables 7.3.2 Purlin ro
Page 51 and 52: Index A accessibility 26, 29 access

KalzipÂ® Systems

Create successful ePaper yourself

Delete template?

Save as template?