Display Function - Marine Autopilots, Engine Controls and Instruments
Display Function - Marine Autopilots, Engine Controls and Instruments
Display Function - Marine Autopilots, Engine Controls and Instruments
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Secondary <strong>Function</strong>s:<br />
The Secondary <strong>Display</strong> <strong>Function</strong>s can be<br />
accessed by holding the SELECT button for<br />
two seconds for the first function, <strong>and</strong> then by<br />
briefly pressing it for the succeeding functions.<br />
The last Secondary <strong>Function</strong> is followed by<br />
the first Primary <strong>Display</strong> <strong>Function</strong>.<br />
<br />
SELECT<br />
<br />
Magnetic Wind<br />
This function requires<br />
a heading<br />
sensor in the system.<br />
The magnetic<br />
wind direction or true<br />
wind speed can be<br />
selected alternately<br />
with the right button.<br />
The analogue<br />
LED shows the relative<br />
angle of true<br />
wind.<br />
Sensor Warning<br />
Dashes on the LCD are<br />
an indication that valid<br />
signals are not received<br />
from the sensor<br />
(or the wind vane<br />
sits at zero degrees<br />
<br />
SELECT<br />
<br />
Settings<br />
for a prolonged period).<br />
Check also, that<br />
the configuration of<br />
the display with the<br />
wind sensor physically<br />
connected is SE=06 or 07 (n0=01 or 02 for<br />
the PB100/200 wind sensor).<br />
Tecnautic Wind Vane Correction<br />
This correction<br />
has to be done at a<br />
display unit with the<br />
wind sensor physically<br />
connected <strong>and</strong><br />
the sensor type<br />
number correctly<br />
configured <strong>and</strong> the<br />
apparent wind function<br />
displayed.<br />
SELECT <br />
Warnings<br />
LCD blinking<br />
VMG<br />
This is the part of<br />
the boat speed in<br />
direction of the true<br />
wind vector, either<br />
upwind or downwind.<br />
The analogue LED<br />
shows the relative<br />
true wind angle.<br />
Low Battery Alarm<br />
The battery alert<br />
comes on when the<br />
supply voltage has<br />
dropped below 10<br />
Volts. It disappears<br />
only after voltage has<br />
increased above 11<br />
Volts. The display<br />
stops working below<br />
9 Volts.<br />
The wind angle can be corrected by altering<br />
the correction "C".<br />
1. Select the wind function, then press both<br />
arrow buttons briefly at the same time.<br />
2. Use the right button to increase a starboard<br />
wind angle or to decrease a port wind<br />
angle.<br />
Use the left button to increase a port wind<br />
angle or to decrease a starboard wind angle.<br />
3. Exit the function with the middle button.<br />
PB100/200 Wind Sensor<br />
The compass alignment function of the<br />
PB100/200 will also align the wind angle.<br />
Illumination<br />
If you have a dimmer installed in the system,<br />
use only the dimmer.<br />
Otherwise use the<br />
push buttons for illumination<br />
control:<br />
1. Press <strong>and</strong> hold<br />
all three buttons.<br />
<br />
SELECT<br />
2. Release<br />
SELECT button first,<br />
then the others.<br />
3. Adjust brightness<br />
with left or right button.<br />
All other displays with the same group<br />
number will follow in brightness.<br />
4. Exit from the function with the SELECTbutton.<br />
11