Compatible Control - HUBER

More documents

Recommendations

Info

Preparing the thermostat for use Thermal Fluid Prepara- tory measures for thermal fluid circulation 3. Commissioning 3.2 Connecting Mains Power and Media Applies to bath thermostats with external pump connection For internal thermoregulation, please proceed as follows: close the pump connections with plugs and sleeve nuts (M16x1 / 19 spanner/wrench), at the same time hold against it at the pump connection with 17 spanner/wrench. For external thermoregulation, please proceed as follows: remove the plugs and sleeve nuts on the pump connections. Replace them with appropriate hose connection to your external application. For more information please see chapter 4 „thermoregulation via controller“. Applies to chillers (thermostats with closed external circulation) R2 R2 Make sure that the draining valve is closed. (Upright position or „right stop“). Connect hoses at connecting pieces 10 and 11 for circulating thermal fluid to and from the external device (if fitted). Note: Recommended tightening torques for hose couplings when using silicone oil as thermal fluid: M16x1 30 Nm M30x1.5 85 Nm Alternative: Hoses can be connected via shut-off valves. (Please refer to your Huber catalogue under „accessories“). If fitted, close valves only when performing work on the reactor. Remember that thermal fluid expands and contracts with changes in temperature. Sealing the external application will expose the application to these forces! 20 12 12 open close 10 11 Verify the following: Make sure that all connections are correct and that there are no leaks. For water-cooled thermostats: Unobstructed inflow and outflow of the cooling-water exists Pressure difference between the cooling-water inflow and outflow is 3 to 5 bar. Cooling-water supply temperature is 15°C to 25°C.
MEDIA Prepara- tory measures for water cooling Prepara- tory measures for cooling baths CCx-K12 to CCx-K25 3. Commissioning 3.2 Connecting Mains Power and Media Applies to water-cooled thermostats only 4.1 4.2 1 2 3 4 Using suitable hosing, connect the Huber watercooled unit to the cooling water supply via connections 26 and 27. Open all the water supply valve slowly and check for leaks. 26 27 Mains supply* (from Compatible Control CC-E to cooling bath) Control connection* (from Compatible Control CC-E to cooling bath) Main switch I = On (continuous duty of the cooling machine) 0= Off II= „Auto.“ the compressor is automatically controlled Mains supply 2 3 (fuse protected) 1 Rear side of CC-K12 * These connectors have to be plugged in even if the cooling bath is not being automatically controlled, otherwise the error message „SENSOR COND.!!“ will be displayed (refer to error code -11, 6.3 Device Messages - Soft Alarms). 21 �� Rear side of Compatible Control CC-E (Immersion Thermostat) 4
Page 1: Version 2.0 /08 Compatible Control
Page 4 and 5: Preface Dear Customer, Congratulati
Page 6 and 7: Unichiller with Compatible Control
Page 9: Contents Preface 1. Safety 1.1 Inte
Page 12 and 13: 1. Safety 1.1 Intended Use General
Page 15 and 16: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Page 17 and 18: 1 2 3 4 5 6 7 8 Removable, exchange
Page 19 and 20: 1 2 3 4 5 6 7 8 9 Removable, exchan
Page 21: 3. Commissioning
Page 24 and 25: DIN 12876 3. Commissioning 3.1 Safe
Page 26 and 27: Hazards through emission of fluids
Page 30 and 31: Overtemperature protection Requirem
Page 32 and 33: Fill the bath 3. Commissioning 3.4
Page 34 and 35: Fill the thermostat 3. Commissionin
Page 36 and 37: Language Deutsch Setpoint Minimum S
Page 39 and 40: Checks to be performed: Test Arrang
Page 41 and 42: Selection 4. Thermoregulation via C
Page 43 and 44: Display Time Scale Mains Failure Au
Page 45 and 46: Compressor Auto Heating Capacity So
Page 47 and 48: Analog Interface Caution! Electroni
Page 49 and 50: Digital Interface 4. Thermoregulati
Page 51 and 52: Acoustic Alarm Select Usermenu Conf
Page 53 and 54: Calibra- tion Prog. 4. Thermoregula
Page 55 and 56: Circulation Venting 2. Setpoint 4.
Page 57 and 58: Start Ramp 4. Thermoregulation via
Page 59 and 60: Edit Program 4. Thermoregulation vi
Page 61 and 62: Edit Program 4. Thermoregulation vi
Page 63: Abort Schematic diagram See 2.3. 4.
Page 67 and 68: Draining Thermofluid Draining cooli
Page 69 and 70: Requirements Replacing fuses Cleani
Page 71: 6. Appendix
Page 74 and 75: Interface Specification Float Switc
Page 76 and 77: Hardware error ALARM !!! HARDWARE E
Page 78 and 79:
6. Appendix 6.3. Device Messages 2.
Page 80 and 81:
Bath Volume (also referred to as fi
Page 82 and 83:
Flow Temperature Denotes the temper
Page 84 and 85:
Process Temperature (core temperatu
Page 86:
Viscosity Also referred to as „in
show all

Compatible Control - HUBER

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?