2.2 The IBM 7171 ASCII Device Attachment Control Unit - Index of

More documents

Recommendations

Info

9.22 P - Display Port ConfigurationUse the P command to display the IBM 7171 current port configuration.Format:Where:tcIndicates a request to display the port configuration of a specific Te.Example:pThis command requests a display of the IBM 7171. port configuration. A responsemight be:1/tc 0 0-036C IBM3101tc 0 4-04AA IBM3101tc 1 8-Unattachedtc 1 12-059D IBM31011-Unattached5-Unattached9-Unattached13-Unattached2-046B HARDCOPY6-Unattached10-Unattached14-Unattached3-Unattached7-Unattached11-Unattached15-UnattachedThe TC on which the ports exist is listed at the start of the line. For each portthere is the following information: dvc,addr,typedvcIs the device number of that port. This is a decimal value, and is to be usedfor all other device specific commands, such as Configure, Force, and Note.addr Indicates the segment address of this port's data control block.type Indicates what type of terminal, if known, is attached to this port.Notes:1. If the terminal is at the 'ENTER TERMINAL TYPE' message, and is not yetinitialized, this field will be left blank.2. Any port listed as UNATTACHED indicates that either nothing is plugged intothat port, or the terminal is powered off.3. If the terminal type was predefined for a specific port but the terminal type cannot be determined from the address specified, the word INVALID will be displayed.Chapter 9. Special Maintenance Facility and System Messages 9-25
4. Any invalid characters that are typed in response to the ENTER TERMINALTYPE message will be displayed in this field. This is to aid in locating certainterminals. For instance, if a unique character sequence was typed in responseto the ENTER TERMINAL TYPE message, such as "xxxxx," the "xxxxx"would show up in the Ports response, and the device number of the terminal inquestion could be identified.Error Messages:Invalid TC board specified.TC not inserted.9-26 IBM 7171 Reference Manual and Programming Guide
Page 3 and 4:
Federal Communications Commission (
Page 5 and 6:
Appendix C. IBM 7171 SupporfUtility
Page 7:
viIBM 7171 Reference Manual and Pro
Page 11 and 12:
9.28 TS - Store to Terminal Control
Page 13 and 14:
C.5 Support Utilities .............
Page 15 and 16:
xivIBM 7171 Reference Manual and Pr
Page 17 and 18:
8-1. Illustration of the Front of t
Page 19 and 20:
xviiimM 7171 Reference Manual and P
Page 21 and 22:
1.2 ASCII Device SupportThe IBM 717
Page 23 and 24:
using the ROLM3270 terminal type. F
Page 25 and 26:
On the IBM Personal Computer when r
Page 27 and 28:
2.2.2 Terminal ManagementTerminal m
Page 29 and 30:
2.3.1 ASCII TerminalsASCII Display
Page 31 and 32:
ATTRIBUTESPROTECTEDNUMERICINTENSITY
Page 33 and 34:
uffer indicates it is displayed, an
Page 35 and 36:
In addition, the following display
Page 37 and 38:
2.7.2 Preparing the MVS SystemAn ex
Page 39 and 40:
2-16 IBM 7171 Reference Manual and
Page 41 and 42:
- the "backslash" (\) is used for t
Page 43 and 44:
• APL Mode off• ASCII Input in
Page 45 and 46:
Trailing nulls on the line are stil
Page 47 and 48:
3277 Insert ModeAPL Character Set -
Page 49 and 50:
Return to 'ENTER TERMINAL TYPE:' Me
Page 51 and 52:
3.2.2 Trying to Change Protected Da
Page 53 and 54:
3.2.8 Other ErrorsFor more informat
Page 55 and 56:
DMlS20 For the Datamedia 1520DMlS21
Page 57 and 58:
4.3 Terminal Definition Table Infor
Page 59 and 60:
Move Cursor LeftThe Cursor Left com
Page 61 and 62:
ClearWhen the IBM 7171 receives the
Page 63 and 64:
Keyboard Assignment ConsiderationsX
Page 65 and 66:
These output strings are called Con
Page 67 and 68:
s DCOO:2FA 2004s DCOO:400 s DCOO:42
Page 69 and 70:
Graphic Rendition StringsSGR stands
Page 71 and 72:
The function of the host translate
Page 73 and 74:
Data Area 2This data area contains
Page 75 and 76:
2-3 Baud Rate. If the baud rate is
Page 77 and 78:
4.4.3 Data Area 2 LayoutFollowing i
Page 79 and 80:
Address02F402F602FA02FEDefinition o
Page 81 and 82:
Terminal Hetlder Information: The f
Page 83 and 84:
The address of the standard list is
Page 85 and 86:
Each string starts at the address g
Page 87 and 88:
diately, using the same input chara
Page 89 and 90:
Most of the other IBM 3101 control
Page 91 and 92:
Index: The target field of the INDE
Page 93 and 94:
4.5.2 Function Name TableThe follow
Page 95 and 96:
MUL TRUBOUTPGUPPGDNallows an input
Page 97 and 98:
4.5.4 ROM Pointers to Internal Info
Page 99 and 100:
Terminal Name Record FormatThe form
Page 101 and 102:
Examples of a Terminal Names ListTh
