5000 Series Indicators Instruction Manual - MaRCo

More documents

Recommendations

Info

EN-10 5000 Series Indicators 1. Control Functions TABLE 1-5. CONTROL FUNCTIONS. Button Primary Function (Short Press) ON/ZERO Turns the Indicator PRINT Sends the current value FUNCTION Initiates an application TARE Performs a tare on. to the selected COM mode. operation. ports if AUTOPRINT is If Indicator is On, sets set to Off. Temporarily displays the zero. active mode’s reference data. Secondary Function (Long Press) Off Turns the Indicator off. Units Changes the weighing Mode Allows changing the Menu-Cal Enter the User menu. Unit. application mode. Press and hold allows scrolling through modes. Menu Function (Short Press) Yes Accepts the current No Advances to the next Back Moves Back to previous Exit Exits the User menu. setting on the display. menu or menu item. menu item. Aborts the calibration in Rejects the current Decrements the value. progress. setting on the display and advances to the next available setting. Increments the value.
5000 Series Indicators EN-11 2. INSTALLATION 2.1 Unpacking Unpack the following items: • T51P or T51XW Indicator • AC Power Cord (T51P only) • Mounting Bracket • Knobs (2) 2.2 External Connections • Capacity Label Sheet • LFT Sealing kit • Instruction Manual CD • Warranty Card 2.2.1 Scale Base with Connector to T51P Ohaus bases with a connector can be attached to the external load cell connector (Figure 1-1, item 14). Refer to section 2.3.2 for bases without a connector. 2.2.2 RS232 interface Cable to T51P Connect the optional RS232 cable to the RS232 connector (Figure 1-1, item 16). Pin Connection 1 N/C 2 TXD 3 RXD 4 N/C 5 GND 6 N/C 7 CTS 8 RTS 9 N/C 5 4 3 2 1 9 8 7 6 Figure 2-1. RS232 Pins. 2.2.3 AC Power to T51P Connect the AC power cord (supplied) to the power receptacle (Figure 1-1, item 11), then connect the AC plug to an electrical outlet. 2.2.4 AC Power to T51XW Connect the AC plug to a properly grounded electrical outlet. 2.2.5 Battery Power to T51P The indicator can be operated on alkaline batteries (not supplied) when AC power is not available. It will automatically switch to battery operation if there is power failure or the power cord is removed. The indicator can operate for up to 80 hours on battery power. Remove the battery cover (Figure 1-1, item 9) and install 6 C-type (LR14) alkaline batteries in the orientation specified. Re-install the battery cover. During battery operation, the battery charge symbol indicates the battery status. The indicator will automatically turn-off when the batteries are fully discharged.
Page 1 and 2: 5000 Series Indicators Instruction
Page 3 and 4: 5000 Series Indicators EN- TABLE OF
Page 5 and 6: 5000 Series Indicators EN- TABLE OF
Page 7 and 8: 5000 Series Indicators EN- 1. INTRO
Page 9 and 10: 5000 Series Indicators EN- 1. Overv
Page 11: 5000 Series Indicators EN- 1. Overv
Page 15 and 16: 5000 Series Indicators EN-13 2.3. R
Page 17 and 18: 5000 Series Indicators EN-15 3.1 Me
Page 19 and 20: 5000 Series Indicators EN-17 3.3.1
Page 21 and 22: 5000 Series Indicators EN-19 3.3. C
Page 23 and 24: 5000 Series Indicators EN-21 3. Set
Page 25 and 26: 5000 Series Indicators EN-23 3.4. A
Page 33 and 34: 5000 Series Indicators EN-31 3.8. D
Page 35 and 36: 5000 Series Indicators EN-33 3. Pri
Page 37 and 38: 5000 Series Indicators EN-35 Projec
Page 41 and 42: 5000 Series Indicators EN-39 3.11.
Page 47 and 48: 5000 Series Indicators EN-45 4. Cha
Page 49 and 50: 5000 Series Indicators EN-47 4.8. C
Page 51 and 52: 5000 Series Indicators EN-49 5 SERI
Page 53 and 54: 5000 Series Indicators EN-51 Check
Page 55 and 56: 5000 Series Indicators EN-53 7 MAIN
Page 57 and 58: 5000 Series Indicators EN-55 8. TEC
Page 59 and 60: 5000 Series Indicators EN-57 8. Dra
Page 61 and 62: 5000 Series Indicators EN-59 Import
Page 64 and 65:
Ohaus Corporation 19A Chapin Road P
Page 66 and 67:
Compliance This product conforms to
Page 68 and 69:
EN-2 Defender Series Base Selecting
Page 70 and 71:
EN-4 Defender Series Base TABLE 2.3
Page 72 and 73:
EN-6 Defender Series Base Drawings
Page 76 and 77:
Ohaus Corporation 19A Chapin Road P
Page 78:
OVERVIEW OF CONTROLS AND FUNCTIONS
show all

5000 Series Indicators Instruction Manual - MaRCo

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?