IP network for 2 Wire System

More documents

Recommendations

Info

3. IP Adress Setup by IP Device SoftwareAn IP setup tool has been inserted in IP Device software. The function is the same toIP8210 config software.Steps for IP Setupa) Install PC Station package software. And IP Device software shortcut will be createdautomatically in the desktop.b) Set PC Station IPAssume using the following IP address :IP address: 192.168.0.246Subnet mask: 255.255.255.0Default gateway: 192.168.0.1Note that IP address range of PC station must be from 192.168.X.241 to 192.168.X.246. Xis the specific segment number that is configured by IP Device. Assume that 0 segmenthas been specified.c) Connect the device to PC directly or the networkThe following is a diagram of network connection2 wire riser 2 wire riser 2 wire riser2 2 2IPC IPC IPC2 wire IPinterface(IPC)2 wire IPinterface(IPC)2 wire IPinterface(IPC)IP backboneIP backbone installedusing a dedicated LANnetworkSOS-33-Guard UnitPCIP-2 wire system technical guide
d) Start IP Device softwaree) Click right mouse button on Benchmark Project, then select IP Node Config in thepop-up menuf) In IP Node Config page, press Scan & Check buttonIP-2 wire system technical guide-34-
Page 1 and 2: IP network for 2 Wire SystemUser’
Page 3 and 4: § 1.1 IP System Description2-Wire
Page 5 and 6: IP Gateway Converter: DPA-D2-IPCIP
Page 7: § 1.4 IP System Typical Applicatio
Page 10 and 11: -9-1 2 3 4 5 6DBC-41.5.2 Connect Co
Page 12 and 13: 1.5.4 Connect Quad switched 4 Camer
Page 14 and 15: HITALKMENUMONITORTALKMENUMONITORCod
Page 16 and 17: 1.5.7 Optical Fiber connection for
Page 18 and 19: § 2.1 IP‐IPG Description2.1.1 Ab
Page 20 and 21: .Intercom:The Guard Station can mak
Page 22 and 23: e.Shortup:This section offers more
Page 24 and 25: Terminal description:Item Name Desc
Page 26 and 27: 2.2.5 Wiring Diagram-25-IP-2 wire s
Page 28 and 29: 2.2.6 IP Address SetupFor construct
Page 30 and 31: * Press Properties button in theLoc
Page 32 and 33: d. Press Search… button to search
Page 36 and 37: g) Then it will pop up a window to
Page 38 and 39: 4. Find Specific Network Device in
Page 40 and 41: 5. Check Network Device OnlineThe s
Page 42 and 43: § 3.1 Software Installation1. Doub
Page 44 and 45: 6. Then click Finish button to conf
Page 46 and 47: § 3.2. IP‐Device IntroductionIP-
Page 48 and 49: 2.IP Node ConfigClick the right mou
Page 50 and 51: If you want to check if the devices
Page 52 and 53: Monitor Config: Click the right mou
Page 54 and 55: DS and Monitors Config of other blo
Page 56 and 57: 5. Call Table For BlocksFor IPC of
Page 58 and 59: If you want to cancel the mapping b
Page 60 and 61: Note that: for the above example, p
Page 62 and 63: 6. Call Table for Digital Input Com
Page 64 and 65: Press View & Edit of Button Call Ta
Page 66 and 67: Fulfill the call table, then press
Page 68 and 69: highest one.GL Call IM: To set Prio
Page 70 and 71: § 3.3. IP‐Agent Introduction3.3.
Page 72 and 73: LoginTo Access IP-Agent, you must l
Page 74 and 75: Name and Fuction of each Item in Mo
Page 76 and 77: Item Name Description1 Capture Capt
Page 78 and 79: Call Failure: *Detail refers to tro
Page 80 and 81: All the monitors of one selected bu
Page 82 and 83: d. CameraYou can connect one camera
Page 84 and 85:
Name and Function of each Item in t
Page 86 and 87:
3.3.5 Capture ViewerName and Functi
Page 88 and 89:
3.3.6 SettingFrom the top right cor
Page 90 and 91:
Channel On Start : To set initial a
Page 92 and 93:
Appendix 1Prepare a IP network in D
Page 94 and 95:
-92- IP-2 wire system technical gui
Page 96 and 97:
A Block(192.168.0.21)General Descri
Page 98 and 99:
DS Description:1) 1 DPC-D211/8 + DP
Page 100 and 101:
Appendix 2System Design Process1. A
Page 102 and 103:
System WiresSeries Name Model Qty U
show all

IP network for 2 Wire System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?