Cessna 150 Aerobat 250 ARF - Great Hobbies

More documents

Recommendations

Info

12. Attach the main landing gear to the fuselageusing two 3mm x 8mm self-tapping screws, two 3mmwashers and a #2 Phillips screwdriver. Note that thegear angle is forward when installed. 14. Locate a 2mm x 25mm machine screw and 2mmwasher. Slide the washer on the screw, then slide thescrew through the hole in the main gear. 16. Slide the plywood spacer on the screw, thenthe wheel.13. Locate the wheels for you aircraft. There are twolarger wheel for the main gear and one smaller wheelfor the nose gear.When installing the wheel and wheel pantfor the main gear, all the components mustbe inside the wheel pant before the 2mm x25mm machine screw can be tightened. 17. Once the wheel is in position, place one of thewheel collars on the screw. The round side of thecollar will be against the wheel. Use a 1.5mm hexwrench to temporarily tighten the setscrew.Always use threadlock on metal-to-metal fastenersto prevent them from vibrating loose. 15. Slide a 2mm washer on the screw, then threada 2mm nut on the screw. Leave a gap of roughly1/8-inch (3mm) between the gear and washer(as shown) so the wheel pant can fit between thewasher and gear.12 E-flite Cessna 150 Aerobat 250 ARF Assembly Manual
18. Fit the wheel pant over the wheel and itscomponents. Make sure the wheel pant is positionedbetween the gear and the washer that was installed inStep 12. You may need to reposition the 2mm nut tofit the wheel pant into position.20. Repeat steps 14 through 19 to install theremaining main wheel and wheel pant.22. Use a wheel collar and setscrew to secure thenose wheel in position. The round side of the collarwill be against the wheel. Use a 1.5mm hex wrenchto tighten the setscrew in the wheel collar. Makesure the nose wheel can rotate freely.Always use threadlock on metal-to-metal fastenersto prevent them from vibrating loose.21. Slide the nose wheel pant on the nose gearaxle. A plywood spacer and the nose wheel arethen slid onto the nose gear axle.23. Use canopy glue to glue the nose gear wire intothe recess of the wheel pant. Use low-tack tape tohold the wheel pant in position while the glue cures.Allow the glue to fully cure before proceeding. 19. Use a #1 Phillips screwdriver to tighten themachine screw wile holding the 2mm nut usinghemostats. Make sure the landing gear is sittingin the recess of the wheel pant. Once the screwhas been tightened, use a 1.5mm hex wrench toposition the wheel collar so the wheel can rotatewithout any binding.Always use threadlock on metal-to-metal fastenersto prevent them from vibrating loose.E-flite Cessna 150 Aerobat 250 ARF Assembly Manual13
Page 1 and 2: Cessna 150 Aerobat 250 ARFAssembly
Page 3: Table of ContentsNotice............
Page 6 and 7: 4. Use a very small amount of mediu
Page 8 and 9: 15. With the aileron servo centered
Page 10 and 11: Landing Gear InstallationRequired P
Page 14: Motor and Speed Control Installatio
Page 17 and 18: 3. Slide the wing so it fits tightl
Page 19 and 20: Do not use CA accelerator when glui
Page 21 and 22: Rudder, Elevator and Nose GearLinka
Page 23 and 24: 11. While the rudder servo is cente
Page 25 and 26: Motor Battery, Cowl, Propeller andS
Page 29 and 30: Range Test Your RadioBefore each fl
Page 31 and 32: Warranty RequirementsFor Warranty c
Page 33 and 34: C. FREE FLIGHT1. Must be at least 1
Page 35 and 36: E-flite Cessna 150 Aerobat 250 ARF

Cessna 150 Aerobat 250 ARF - Great Hobbies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?