SonicWALL Global VPN Client

More documents

Recommendations

Info

Enabling a VPN ConnectionEnabling a VPN connection with the SonicWALL Global VPN Client is a transparent two phaseprocess. Phase 1 enables the connection, which completes the ISAKMP (Internet SecurityAssociation and Key Management Protocol) negotiation. Phase 2 is IKE (Internet KeyExchange) negotiation, which establishes the VPN connection for sending and receiving data.When you enable a VPN connection policy, Enabled appears in the Status column of theSonicWALL Global VPN Client window. When phase 1 completes, Connected appears in theStatus column. After phase 2 is completed, a green checkmark is displayed on the VPNconnection policy icon. If an error occurs during the VPN connection, Error appears in theStatus column.Note! If the Global VPN Client doesn’t establish the VPN connection, you can use the LogViewer to view the error messages to troubleshoot the problem. See “Log Viewer” on page 39for more information.To establish a VPN connection using a VPN connection policy you created in the Global VPNClient, follow these instructions.1. Enable a VPN connection policy using one of the following methods:• If you selected Enable this connection when the program is launched in the New ConnectionWizard, the VPN connection is automatically established when you launch theSonicWALL Global VPN Client.• If your VPN connection isn’t automatically established when you launch the Global VPNClient, choose one of the following methods to enable a VPN connection:Double-click the VPN connection policy.Right-click the VPN connection policy icon and select Enable from the menu.Select the VPN connection policy and press Ctrl+B.Select the VPN connection policy, and click the Enable button on the toolbarSelect the VPN connection policy, and then choose File>Enable.• If the Global VPN Client icon is displayed in the system tray, right-click the icon and thenselect Enable>connection policy name. The Global VPN Client enables the VPN connectionwithout opening the SonicWALL Global VPN Client window.2. Depending on how the VPN connection policy is configured, the Cannot EnableConnection, Enter Pre-Shared Secret, Enter Username and Password, andConnection Warning dialog boxes may be displayed, which are explained in the followingsections.SonicWALL Global VPN Client 2.1 Administrator’s Guide Page 21
Establishing Multiple ConnectionsYou can have more than one connection enabled at a time but it depends on the connectionpolicy parameters established at the VPN gateway. If you attempt to enable a subsequent VPNconnection with a currently enabled VPN connection policy that does not allow multiple VPNconnections, the Cannot Enable Connection message appears informing you the VPNconnection cannot be made because the currently active VPN policy does not allow multipleactive VPN connection. The currently enabled VPN connection policy must be disabled beforeenabling the new VPN connection.Page 22 SonicWALL Global VPN Client 2.1 Administrator’s Guide
Page 11: DISCLAIMER OF LIABILITY. SONICWALL'
Page 15 and 16: 7. Click Install. The Setup Wizard
Page 17 and 18: VPN Connection PoliciesThe Global V
Page 19 and 20: 3. In the Choose Scenario page, sel
Page 21 and 22: Importing a VPN Configuration FileA
Page 24 and 25: You can open the SonicWALL Global V
Page 28 and 29: Entering a Pre-Shared KeyDepending
Page 30 and 31: Disabling a VPN ConnectionDisabling
Page 32 and 33: Specifying Global VPN Client Launch
Page 34 and 35: GeneralThe General page in the Conn
Page 36 and 37: User AuthenticationThe User Authent
Page 38 and 39: Peer Information Dialog BoxThe Peer
Page 40 and 41: • Advanced Packet Transmission Se
Page 42 and 43: Managing VPN Connection PoliciesThe
Page 44 and 45: Troubleshooting SonicWALL Global VP
Page 46 and 47: Setting Up Log FilesThe Auto-Loggin
Page 48 and 49: Technical SupportSelecting Help>Tec
Page 50 and 51: .Table 1: IPSec VPN and Global VPN
Page 52 and 53: SOFTWARE LICENSE AGREEMENT FORSONIC
Page 54 and 55: SOFTWARE PRODUCT is an upgrade of a
Page 56 and 57: SonicWALL Global VPN Client Support
Page 58 and 59: Deploying the default.rcf FileThere
Page 60 and 61: Default.rcf File Tag DescriptionsTh
Page 62 and 63: 00.0.0.033 (Defines the second conn
Page 64 and 65: To verify if a silent installation
Page 66 and 67: Appendix C - Running the Global VPN
Page 68 and 69: Appendix E- Log Viewer MessagesThe
Page 70 and 71: Table 2: Log Viewer MessagesERRORER
Page 76 and 77:
Table 2: Log Viewer MessagesERRORER
Page 78 and 79:
Table 2: Log Viewer MessagesINFOINF
Page 80 and 81:
Table 2: Log Viewer MessagesINFOINF
Page 82 and 83:
Table 2: Log Viewer MessagesWARNING
Page 84 and 85:
AAdding VPN Connection Policies 11D
show all

SonicWALL Global VPN Client

Create successful ePaper yourself

Delete template?

Save as template?