Pool & Spa Heaters

More documents

Recommendations

Info

OPERATING MODELS 185, 265 and 405Quick StartCheck that the Electricity and Gas Supplies areon. Turn on the Pool Pump. Turn on the Heaterwith the switch on the Front Panel and set thedesired temperature with the Pool TemperatureKnob. In a few seconds the Heater will fire.Summary of Controls (Left to Right)ON/OFF Switch - Turns the Heater On and Offand resets the Ignition Control if locked out.Lock/Unlock Button - If it is pressed for 2seconds it locks the Set Temperature so the PoolTemperature Knob is inoperative. To unlock, pressagain for 2 seconds.With a short press the Set temperature is displayed.It will flash if the Lock is ON.Pool Temperature Display - This normally showsthe Pool Temperature but also show the SettingTemperature when the Pool Temperature ControlKnob is moved. A Setting Dot is displayed whilst itis adjusted. The Display is also used for commissioningand diagnostic purposes.(Page 34)Pool Filter Blocked - YellowOn - If the pump is running and there isinsufficient pressure, possibly due to ablocked Pool Filter. The Heater will not run.Overheat - RedOn - This indicates the Heater hasoverheated and shutdown. Use the OverheatReset (see below). If this problem persiststhis should be investigated by a ServiceEngineer.Overheat Reset (not on front panel)If the Overheat Indicator has lit the Heater willnot work until the thermostat has been reset.(See page 24 for location)Wait until the Heater is cool then remove thedoor and locate the Overheat Thermostatmounted on its bracket. Press its centre and itwill click.The Red Overheat indicator will go out andthe Heater can now run.Pool Demand LED - GreenOff - There is no Pool Heating demand, poolheating is off.On - There is Pool Heating Demand and the Poolis not up to temperature.Flashing - The Pool Heating Demand is met, thepool is up to temperature.Pool Temperature Control Knob16°C to 32°C or 41°C (60°F to 90°F or 106°F)(Maximum is changed in Setup Mode, see Page 34)Rotate clockwise to increase the PoolTemperature. The Setting Temperature is shownwhilst rotating and for 3 seconds after.To lock the required Temperature Setting seeLock/Unlock Button.418-02-04
Software Version 11 and aboveOPERATING MODELS 185, 265 and 405Quick StartSummary of Controls (Left to Right)ON/OFF Switch - Lock/Unlock Button - Pool Temperature Display - SEr (Page 34)Pool Filter Blocked - YellowOverheat - RedOverheat Reset (not on front panel)Pool Demand LED - GreenOffOnFlashingPool Temperature Control Knob(Maximum is changed in Setup Mode, see Page 34)Lock/Unlock Button
Page 1 and 2: Natural Gas L.P.G. Serial No:MODEL:
Page 3 and 4: ContentsINSIDE COVER - GENERAL & PE
Page 5: FOR YOUR SAFETY READ BEFORE OPERATI
Page 9 and 10: Software Version 11 and aboveAFTER
Page 11 and 12: PART TWO - INSTALLATION/SERVICE INS
Page 13 and 14: CLEARANCESALL HEATERSFor clearances
Page 15 and 16: INDOOR HEATERThe design is also cer
Page 17 and 18: DIMENSIONS - 155 Model Only220mm(8
Page 19 and 20: GAS SUPPLY CONNECTIONSGas piping mu
Page 21 and 22: This page is intentionally left bla
Page 23 and 24: DAN MAINES055 Models OnlyINOUT185,
Page 25 and 26: WIRING DIAGRAM 055-105-155 MODELS O
Page 27 and 28: WIRING DIAGRAM 185-265-405 MODELS O
Page 29 and 30: SECTION 3 / SERVICING INSTRUCTIONSG
Page 31 and 32: 185 265 and 405 ModelsOn/OffSwitchT
Page 33 and 34: 3. To remove the manual reset high
Page 35 and 36: All ModelsDESOOTING PROCEDURECAUTIO
Page 37 and 38: PROBLEM CAUSE SOLUTIONPilot outage.
Page 39 and 40: ELECTRICAL TROUBLESHOOTING055, 105
Page 41 and 42: Software Version 11 and above185, 2
Page 43 and 44: For software version 011 and above4
Page 45 and 46: BBURNER TRAYKey Description - 055 M
Page 51 and 52: Key Description - 185, 265 & 405 Mo
Page 53: 17-05-04Station LaneIndustrial Esta

Pool & Spa Heaters

Create successful ePaper yourself

Delete template?

Save as template?