Display Function - Marine Autopilots, Engine Controls and Instruments
Display Function - Marine Autopilots, Engine Controls and Instruments
Display Function - Marine Autopilots, Engine Controls and Instruments
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Secondary <strong>Function</strong>s:<br />
The Secondary <strong>Display</strong> <strong>Function</strong>s can be<br />
accessed by holding the SELECT button for<br />
two seconds for the first function, <strong>and</strong> then by<br />
briefly pressing it for the succeeding functions.<br />
The last Secondary<br />
<strong>Function</strong> is followed by<br />
the first Primary <strong>Display</strong><br />
<strong>Function</strong>.<br />
<br />
SELECT<br />
Depth Units<br />
The left or right<br />
button is used to select<br />
the desired units<br />
(meters or feet).<br />
Illumination<br />
If you have a dimmer installed in the system,<br />
use only the dimmer.<br />
Otherwise use the<br />
push buttons for illumination<br />
control:<br />
1. Press <strong>and</strong> hold<br />
all three buttons.<br />
2. Release<br />
<br />
SELECT<br />
SELECT button first,<br />
then the others.<br />
3. Adjust brightness<br />
with left or right<br />
button.<br />
All other displays with the same group<br />
number will follow in brightness.<br />
4. Exit from the function with the SELECTbutton.<br />
Sensor-Frequency<br />
Only with Echo-Box-2<br />
<strong>and</strong> only on the <strong>Display</strong><br />
Unit set to n0=05 (<strong>and</strong> to<br />
which the Echo-Box2 is<br />
physiclly connected).<br />
This function follows<br />
in sequence<br />
after the Depth Units<br />
SELECT<br />
function above.<br />
The transducer<br />
frequency can be selected<br />
with the left or<br />
right button. Set the same<br />
number as marked on the<br />
transducer cable (Important for good transducer<br />
function!)<br />
<br />
Settings:<br />
Depth offset to keel or surface<br />
1. Select depth display<br />
2. Press <strong>and</strong> hold<br />
both arrow buttons for<br />
two seconds.<br />
With a zero correction<br />
setting (c 0.0),<br />
<br />
SELECT<br />
depth is measured<br />
from the sensor location.<br />
A positive value<br />
of "c" will be added to<br />
the sensed depth (used for<br />
depth below surface indication), a negative "c“<br />
will be subtracted from the sensed depth<br />
(used for depth below keel).<br />
To alter the correction, press left or right<br />
button repeatedly.<br />
Exit this function with the middle button.<br />
Warnings:<br />
<br />
SELECT<br />
Dashes on the<br />
display:<br />
means no echo<br />
received. The reason<br />
could be depth exceeding<br />
the range or<br />
excessive sound absorption<br />
in the water,<br />
at the bottom (or in the<br />
hull in case of a within<br />
hull installation).<br />
If the Echo-Box does not communicate with<br />
the display, there will also be dashes on the<br />
LCD. Check the correct configuration of the<br />
display with the Echo-Box physically connected<br />
(n0:04 for Echo-Box-1 or n0:05 for Echo-<br />
Box-2 in the NMEA setup).<br />
Low Battery Alarm<br />
The battery alert<br />
comes on when the<br />
supply voltage has<br />
dropped below 10<br />
Volts. It disappears<br />
only after voltage has<br />
increased above 11<br />
Volts. The display<br />
stops working below 9<br />
Volts.<br />
13