Download Prodigy Instruction Manual PDF file - Raynor Garage Doors

More documents

Recommendations

Info

Adjustment 5 If your cable tension monitor has been activated the LED on the garage door opener will blink 9 times. 6 1. With the door fully closed, the power door lock bolt should be protruding through the track. 2. Operate the door in the open direction. The power door lock should retract before the door begins to move. 3. Operate the door in the down direction. When the door reaches the fully closed position, the power door lock should automatically activate to secure the door. 7 Test Cable Tension Monitor Test Power Door Lock NOTE: If the power door lock does not function, the lock can be manually released by sliding the manual release handle to the open position. To Open the Door Manually Disengage door lock before proceeding. The door should be fully closed if possible. Pull down on the emergency release handle until a click noise is heard from the garage door opener and lift the door manually. To reconnect the door to the garage door opener, pull the emergency release handle straight down a second time until a click noise is heard from the garage door opener. The door will reconnect on the next UP or DOWN operation. Test the emergency release: 1. Make sure the garage door is closed. 2. Pull the emergency release handle. The garage door should then be able to be opened manually. 3. Return the door to the closed position. 4. Pull the emergency handle a second time. 5. Reconnect the door to the garage door opener. LED Emergency Release Handle 22 Power Door Lock To prevent possible SERIOUS INJURY or DEATH from a falling garage door: • If possible, use emergency release handle to disengage door ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly. • NEVER use emergency release handle unless garage doorway is clear of persons and obstructions. Manual Release Lock Bolt “Locked”
WARNING Operation IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with door control push buttons or remote controls. 3. ONLY activate door when it can be seen clearly, it is properly adjusted and there are no obstructions to door travel. 4. ALWAYS keep garage door in sight and away from people and objects until completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. 5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPENED DOOR. 6. If possible, use emergency release handle to disengage door ONLY when door is CLOSED. Use caution when using this release with the door open. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly and increasing the risk of SEVERE INJURY or DEATH. 7. NEVER use emergency release handle unless doorway is clear of persons and obstructions. 8. After ANY adjustments are made, the safety reversal system MUST be tested. Failure to adjust the garage door opener properly may cause SEVERE INJURY or DEATH. 9. Safety reversal system MUST be tested every month. Door MUST reverse on contact with 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor. Failure to adjust the garage door opener properly may cause SEVERE INJURY or DEATH. 10. ALWAYS KEEP DOOR PROPERLY BALANCED (see page 4). An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH. 11. ALL repairs to cables, spring assemblies and other hardware, ALL of which are under EXTREME tension, MUST be made by a trained door systems technician. 12. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. 13. This operator system is equipped with an unattended operation feature. The door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. 14. SAVE THESE INSTRUCTIONS. Using Your Garage Door Opener Your garage door opener has already been programmed at the factory to operate with your remote control, which changes with each use, randomly accessing over 100 billion new codes. MyQ ® technology uses a 900MHz signal to provide two-way communication between the garage door opener and MyQ ® enabled accessories. When programmed to the MyQ ® Internet Gateway you can monitor and control your garage door from any internet enabled computer or smartphone. You may program up to 12 Security✚ 2.0 remote controls, 2 Security✚ 2.0 keyless entries and a combination of 16 MyQ ® accessories to the MyQ ® control panel. The garage door opener can be activated through a wall-mounted door control, remote control, wireless keyless entry or MyQ ® accessory. When the door is closed and the garage door opener is activated the door will open. If the door senses an obstruction or is interrupted while opening the door will stop. When the door is in any position other than closed and the garage door opener is activated the door will close. If the garage door opener senses an obstruction while closing, the door will reverse. If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times. However, you can close the door if you hold the button on the door control or keyless entry until the door is fully closed. The safety reversing sensors do not affect the opening cycle. The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. The garage door opener lights will turn on when the garage door opener is activated. They will turn off automatically after 4-1/2 minutes or provide constant light when the Light feature on the MyQ ® Control Panel is activated. Bulb size is A19. Bulb power is 100 watts maximum. Light feature: Lights will also turn on when someone walks through the open garage door. With a MyQ ® Control Panel, this feature may be turned off as follows: With the garage door opener lights off, press and hold the light button for 10 seconds, until 23 the light goes on, then off again. To restore this feature, start with the garage door opener lights on, then press and hold the light button for 10 seconds until the light goes off, then on again. TIMER-TO-CLOSE (TTC) The TTC feature automatically closes the door after a specified time period that can be adjusted using a TTC enabled door control. Prior to and during the door closing the garage door opener lights will fl ash and the garage door opener will beep. BATTERY BACKUP* The battery backup system allows access in and out of your garage, even when the power is out. When the garage door opener is operating on battery power, the garage door opener will run slower, the light will not function, the Battery Status LED will glow solid orange, and a beep will sound approximately every 2 seconds. * If applicable.
Page 1 and 2: Raynor Garage Doors 1101 E. River R
Page 3 and 4: Introduction Planning Survey your g
Page 5 and 6: Introduction Carton Inventory Acces
Page 7 and 8: Assembly 2 Attach Mounting Bracket
Page 9 and 10: Installation 2 Attach the Emergency
Page 11 and 12: Installation 5 Install the Door Con
Page 13 and 14: Installation 7 Install the Protecto
Page 15 and 16: Installation MOUNTING THE SAFETY RE
Page 17 and 18: Installation ENSURE THE SAFETY REVE
Page 19 and 20: Adjustment 1 Program the Travel Lim
Page 21: Adjustment 3 Test the Safety Revers
Page 25 and 26: Operation Using the Remote Control
Page 27 and 28: Programming Internet Gateway (Not P
Page 29 and 30: Maintenance Care of Your Garage Doo
Page 31 and 32: Troubleshooting Troubleshooting The
Page 33 and 34: Repair Parts Installation Parts 4 6
Page 35 and 36: Accessories MAX ACCESSORIES Compati

Download Prodigy Instruction Manual PDF file - Raynor Garage Doors

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?