OPERATOR'S MANUAL BIOPROtect II Vent to ... - Baker Company

More documents

Recommendations

Info

AC. You will need to consult the most recent certification test report on the unit to determine what thevoltage setting should be for your unit.Environmental ConditionsThe BIOPROtect II is designed to be used under the following conditions:Indoor useAltitudes up to 2000 metersTemperature range from 5° C to 40° CRelative humidity up to 80%Main supply voltage105 to 130 V AC for 120V circuits200 to 240V AC for 220V circuitsMaximum relative humidity 80 percent for temperatures up to 31°C decreasing linearly to 50 percentrelative humidity at 40°C.Transient over voltages according to Installation Category (OVERVOLTAGE CATEGORIES) II per UL61010-1, Annex J.Pollution Degree 2Symbols and TerminologyProtective Earth: Any terminal which is intended for connection to an external protectiveconductor for protection against electric shock in case of a fault.!General Caution: Refer to the instruction manual for information regarding personnel andenvironment protection.Page 5 of 54
The Uses of the BIOPROtect II.II - PREPARING THE BIOPROtect II CABINET FOR USEThe BIOPROtect II cabinet has been designed to provide a work area that protects the experiment fromthe environment (Product protection), and protects the users from the experiment (personnel protection or‘containment’). The laminar flow biological safety cabinet is designed for work with Biosafety Levels 1, 2and 3 (low to moderate risk) agents as listed in The Center for Disease Control’s “Biosafety inMicrobiological and Biomedical Laboratories”, U.S. Department of Health and Human Services, PublicHealth Service, Centers for Disease Control and National Institutes of Health, U.S. Government PrintingOffice, Washington, D.C. 20402. HHS publication number (CDC) 84-8395.Extremely high risk agents assigned to Biosafety level 4 should never be used in this cabinet except in acertified BSL4 suit room. Please consult your safety professional for a proper risk assessment.Cautions* The use of any hazardous material in the cabinet requires that it be monitored by an industrial hygienist, safetyofficer or other qualified individual.* Explosive or flammable substances should never be used in the cabinet unless a qualified safety professionalhas evaluated the risk.* If hazardous biological work is to be performed, apply the appropriate biohazard decal which is enclosed. Thisis in accord with OSHA regulations, volume 39, number 125, Part II.* If chemical, radiological or other non-microbiological hazards are present, be sure to employ appropriateprotective measures in addition to formaldehyde decontamination. Call upon a suitably trained individual tomonitor the operation.Also refer to section 2 of this manual the section entitled “Decontamination”Location Within the LaboratoryPROPER PLACEMENT WITHIN THE LABORATORY IS ESSENTIAL.The ideal location for any laminar flow biological safety cabinet is in a dead-end corner of the laboratoryaway from personnel traffic, vents, doors, windows or any other sources of disruptive air currents. Publishedresearch from The Baker Company (see Rake ASM paper, reference #34 in Appendix) and unpublished testsperformed at the National Cancer Institute show that if a draft or other disruptive air current were to exceedthe intake velocity of the cabinet, then contamination can enter the work area or escape from it.Page 6 of 54
Page 1 and 2: OPERATOR’S MANUALBIOPROtect IIVen
Page 3 and 4: Table of ContentsINTRODUCTION AND W
Page 5 and 6: BGA-BIOPROtect II-20 Canopy Exhaust
Page 7 and 8: Figure 1 Typical section with airfl
Page 9: SpecificationsDimensions:Outside: 1
Page 13 and 14: Left Side & Right Side Outlet On /
Page 15 and 16: Set-up ProcedureThis section outlin
Page 17 and 18: Reacting to SpillsCaution: An Emerg
Page 19 and 20: If the cabinet is vented to the out
Page 21 and 22: IV - ON-SITE CHECKS AND MAINTENANCE
Page 23 and 24: The Airflow Balance! Warning !This
Page 25 and 26: Calibration procedure for Modus Air
Page 27 and 28: Maintenance NotesWARNING!Before any
Page 29 and 30: V. - TROUBLE SHOOTINGHere are some
Page 31 and 32: REPLACEMENT PARTS LISTPART NAMEQTYB
Page 33 and 34: Modus Installation and Operation Ha
Page 35 and 36: Page 30 of 54
Page 47 and 48: BGA-BIOPROtect II Vent to Room Page
Page 49 and 50: BGA-BIOPROtect II Vent to Room Page
Page 51 and 52: BGA-BIOPROtect II-19 Hard Exhaust C
Page 57 and 58: Wiring Diagram-Standard BIOPROtect
Page 59: WARRANTYThe Baker Company, Inc. exp

OPERATOR'S MANUAL BIOPROtect II Vent to ... - Baker Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?