OPERATOR'S MANUAL BIOPROtect II Vent to ... - Baker Company

More documents

Recommendations

Info

Design DetailsPerformance assuranceMeticulous care in manufacturing is followed by more than 14 separate performance tests prior toshipment of your cabinet. In addition, a complete factory test report on the operation of your unit isincluded at the rear of this manual.All-metal plenumsThe work area surfaces and plenums of your BIOPROtect II have been constructed entirely of metalin order to provide strength, durability, air-tightness and resistance to deterioration. Externalconstruction is of 16-gauge cold-rolled steel, protected by a smooth white baked enamel finish.Tested HEPA filtersSupply and exhaust HEPA filters in the BIOPROtect II unit have been found to be 99.99 percenteffective on particles of 0.3 micron size. Each filter is scan-tested to assure leak-free installation.Work area lightingThe fluorescent lights are externally mounted within the light canopy to minimize heat buildup in thework area. The unit uses four common F32T8 fluorescent bulbs powered by an efficient and reliableelectronic ballast.Cable PortA 2.75” I.D. cable port is provided in each side wall to accommodate communications ports fromprocess equipment without compromising performance.Optional Height Adjustable CartThe all stainless steel cart, which is optional on the BIOPROtect II was designed to accommodateprocess equipment weighing no more than 500 Lbs. It’s work surface dimensions are 90” Wide x 34” Deep.The height of the worksurface can be adjusted by the operator from 27” to 39” by using the manual crankprovided at the front of the cart. For ideal ergonomic performance the cart should be adjusted so that thework table of the equipment is at the same level as the front intake grille of door on the front of the cabinet.The cart is provided with swivel casters, all of which are locking. To retract the cart from the work area,tip the foot operated locking devices at each front caster to a horizontal position then pull the cart out of thework area. To return the cart to the cabinet push the cart back into the work area and lock the front castersby pushing down on the foot operated locking devices. Make certain that the crank handle for the lift systemis facing the front of the cabinet and is retracted under the work table before closing the door.Page 3 of 54
SpecificationsDimensions:Outside: 116.88”W x 50.00”D x 107”H (over junction boxes)Usable work area: 102”W x 36.5”D x 75”H (under diffuser)Cart worksurface: 90”W x 34” D x (27”- 39”) H (height adjusted by operator).WeightsUnit weight: The weight of the BIOPROtect II cabinet is approximately 2315 lbs.Cart weight: The weight of the BIOPROtect II cart is approximately 500 lbs.Maximum worksurface capacity: 500 Lbs. uniform load.Point loads not to exceed 125 Lbs. eachUtilities:MechanicalFour (4) 3/8” NPT female connections provided for plumbing; all are pre-plumbed to the top of theunit using 3/8” copper tubing. No service fixtures or valves are provided. User must supply fixtures tomate with 3/8” NPT female connection on side walls (see general arrangement drawing for details).ElectricalCaution: This cabinet is powered from more that one power source. The cabinet is not electrically safe unlessall power sources are disconnected. Use proper Lock Out / Tag Out procedures.All electrical wiring should comply with the National Electrical Code and any applicable Local Electrical Codesat the site of installation.The standard BIOPROtect II has three junction boxes located on the front of the top deck. Thefollowing services need to be connected to the junction boxes.One 220Volt, 20Amp, 60 Hz, Single phase connection to power the two blowers. This circuit should bewired using 12 AWG wire and provided with a 20 Amp circuit breaker that will serve as a disconnectfor this power supply.One 120 V, 15Amp, 60 Hz, Single phase connection for control power and power to the left side wallduplex outlet. This circuit should be wired using 14 AWG wire and provided with a 15 Amp circuitbreaker that will serve as a disconnect for this power supply.One 120 V, 15Amp, 60 Hz, Single phase connection for power to the right side wall duplex outlet. Thiscircuit should be wired using 14 AWG wire and provided with a 15 Amp circuit breaker that willserve as a disconnect for this power supply.The circuit breakers for these services are to be located in close proximity to the cabinet.Otherconnections may be required for optional equipment.The BIOPROtect II incorporates solid-state ‘Stedivolt’ controllers to adjust the blower motor speed. Thisunit compensates for some variation in incoming line voltage. The usable voltage range is 105 to 240VPage 4 of 54
Page 1 and 2: OPERATOR’S MANUALBIOPROtect IIVen
Page 3 and 4: Table of ContentsINTRODUCTION AND W
Page 5 and 6: BGA-BIOPROtect II-20 Canopy Exhaust
Page 7: Figure 1 Typical section with airfl
Page 11 and 12: The Uses of the BIOPROtect II.II -
Page 13 and 14: Left Side & Right Side Outlet On /
Page 15 and 16: Set-up ProcedureThis section outlin
Page 17 and 18: Reacting to SpillsCaution: An Emerg
Page 19 and 20: If the cabinet is vented to the out
Page 21 and 22: IV - ON-SITE CHECKS AND MAINTENANCE
Page 23 and 24: The Airflow Balance! Warning !This
Page 25 and 26: Calibration procedure for Modus Air
Page 27 and 28: Maintenance NotesWARNING!Before any
Page 29 and 30: V. - TROUBLE SHOOTINGHere are some
Page 31 and 32: REPLACEMENT PARTS LISTPART NAMEQTYB
Page 33 and 34: Modus Installation and Operation Ha
Page 35 and 36: Page 30 of 54
Page 47 and 48: BGA-BIOPROtect II Vent to Room Page
Page 49 and 50: BGA-BIOPROtect II Vent to Room Page
Page 51 and 52: BGA-BIOPROtect II-19 Hard Exhaust C
Page 57 and 58: Wiring Diagram-Standard BIOPROtect
Page 59:
WARRANTYThe Baker Company, Inc. exp
show all

OPERATOR'S MANUAL BIOPROtect II Vent to ... - Baker Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?