Pool & Spa Heaters

More documents

Recommendations

Info

OUTDOOR HEATERSThese heaters are certified by Advantica for outdoorinstallation, when equipped with the approved topsdesignated for outdoor use.WARNING: The heater shall not be located in an areawhere water sprinklers, or other devices, may causewater to spray through the cabinet louvres and intothe heater. This could cause heavy internal rusting ordamage some electrical components, and this wouldvoid the warranty.105 & 155 ModelsFLUE TERMINAL (Outdoor) Stackless Top IllustrationTop VentOpeningIt is recommended that the casing is cleaned andsprayed with WD40 or similar liquid, and exposedthreads on the manifolds are lightly coated in grease,after assembly.Heater withOutdoorStackless TopHeater Vent OpeningJacket Top185, 265 & 405 ModelsFLUE TERMINAL (Outdoor) Stackless Top IllustrationFLUE CONNECTIONS AND DIMENSIONS055 ModelsFLUE TERMINAL (Outdoor) Stackless Top Illustration1. Insert tabs into keyhole (4 places).Pagoda Top(ShippedLoose withHeater)1: Remove the (8) screws which fasten jacket topto heater.2: Line up top vent opening over heater ventopening3: Lower outdoor top onto unit lining up slots inoutdoor top with screw holes in jacket top.4: Reinstall (8) screws to secure jacket top andoutdoor top to unit.Press tabto locatetab1.tif2. Snap tabs into keyholes so as not to pull out.055expl1.tiftab2.tif1008-08-01
INDOOR HEATERThe design is also certified by Advantica for indoorinstallation when fitted with the appropriate draughtdiverter and a suitable flue system to outside. Notethat the heater must be in a room separated fromliving rooms and provided with appropriate ventilationdirect to the outside.055 ModelsFLUE TERMINAL (Indoor) Draught DiverterIllustrationLocate and assemble as shown. Secure with screwssupplied in envelope inside carton.MountingScrewsDraughtDiverter185, 265 & 405 ModelsFLUE TERMINAL (Indoor) Draught DiverterIllustration1. Remove the louvred jacket top by removingfour (4) No.10 flat head screws.2. If originally installed, remove "Pagoda" topfrom the louvered jacket top.3. Place the inner stack adapter panel over theflue collector inside the heater. Make surethe flanged side of the flue opening is up.4. Turn the stack (diverter) upside down and set itdown bottom side up.5. Turn the jacket top panel (removed in step 1)down and place it through the stack.6. Attach the three (3) mounting brackets to thestack using the screws provided and the holesthat are pre-drilled in the stack.brackets are positioned with theMakeflangesurenearthethe top side of the stack (see illustrationbelow).Caution must be taken not to over tighten andstrip the screw threads.7. Turn the assembled stack and jacket top, rightside up. The jacket top will be trappedbetween the brackets and the top of the stack.Place the stack over the inner adapter panelflanged hole and lower the louvered jacket toppanel back into its original position. Reinstall thefour (4) No.10 flat head screws removed instep 1 above.055expl2.tif105 & 155 ModelsFLUE TERMINAL (Indoor) Draught DiverterIllustrationLocate and assemble as shown. Secure with screwssupplied in envelope inside carton.DraughtDiverterJacketTopMountingScrews (8)Screw HoleLocation3.25"82.5mmDraughtDiverterJacket Top Panel(Part of Heater)No.10 Screw (3)Mounting Bracket (3)Inner StackAdapter PanelFlue Collector(Part of Heater)term.tifS896011405term.tif01-10-98
Page 1 and 2: Natural Gas L.P.G. Serial No:MODEL:
Page 3 and 4: ContentsINSIDE COVER - GENERAL & PE
Page 5 and 6: FOR YOUR SAFETY READ BEFORE OPERATI
Page 7 and 8: Software Version 11 and aboveOPERAT
Page 9 and 10: Software Version 11 and aboveAFTER
Page 11 and 12: PART TWO - INSTALLATION/SERVICE INS
Page 13: CLEARANCESALL HEATERSFor clearances
Page 17 and 18: DIMENSIONS - 155 Model Only220mm(8
Page 19 and 20: GAS SUPPLY CONNECTIONSGas piping mu
Page 21 and 22: This page is intentionally left bla
Page 23 and 24: DAN MAINES055 Models OnlyINOUT185,
Page 25 and 26: WIRING DIAGRAM 055-105-155 MODELS O
Page 27 and 28: WIRING DIAGRAM 185-265-405 MODELS O
Page 29 and 30: SECTION 3 / SERVICING INSTRUCTIONSG
Page 31 and 32: 185 265 and 405 ModelsOn/OffSwitchT
Page 33 and 34: 3. To remove the manual reset high
Page 35 and 36: All ModelsDESOOTING PROCEDURECAUTIO
Page 37 and 38: PROBLEM CAUSE SOLUTIONPilot outage.
Page 39 and 40: ELECTRICAL TROUBLESHOOTING055, 105
Page 41 and 42: Software Version 11 and above185, 2
Page 43 and 44: For software version 011 and above4
Page 45 and 46: BBURNER TRAYKey Description - 055 M
Page 51 and 52: Key Description - 185, 265 & 405 Mo
Page 53: 17-05-04Station LaneIndustrial Esta

Pool & Spa Heaters

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?