42ZV650U 47ZV650U 55ZV650U Integrated High Definition LCD ...

Recommendations

Info

Using the remote control to operate your other devices Your TV remote control has one dedicated TV mode and three programmable multi-brand modes: CABLE/SAT, DVD, and VCR/PVR. The default device modes and programmable device modes are listed below. Note: The TV remote control is preprogrammed to operate most Toshiba devices. To operate a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other devices” (at right). MODE SELECT Default device mode control (before programming) TV Toshiba TV CABLE/SAT Toshiba Satellite receiver DVD Orion DVD VCR/PVR Toshiba VCR MODE SELECT Device mode control after programming TV Toshiba TV CABLE/SAT DVD Multi-brand video/audio devices VCR/PVR Note: Although your new TV’s remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV’s remote control to operate your device or some of the features on that device, use the device’s remote control or the controls on the device. 24 Chapter 3: Using the remote control Programming the remote control to operate your other devices Device code setup 1 Find the code for your device brand in the remote control device code table on pages 26–33. If more than one code is listed, try each one separately until you find one that works. 2 Press the applicable mode select button (CABLE/ SAT, DVD, or VCR/PVR), until the mode select button blinks 3 times. 3 While holding down E, press the five-digit device code for your device. •If a valid code is entered, the mode select button will blink twice. •If an invalid code is entered, the mode select button will blink one long blink. 4 Point the remote control at the device and press p to test the code. •If the device responds to the remote control, you have entered the correct code. •If the device does not respond to the remote control, repeat steps 3 and 4 using another code. Note: After programming the remote control, make sure all necessary keys on the TV remote control (in addition to p) operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control. 5 To control the TV, press TV. Note: •Every time you change the batteries you will need to reprogram the remote control. •Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.
Searching and sampling the code of a device (8500) If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device. The keys available to be sampled, provided they are applicable to that mode, are p, 1, z,
Page 1 and 2: Integrated High Definition LCD Tele
Page 3 and 4: Important Safety Instructions 1) Re
Page 5 and 6: Service 41) WARNING: RISK OF ELECTR
Page 7 and 8: Contents Important Safety Instructi
Page 9 and 10: Features of your new TV The followi
Page 11 and 12: TV back panel connections For an ex
Page 13 and 14: Chapter 2: Connecting your TV Conne
Page 15 and 16: Connecting a device to the IR OUT i
Page 17 and 18: REGZA-LINK ® connection You can co
Page 19 and 20: Connecting a personal computer (PC)
Page 21 and 22: Learning about the remote control T
Page 23: REMOTE CONTROL KEY CH RTN/ DVD RTN
Page 27 and 28: Proscan 10392, 10566 RadioShack 105
Page 29 and 30: VCRs Brand Code A-Mark 30037, 30240
Page 31 and 32: Sony 30035, 30047, 30032, 30033, 30
Page 33 and 34: Integra 40135, 40842, 41298, 41320
Page 35 and 36: Navigating the menu system You can
Page 37 and 38: Configuring the antenna input sourc
Page 39 and 40: Setting the Auto Input feature This
Page 41 and 42: Chapter 6: Using the TV’s feature
Page 43 and 44: Elements of the Channel Browser 1 2
Page 45 and 46: Switching between two channels usin
Page 47 and 48: Picture Size Native (for 480i (HDMI
Page 49: Adjusting the picture Selecting the
Page 52 and 53: Adjusting the audio Muting the soun
Page 54 and 55: Blocking TV programs and movies by
Page 56 and 57: Locking channels With the Lock feat
Page 58 and 59: Setting the On Timer You can set th
Page 60 and 61: Amplifier VOLUME and MUTE controls
Page 62 and 63: Displaying TV status information To
Page 64 and 65: Using Expert Mode This feature indi
Page 66 and 67: Selecting the color temperature To
Page 68 and 69: Playing DivX ® files (only for USB
Page 70 and 71: To set the repeat mode: 1 Press C.
Page 72 and 73: •If you are unable to tune digita
Page 74 and 75:
Specifications Note: • This model
Page 76 and 77:
HDMI signal formats 76 Chapter 9: A
Page 78 and 79:
Limited Canadian Warranty for Toshi
Page 80 and 81:
A copy of the GPL source code in th
Page 82:
Corporate Headquarters: 82 TOTOWA R
show all

42ZV650U 47ZV650U 55ZV650U Integrated High Definition LCD ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?