1969 Camaro Firebird - Classic Auto Air

More documents

Recommendations

Info

PAGE 18 THESE ARE THE PARTS YOU WILL FIND IN BAG KIT C You will use all of these parts and hardware during the next series of installation steps. Clear Plastic Drain Tube Electronic Water Control Valve PN#16-1081-2 Six Worm Gear Clamps Refrigerant Tape Firewall Block Off PN#10-2056-1 Six #10 - 16 x 3/4" Tek Screws Illustrations NOT shown actual size www.classicautoair.com • 866.435.7801
PAGE 19 It may be necessary to manipulate the tubes slightly to get proper fittment thru the block-off plate In Bag Kit C you’ll find the firewall block off. Install this over the hose connections coming thru the firewall within the engine compartment (you’ll need to loosen your hood hinge and tuck one corner behind it). Attach with six #10 - 16 x 3/4" Tek screws. TIP: This would be a good time to “jump” ahead a bit, and remove the ORANGE cable from Bag Kit D and route it thru the block off plate (it will be plugged into the electronic water valve). The cable for the electronic water valve can share the hole with smaller liquid line opening. Seal around the tubes with the included refrigerant tape. This will keep unwanted moisture and debris from entering thru the IMPORTANT NOTICE: PROPER INSTALLATION OF WATER VALVE INSTRUCTIONS!!! Classic Auto Air has done extensive testing on the correct method to install the water valve in order to get a repeatable and progressive temperature control. Your water valve MUST be installed per these instructions!... (if not, your system will not work properly... and that’s an absolute fact). The lower connection on the tubes coming thru the block off assembly is going to be routed to the water outlet on the intake manifold. Attach your hose with cable clamps on both ends and route where it will not interfere with linkage or come in contact with exhaust manifolds or headers. HEATER CORE FOLLOW THESE TAGS... CHECK IT TWICE BEFORE PROCEEDING! WATER PUMP The upper port coming thru the firewall will be routed to and thru your new your electronic water valve (the water valve is marked for easy installation). First Attach a 6” piece of 5/8” dia. heater hose with the supplied worm gear clamp. Attach to the inlet side of the water valve using another supplied hose clamp. Attach a heater hose from the outlet side of the electronic water valve and route to the connection on the water pump. Insert a 6" piece of the clear, 1/2" drain tube we included through the hole previously drilled and attach over the drain nipple. Seal around tube with refrigerant tape. www.classicautoair.com • 866.435.7801
Page 1: © 1969 Camaro Factory Air 1969-74
Page 4 and 5: PAGE 4 Check List, Pre-Installation
Page 6 and 7: PAGE 6 Control & Operating Instruct
Page 8 and 9: PAGE 8 BAG A (CONTROLS) CONTENTS (v
Page 10 and 11: PAGE 10 Preparing the TEMP EZ Cable
Page 12 and 13: PAGE 12 THESE ARE THE PARTS YOU WIL
Page 14 and 15: PAGE 13 Within the engine compartme
Page 16 and 17: PAGE 15 Locate in the UPPER MOUNTIN
Page 22 and 23: PAGE 22 Wiring Diagram/Overview To
Page 26 and 27: PAGE 26 Remove all of the original
Page 28 and 29: PAGE 28 You can reinstall the glove
Page 30 and 31: PAGE 32 DRIER AND CONDENSER PREPARA
Page 32 and 33: PAGE 34 Time to install the compres
Page 34 and 35: PAGE 36 www.classicautoair.com •
Page 36 and 37: PAGE 38 TEST CONDITIONS USED TO DET
Page 39: 1969 Factory Air Template DRILL 7/8
Page 44: IF YOU PRINTED THIS MANUAL PLEASE R

1969 Camaro Firebird - Classic Auto Air

Create successful ePaper yourself

Delete template?

Save as template?