Datasheet - PMCCatalogue

More documents

Recommendations

Info

CHANGING THE FILTER ELEMENT ON LMP 952/953/954/955/956 FILTERS 1 Depressurise the system and clean the filter. 2 Unscrew the air breather plug (pos. A) and open the oil drain connection (pos. B, pos. B1 when the rapid oil drain flange is present) collecting the fluid in a suitable container. When the operation is terminated screw down the plug (pos. A) tightening it fully down after having checked the condition of its seal. Close the oil drain connection (B). Fig. 3 C 7 Lubricate the filter element seal with the operating fluid. Insert the cartridge in the head spigot or insert the upper spigot into the element. A B A B1 B Fig. 1 Fig. 4 3 Unscrew the cover using the specific tools and tools, extract the upper spigot, and extract the filter element. 4 Collect the spent oil and cartridge in a suitable container and dispose of them in compliance with statutory legislation. 8 Screw the cover onto the housing using the correct tool. WARNING: Screw fully home on the housing “DO NOT APPLY EXCESSIVE TIGHTENING TORQUE”. A A Fig. 2 !!! WARNING !!! 5 To avoid damaging the components clean seal (B), surfaces (A) and threads (C) of the cover and the housing. 6 Check the condition of seals (B) - if renewing, lubricate the new seals with the operating fluid before installing. Fig. 5 9 Repeat the steps from point “2” on the other filters. Now start the machine and bleed the air by unscrewing (max. one turn) the plugs (pos. A). When the operation is terminated tighten the plugs fully. 10 Start the machine and check for the absence of leaks. Repeat the check when the machine has reached its operating temperature. 1 0 9
CHANGING THE FILTER ELEMENT ON LMD 951 FILTERS Indication of the lever position referred to the flow. As shown on the filter handle. When the operation is terminated screw down the plug (pos. A) tightening it fully down after having checked the condition of its seal. Close the oil drain connection (B). FILTER A A C B FILTER B Filter A B Filter B Fig. 1 Fig. 3 1 B e f o re rotating the lever from the filter B position to filter A, open the balancing valve (pos. C) by turning it counterclockwise. Bleed the air by means of the plug (pos. D), which must be turned through a maximum of one revolution. After bleeding the air tighten the breather plug and close the balancing valve (pos. C) by turning it clockwise. 4 Open the balancing valve (pos. C) by turning it counterclockwise. Bleed the air through the plug (pos. A) which must be turned through a maximum of one revolution. After bleeding the air refit the breather plug and close the balancing valve (pos. C) by turning it clockwise. D C C A Filter A Filter B Filter A Filter B Fig. 2 Fig. 4 2 Tu rn the lever to divert the oil flow from filter B to filter A. Loosen the oil drain plug (pos. B) to depre s- surise the filter, unscrew the air breather plug (pos. A) and open the oil drain connection (pos. B) or fro m the opposite part of the head - collecting the fluid in a suitable container. 5 Check for the absence of leaks. Filter “B” is set up for use. 1 1 0
Page 1 and 2:
SERIES INLINE FILTERS LMP Maximum p
Page 3 and 4:
Index Head at top In-line connectio
Page 5 and 6:
Hydraulic schematics HYDRAULIC SCHE
Page 7 and 8:
Multipass test in compliance with n
Page 9 and 10:
Data for sizing multicartridge filt
Page 11 and 12:
1 3 Order code Order code 1 2 3 4 1
Page 13 and 14:
STYLE TECHNICAL CHARACTERISTICS SER
Page 15 and 16:
STYLE TECHNICAL CHARACTERISTICS SER
Page 17 and 18:
2 0 LMP 210
Page 19 and 20:
Technical data Filter housing ( M a
Page 21 and 22:
LMP 210 spare parts 3 c 3 d 4 3 a 1
Page 23 and 24:
2 6 LMP 400 - 401 430 - 431
Page 25 and 26:
Technical data Filter h o u s i n g
Page 27 and 28:
Dimensions LMP 400 LMP 401 Length 2
Page 29 and 30:
LMP 430 LMP 431 Length 5 - 6 Length
Page 31 and 32:
LMP400/401 spare parts Length 2, 3,
Page 33 and 34:
LMP430/431 spare parts Length 5, 6
Page 35 and 36:
3 8 LMD 400 - 401 431
Page 37 and 38:
Technical data Filter h o u s i n g
Page 39 and 40:
Dimensions LMD 400 LMD 400 Length 4
Page 41 and 42:
LMD 431 Length 5 - 6 I F Ve r s i o
Page 43 and 44:
LMD 400 spare parts 3 4 b 4 b 1 5 a
Page 45 and 46:
LMD 431 spare parts 1 6 4 a 7 4 b 3
Page 47 and 48:
4 8 LMP 900-901
Page 49 and 50:
Technical data Filter housing ( M a
Page 51 and 52:
Dimensions LMP 900 LMP 901 Length 1
Page 53 and 54: LMP900/901 spare parts Length 1 4 4
Page 55 and 56: Filter assembly LMP LMP 900/901 ord
Page 57 and 58: SERIES LMP 902-903 Working pressure
Page 59 and 60: Recommended maximum flow rate - Pre
Page 61 and 62: LMP 902 6 4 5 1 6 0 3 0 0 1 8 5 LMP
Page 63 and 64: LMP902/903 ordering information Fil
Page 65 and 66: SERIES LMP 950-951 Working pressure
Page 67 and 68: Valves Bypass valve pressure drop L
Page 69 and 70: LMP 950/951 spare parts Length 2 -
Page 71 and 72: 7 4 LMP 952÷956
Page 73 and 74: Technical data Filter housing ( M a
Page 75 and 76: Manifolds Position of manifolds IN
Page 77 and 78: LMP 952 LMP 954 1 6 0 3 0 0 6 4 5 1
Page 79 and 80: O p t i o n Flange with oil drain p
Page 81 and 82: LMP952÷956 ordering information Fi
Page 83 and 84: SERIES LMD 951 Working pressure 16
Page 85 and 86: Recommended maximum flow rate - Pre
Page 87 and 88: LMD 952 L A A H I D C Ve r s i o n:
Page 89 and 90: LMD 951 LMD 952 - 953 D C B A A B A
Page 91 and 92: LMD 952-953 spare parts 1 7 6 7 2 5
Page 93 and 94: FIXING SYSTEMS FOR LMP 400-900 LMP
Page 95 and 96: Operating & Maintenance Manual In-l
Page 97 and 98: CHANGING THE FILTER ELEMENT IN LMP
Page 99 and 100: CHANGING THE FILTER ELEMENT ON LMP
Page 101 and 102: CHANGING THE FILTER ELEMENT ON LMP
Page 103: CHANGING THE FILTER ELEMENT ON LMP
show all

Datasheet - PMCCatalogue

Create successful ePaper yourself

Delete template?

Save as template?