Compatible Control - HUBER

More documents

Recommendations

Info

Language Deutsch Setpoint Minimum Setpoint Maximum Setpoint 3. Commissioning 3.5 Major Pre-settings When delivered the controller displays will be in German. Other options can be selected in the „Language“ menu (refer to 4.3.2): English, Francais The thermostat controls the temperature to the predefined setpoint. Use the SET key and the encoder to select other options. The permissible setpoints are limited to the range of the minimum and maximum setpoints. The option „setpoint limit“ allows this range to be modified. Notes to temperature range limit – Do not select the limits greater than needed. – Observe the characteristics of the thermal fluid (viscosity, flashpoint). – Consider the defaults of your application’s manufacturer. The programs for operating the thermostat are described in Chapter 4 of the Operating Instructions. 28
4. Thermoregulation via <strong>Control</strong>ler At work
Page 1: Version 2.0 /08 Compatible Control
Page 4 and 5: Preface Dear Customer, Congratulati
Page 6 and 7: Unichiller with Compatible Control
Page 9: Contents Preface 1. Safety 1.1 Inte
Page 12 and 13: 1. Safety 1.1 Intended Use General
Page 15 and 16: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Page 17 and 18: 1 2 3 4 5 6 7 8 Removable, exchange
Page 19 and 20: 1 2 3 4 5 6 7 8 9 Removable, exchan
Page 21: 3. Commissioning
Page 24 and 25: DIN 12876 3. Commissioning 3.1 Safe
Page 26 and 27: Hazards through emission of fluids
Page 28 and 29: Preparing the thermostat for use Th
Page 30 and 31: Overtemperature protection Requirem
Page 32 and 33: Fill the bath 3. Commissioning 3.4
Page 34 and 35: Fill the thermostat 3. Commissionin
Page 39 and 40: Checks to be performed: Test Arrang
Page 41 and 42: Selection 4. Thermoregulation via C
Page 43 and 44: Display Time Scale Mains Failure Au
Page 45 and 46: Compressor Auto Heating Capacity So
Page 47 and 48: Analog Interface Caution! Electroni
Page 49 and 50: Digital Interface 4. Thermoregulati
Page 51 and 52: Acoustic Alarm Select Usermenu Conf
Page 53 and 54: Calibra- tion Prog. 4. Thermoregula
Page 55 and 56: Circulation Venting 2. Setpoint 4.
Page 57 and 58: Start Ramp 4. Thermoregulation via
Page 59 and 60: Edit Program 4. Thermoregulation vi
Page 61 and 62: Edit Program 4. Thermoregulation vi
Page 63: Abort Schematic diagram See 2.3. 4.
Page 67 and 68: Draining Thermofluid Draining cooli
Page 69 and 70: Requirements Replacing fuses Cleani
Page 71: 6. Appendix
Page 74 and 75: Interface Specification Float Switc
Page 76 and 77: Hardware error ALARM !!! HARDWARE E
Page 78 and 79: 6. Appendix 6.3. Device Messages 2.
Page 80 and 81: Bath Volume (also referred to as fi
Page 82 and 83: Flow Temperature Denotes the temper
Page 84 and 85: Process Temperature (core temperatu
Page 86:
Viscosity Also referred to as „in
show all

Compatible Control - HUBER

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?