USER'S GUIDE - Neopost

More documents

Recommendations

Info

Safety Precautions • Only competent, trained personnel should operate this system. If non-trained personnel do operate this system, the manufacturer will not accept responsibility for any resulting accidents or injuries. • Only skilled persons, who are aware of the risks involved, may open the protective covers. For safety reasons, the system will not function when the covers are open. • Keep long hair, fingers, jewelry, etc. away from rotating and moving parts. • The power connection must be easily accessible, preferably close to the system. For safety reasons, it is essential that the system is connected to a socket outlet that has a protective earth (ground) connection. • Overcurrent protection in the equipment also relies on the branch circuit protection (max. 20 A). • The following part(s) is (are) considered the equipment disconnect device(s): - Power supply cord plug or appliance coupler. - 12-pole connector, located on the right-hand side. 1 English CAUTION: DOUBLE POLE / NEUTRAL FUSING (this means that after operating of the fuse, parts of the equipment that remain energized, might represent a hazard during servicing.) Precaution The general process of automated document handling can sometimes create a build up of static electricity. Therefore we recommend that the following measures are taken to reduce the side effects of any electrostatic charge. • Make sure that you operate the system within the recommended temperature and humidity conditions. • Make use of antistatic mats where appropriate. • If necessary, make use of an ionizer to reduce static charge build up in the room where the system is located. Please contact your supplier for further information. 3
1 English Country Specific Conditions Denmark In Denmark, certain types of Class 1 appliances may be provided with a plug that does not provide an adequate earth (ground) connection when inserted into a Danish socket outlet. Make sure the system has a good functioning connection that has protective earthing (the plug and socket outlet must match). Japan • Establish an earth (ground) connection before connecting the mains plug to the power supply. • First disconnect the power supply before removing the earth (ground) connection. 4
Page 1 and 2: DS-90 DS-35 USER’S GUIDE
Page 3 and 4: Adjusting the HCDF Side Guides.....
Page 5 and 6: Introduction.......................
Page 8 and 9: 1 Warning Read this First 1 About t
Page 12 and 13: End of Life The objectives of the E
Page 14 and 15: 2 English The figure shows an overv
Page 16 and 17: Operating Controls 2 English A - ca
Page 18 and 19: Installing the Document Feed Trays
Page 20 and 21: Home Menu 2 When you start up the s
Page 22 and 23: • A picture of the system with sy
Page 24 and 25: Document Orientation 2 English In c
Page 26 and 27: Loading Envelopes Before you load t
Page 28 and 29: 2. Fill the reservoir A to the "Max
Page 30 and 31: Adjusting the MaxiFeeder Side Guide
Page 32 and 33: Feeding documents (MaxiFeeder) To f
Page 34 and 35: 3. Rotate wheel E. The space betwee
Page 36 and 37: Installing the VersaFeeder When ins
Page 38 and 39: Adjusting the Document Separation (
Page 40 and 41: Support for Curved Reply Envelopes
Page 42 and 43: High Capacity Envelope Hopper (EF-4
Page 44 and 45: High Capacity Conveyor Belt (CS-2)
Page 46 and 47: insert'n Frank / insert'n Mail If t
Page 48 and 49: 4 Processing Mail Sets Introduction
Page 50 and 51: Processing a mail set with BRE or i
Page 52 and 53: Adjustment of the Document Stoppers
Page 54 and 55: 8. When finished with Daily Mail, p
Page 56 and 57: Verifying the Insert Position To ma
Page 58 and 59: 2. Press [Manual] to create a new j
Page 60 and 61:
2. Select the job you want to use.
Page 62 and 63:
Using a job If you want to use an e
Page 64 and 65:
3. Press the [Job] menu button. The
Page 66 and 67:
4. Press the [Delete job] button. T
Page 68 and 69:
Document settings In the ‘documen
Page 70 and 71:
When a feeder is selected for readi
Page 72 and 73:
• Stop on misread: define if the
Page 74 and 75:
Job name It is possible to store th
Page 76 and 77:
• Select the button if you want t
Page 78 and 79:
• Select the button if you want t
Page 80 and 81:
Mail Piece Production Control setti
Page 82 and 83:
• System info (see Viewing System
Page 84 and 85:
Viewing System info and Software ve
Page 86 and 87:
Activating an option To add a licen
Page 88 and 89:
3. In the Hardware test menu, press
Page 90 and 91:
2. Use the arrows next to "Flap Clo
Page 92 and 93:
2. Use the arrows next to "Document
Page 94 and 95:
7 Reading Introduction The reading
Page 96 and 97:
Document Orientation Switch on the
Page 98 and 99:
BCR basic license For the BCR basic
Page 100 and 101:
4. In the BCR settings screen, conf
Page 102 and 103:
OMR Code Description Position of th
Page 104 and 105:
OMR advanced license For the OMR ad
Page 106 and 107:
An Example of OMR Code In the figur
Page 108 and 109:
2-track OMR 2-track OMR uses two OM
Page 110 and 111:
Start-up Online Services To start-u
Page 112 and 113:
2. Press the button to view details
Page 114 and 115:
4. In case of a new job: Press the
Page 116 and 117:
Selecting the country To select a c
Page 118 and 119:
9 Operator Maintenance Maintenance
Page 120 and 121:
Resetting Photocells To calibrate a
Page 122 and 123:
Clearing Stoppages Stoppages can oc
Page 124 and 125:
4. Release lever A. 5. Make sure th
Page 126 and 127:
flexFeed When a stoppage occurs in
Page 128 and 129:
4. Close the feed unit: - Place you
Page 130 and 131:
System stops while inserting (stopp
Page 132 and 133:
11Specifications Technical Specific
Page 134 and 135:
Envelope sizes Envelope quality Sta
Page 136 and 137:
versaFeeder Specifications Model Ty
Page 138 and 139:
High Capacity Conveyor Belt Specifi
Page 140 and 141:
C-fold Fold type in which a documen
Page 142 and 143:
Flexcode OMR flexFeed High Capacity
Page 144 and 145:
V-fold A V-fold implies the documen
Page 146 and 147:
Note: this equipment has been teste
Page 148 and 149:
Page 150 and 151:
show all

USER'S GUIDE - Neopost

Create successful ePaper yourself

Delete template?

Save as template?