USER'S GUIDE - Neopost

More documents

Recommendations

Info

Feeding documents (MaxiFeeder) To feed documents: When filling the maxiFeeder, make sure that the document/BREs are positioned parallel in relation to the feed plate to ensure correct feeding. The feeding plate assembly will be shifted up automatically (when the system starts processing) until documents/BREs are underneath the rubber paper pullers. 1. Squeeze the two blue handles A and B. 3 English 2. Shift the feeding plate C to the rear position. 3. Loosen the stack of documents and place them in the feeder. BREs with flap down and leading (top side pointing to system). High Capacity Document Feeder (HCDF) The High Capacity Document Feeder is an option that can be delivered from factory, or added to a 2 or 4 station version by a service engineer. The High Capacity Document Feeder has a capacity for up to 725 sheets. The normal document feeder tray has a capacity of 325 sheets. 25
Installing the HCDF To install the feeder tray of the HCDF: 3 English 1. Pull down lever A. 2. Hook in the feeder tray. 3. Release lever A. Adjusting the HCDF Side Guides To adjust the side guides B: 1. Loosen the knob D half a turn. 2. Put a small stack of documents between the side guides. 26
Page 1 and 2: DS-90 DS-35 USER’S GUIDE
Page 3 and 4: Adjusting the HCDF Side Guides.....
Page 5 and 6: Introduction.......................
Page 8 and 9: 1 Warning Read this First 1 About t
Page 10 and 11: Safety Precautions • Only compete
Page 12 and 13: End of Life The objectives of the E
Page 14 and 15: 2 English The figure shows an overv
Page 16 and 17: Operating Controls 2 English A - ca
Page 18 and 19: Installing the Document Feed Trays
Page 20 and 21: Home Menu 2 When you start up the s
Page 22 and 23: • A picture of the system with sy
Page 24 and 25: Document Orientation 2 English In c
Page 26 and 27: Loading Envelopes Before you load t
Page 28 and 29: 2. Fill the reservoir A to the "Max
Page 30 and 31: Adjusting the MaxiFeeder Side Guide
Page 34 and 35: 3. Rotate wheel E. The space betwee
Page 36 and 37: Installing the VersaFeeder When ins
Page 38 and 39: Adjusting the Document Separation (
Page 40 and 41: Support for Curved Reply Envelopes
Page 42 and 43: High Capacity Envelope Hopper (EF-4
Page 44 and 45: High Capacity Conveyor Belt (CS-2)
Page 46 and 47: insert'n Frank / insert'n Mail If t
Page 48 and 49: 4 Processing Mail Sets Introduction
Page 50 and 51: Processing a mail set with BRE or i
Page 52 and 53: Adjustment of the Document Stoppers
Page 54 and 55: 8. When finished with Daily Mail, p
Page 56 and 57: Verifying the Insert Position To ma
Page 58 and 59: 2. Press [Manual] to create a new j
Page 60 and 61: 2. Select the job you want to use.
Page 62 and 63: Using a job If you want to use an e
Page 64 and 65: 3. Press the [Job] menu button. The
Page 66 and 67: 4. Press the [Delete job] button. T
Page 68 and 69: Document settings In the ‘documen
Page 70 and 71: When a feeder is selected for readi
Page 72 and 73: • Stop on misread: define if the
Page 74 and 75: Job name It is possible to store th
Page 76 and 77: • Select the button if you want t
Page 78 and 79: • Select the button if you want t
Page 80 and 81: Mail Piece Production Control setti
Page 82 and 83:
• System info (see Viewing System
Page 84 and 85:
Viewing System info and Software ve
Page 86 and 87:
Activating an option To add a licen
Page 88 and 89:
3. In the Hardware test menu, press
Page 90 and 91:
2. Use the arrows next to "Flap Clo
Page 92 and 93:
2. Use the arrows next to "Document
Page 94 and 95:
7 Reading Introduction The reading
Page 96 and 97:
Document Orientation Switch on the
Page 98 and 99:
BCR basic license For the BCR basic
Page 100 and 101:
4. In the BCR settings screen, conf
Page 102 and 103:
OMR Code Description Position of th
Page 104 and 105:
OMR advanced license For the OMR ad
Page 106 and 107:
An Example of OMR Code In the figur
Page 108 and 109:
2-track OMR 2-track OMR uses two OM
Page 110 and 111:
Start-up Online Services To start-u
Page 112 and 113:
2. Press the button to view details
Page 114 and 115:
4. In case of a new job: Press the
Page 116 and 117:
Selecting the country To select a c
Page 118 and 119:
9 Operator Maintenance Maintenance
Page 120 and 121:
Resetting Photocells To calibrate a
Page 122 and 123:
Clearing Stoppages Stoppages can oc
Page 124 and 125:
4. Release lever A. 5. Make sure th
Page 126 and 127:
flexFeed When a stoppage occurs in
Page 128 and 129:
4. Close the feed unit: - Place you
Page 130 and 131:
System stops while inserting (stopp
Page 132 and 133:
11Specifications Technical Specific
Page 134 and 135:
Envelope sizes Envelope quality Sta
Page 136 and 137:
versaFeeder Specifications Model Ty
Page 138 and 139:
High Capacity Conveyor Belt Specifi
Page 140 and 141:
C-fold Fold type in which a documen
Page 142 and 143:
Flexcode OMR flexFeed High Capacity
Page 144 and 145:
V-fold A V-fold implies the documen
Page 146 and 147:
Note: this equipment has been teste
Page 148 and 149:
Page 150 and 151:
show all

USER'S GUIDE - Neopost

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?