Sigma Spectrum Infusion Pump User Manual

More documents

Recommendations

Info

step in the program. Any parameter data missing within the program shall beidentified in a popup message when a program attempts to be started.- The setup data for any programmed step may be viewed by moving the highlight(using the up ARROW soft key) to the step indicator bar located at the top of thesetup screen and then using the left and right ARROW soft keys to move from step tostep.• Note that a one-second delay exists from the time a step is selected and when itssetup data is displayed. This delay is to allow rapid scrolling along the step barwithout updating the screen contents repeatedly and unnecessarily.• If the pump is stopped, any setup data may be changed by navigating to thatstep and pressing OK to move to the values that must be changed. It the pumpis running, any programmed step may be viewed by pressing the REVIEW softkey but no values may be changed with the exception of the Volume Given valuewhich may be cleared by pressing the CLEAR soft key.- Push RUN to start the program.• RUN screens appear as described in the mL/hr or Dose Error Preventionprogramming sections with the addition of a program step indicator shown in the“Step x of y” format, where x is the current step being delivered and y is the totalnumber of programmed steps.• When the program completes and the STOP key is pressed, the programschedule automatically resets (Note: Always verify current program parametersfor each step prior to starting a new infusion) itself and may be restarted withoutentering/reentering any setup data. The program will be retained indefinitelyduring power off cycles until reset. To reset the program push the RESET softkey from the PROGRAM STOPPED screen.- To clear the entire program, press the CLR ALL soft key and answer YES to theconfirmation screen.- To clear the setup data from any individual step, the pump must be stopped. Movethe highlight to the desired step in the step bar and press the CLR STEP soft key.Note that clearing a step does not delete that step unless it is the last step in theprogram.Titrating- To titrate flow rates without stopping the pump (not available in Program Modes):• Push TITRATE.• Observing the displayed hard and soft rate limits, enter a new flow rate.• Push either RUN or OK.Patency Checks- To confirm the IV line is not blocked:• Push STOP.• Open the door.• Slowly open the slide (or roller) clamp to check for gravity flow. If gravity flow cannot be achieved, a clamp is closed, the tubing is kinked, the catheter is blockedor a filter may be clogged.Keypad Lock Operation- To lock the keypad the caregiver should enter the code 429 (“K”, “E”, “Y”). This codeis entered when the pump is in the run mode to prevent unauthorized activation of- 18 -
specific key entries. A popup message shall be displayed briefly indicating thekeypad has been locked. The Key lock icon is shown on the top left corner of thescreen.- The REVIEW soft key may be pressed to allow review of the infusion setup data. Novalues may be changed and therefore navigation from value to value is not allowedwhen the keypad is locked.- The keypad will allow certain alarm conditions to be silenced and cleared while in theKeypad Lock mode.- The code must be re-entered to unlock the Keypad. If the keypad is unlocked whilereviewing the setup data and the pump is running, as long as the pump is notstopped the keypad will automatically relock upon return to the RUN screen.CAUTION: Always guard the keypad lock code from unauthorized view or access. Uncontrolledaccess by a patient or family member may possibly cause injury to the patient.Pump Standby (Hold Mode)- The pump may be placed in a standby state to prevent the occurrence of theInactivity Alarm (see ALARMS) for the period of time specified in the User Settings /Alarm Settings menu option. The default setting is to provide an infinite period oftime however this value may be changed from one minute up to 99 hours and 59minutes.- For Standby Mode to be available the set must be loaded and the infusion setupmust be complete.- Once setup has been completed and the highlight is on the Volume Given mL value,a display will appear stating that the pump may either be started or it may be placedin standby mode. To place the pump in standby, press the HOLD soft key.- When standby is activated, the indicated message will bedisplayed in a flashing format. Note that if the delay periodis set to infinite, the time value in the display will bereplaced with a dashed line.IN STANDBY01:00 (hr:min)Push RUNto start pump- While in standby, the user may press RUN at any time to begin the infusion.Pressing any other key or opening the pump door will cancel standby mode.- Pump Standby may also be used when the pump is stopped in a non-alarmcondition. Press the REVIEW soft key and then press the HOLD soft key from theSETUP screen.Delayed Start- The start of any programmed infusion may be delayed by up to 12 hours. Duringinfusion setup, move the highlight to the Volume Given mL value at the bottom of thelist - the D. RUN soft key shall appear, replacing the DOWN ARROW soft key.- Pressing the D. RUN soft key shall cause the Delay time value parameter line toappear on the setup screen. Enter any value between one minute and twelve hours(00:01 – 12:00, hr:min) and press OK.• Note: leaving the Delay time value clear and pressing OK or navigatingaway from it via an ARROW soft key will cause the parameter line to beremoved from the display for the duration of the currently programmed- 19 -
Page 1 and 2: Revision Date: 5/15//08SIGMA P/N 41
Page 3 and 4: Storing ...........................
Page 5 and 6: KEY OPERATING TIPS1. FOLLOW ALL PRO
Page 7 and 8: SYMBOLS!Attention, consult ACCOMPAN
Page 9 and 10: Front View - Pump Running with Stan
Page 11 and 12: Back View- With Standard Battery- 1
Page 13 and 14: SETUP AND OPERATIONKeys- SOFT KEYS
Page 15 and 16: - OPEN THE SLIDE AND ROLLER CLAMP.-
Page 17: • If drops are seen, the primary
Page 21 and 22: ALARMSAir-in-Line- Push OK and then
Page 23 and 24: TIPSPrevent Nuisance AlarmsThe foll
Page 25 and 26: WARNING Follow Epidural Precautions
Page 27 and 28: CAUTIONCAUTIONbore catheters or nee
Page 29 and 30: original shipping container.- Stora
Page 32 and 33: Single-PoleCat No. 55096- Adjustabl
Page 34 and 35: 11411-78 LS MIcrodrip Primary Piggy
Page 36 and 37: Compatible Baxter IV Sets - WARNING
Page 38 and 39: SIGMA SPECTRUM BATTERY PACK LIMITED
Page 40 and 41: APPENDIX A - SPECIFICATIONSPump Opt
Page 42 and 43: • Operating temperature: 60 to 80
Page 44 and 45: FLOW RATE ACCURACYEffect of Fluid C
Page 46 and 47: Flow rate Graph, Last HourSet Rate
Page 48 and 49: Trumpet Curve, 2nd HourSet Rate .5
Page 50 and 51: BOLUS ACCURACYThe SIGMA Spectrum IV
Page 52 and 53: Immunity - ESD, transient/burst, vo
Page 54 and 55: Immunity - Separation DistancesReco
Page 56 and 57: Appendix B - Low / Very Low Battery
Page 58 and 59: - 58 -
Page 60 and 61: Appendix C - Power IconsThese icons
Page 62 and 63: If the pump is runningThe image may

Sigma Spectrum Infusion Pump User Manual

Create successful ePaper yourself

Delete template?

Save as template?