Page 103 and 104:
Here are the Maintenance Facility c
Page 105 and 106:
DEFAULT_PHYS I CAL_COLUMNSDEFAULT_L
Page 107 and 108:
TERMINAL HEADER --Fixed length of 2
Page 109 and 110:
CSS-String lengths are variable.CUR
Page 111 and 112:
6. Enter the Control Sequence Strin
Page 113 and 114:
list of host translate table addres
Page 115 and 116:
Example 2: Here is an example of ch
Page 117 and 118:
17. Copy the IBM31 0 1 terminal hea
Page 119 and 120:
This address is contained in ROM in
Page 121 and 122:
5.1.2 World Trade Interface Standar
Page 123 and 124:
TABLE 2 INTERFACE TYPE CCITT-V.24DA
Page 125 and 126:
5.4 Baud Rates SupportedThe followi
Page 127 and 128:
5.7 Operational PhaseThe operationa
Page 129 and 130:
5.8.2 Control Signal PacingAs menti
Page 131 and 132:
5.9.3 Locally Attached (Direct Conn
Page 133 and 134:
modem. If the carrier is lost, RLSD
Page 135:
5 -16 IBM 7171 Reference Manual and
Page 139 and 140:
Command codes are shown below.Comma
Page 141 and 142:
the data has been entered. During t
Page 143 and 144:
6.2.4 Orders and AttributesOrdersOr
Page 145 and 146:
To continue the search for an unpro
Page 147 and 148:
ACTION AID Reaction to Resultant(ke
Page 149 and 150:
BYTEo234567AI DCURSOR- ADDRESSSBAAT
Page 151 and 152:
in the data stream (nulls are suppr
Page 153 and 154:
Programming Restriction: Erase All
Page 155 and 156:
Sense ID is honored when the IBM 71
Page 157 and 158:
D/SPD I RESERVEDMDTo 2 3 4 5 6EBCDI
Page 159 and 160:
Order EBCDIC ExplanationCR OD Carri
Page 161 and 162:
6.4.1 Interface Operations (IBM 717
Page 163 and 164:
Bit Name Condition2 Control Set fol
Page 165 and 166:
ErrorStatus Sense Recovery(Hex) (He
Page 167 and 168:
Asynchronous Status: Asynchronous s
Page 169 and 170:
6.4.2 Error Recovery ProceduresIBM
Page 171 and 172:
Data Pending State.• Data Pending
Page 173 and 174:
Keyboard Action orData Stream state
Page 175 and 176:
Setup Functions for Host Applicatio
Page 177 and 178:
Set Home Line, Set Left Margin, Set
Page 179 and 180:
6-44 IBM 7171 Reference Manual and
Page 181 and 182:
After the CPU diagnostic microcode
Page 183 and 184: Symptom IndexLocate symptom in the
Page 185 and 186: Terminal Type Specification ErrorsF
Page 187 and 188: F-5: No data sent to terminal.This
Page 189 and 190: IBM 7171 Physical LayoutFigure 8-1
Page 191 and 192: F-7: Screen problems appear after e
Page 193 and 194: F-10: Power Indicator does not turn
Page 195 and 196: 11. Does the Ready Indicator light?
Page 197 and 198: Failing Condition #1Card IndicatorC
Page 199 and 200: Falling Condition #5Card IndicatorC
Page 201 and 202: Failing Condition #8Card IndicatorC
Page 203 and 204: 18. Return 7171 to normal operation
Page 205 and 206: 8. If problem is resolved return 71
Page 207 and 208: This devices' address may not be en
Page 209 and 210: 8-28 IBM 7171 Reference Manual and
Page 211 and 212: Now key in the terminal type being
Page 213 and 214: The password changing function of t
Page 215 and 216: 9.7 A - Display AC2 Data Block for
Page 217 and 218: 02-01 Number of data bits.00 = 5 da
Page 219 and 220: Error Messages:Invalid device numbe
Page 221 and 222: 9.10 CO - Copy Data BlockUse the CO
Page 223 and 224: 9.12 D - Date CommandsUse the DATE
Page 225 and 226: Date:Device #ParametersMessageIndic
Page 227 and 228: 9.15 FD/FT - Force a Device Offline
Page 229 and 230: 9.17 1- Inword CommandUse the I com
Page 231 and 232: 9.19 MW - Display One Word of CPU B
Page 233: 9.21 0 - Outword CommandUse the 0 c
Page 237 and 238: 9.24 S - Store to CPU Board MemoryU
Page 239 and 240: 9.25 SW - Store One Word into CPU B
Page 241 and 242: Cursor BaseHost Trans TablesTerm Tr
Page 243 and 244: 9.28 TS - Store to Terminal Control
Page 245 and 246: 9.30 - - Invoke Calculator Function
Page 247 and 248: 9.31 System Error MessagesFollowing
Page 249 and 250: Multiple DMA requests were made to
Page 251 and 252: 9-42 mM 7171 Reference Manual and P
Page 253 and 254: A.2 Host Tables for 3277 Device Typ
Page 255 and 256: A.2.3 3277 Basic Translate Table fo
Page 257 and 258: A.3 Host Tables for 3278 Device Typ
Page 259 and 260: A.3.3 3278 APL Table for Write Data
Page 261 and 262: A.3.S 3278 Attribute Byte Table for
Page 263 and 264: A.4 Terminal Translate TablesThese
Page 265 and 266: A.4.3 Typewriter Paired APL Output
Page 267 and 268: A.4.S Bit Paired APL Output Transla
Page 269 and 270: A -18mM 7171 Reference Manual and P
Page 271 and 272: B.2 Table DescriptionThe key settin
Page 273 and 274: 00 NULL 18 CAN01 SOH 19 EM02 STX 1A
Page 275 and 276: B.6.2 Program Function KeysFUNCTION
Page 277 and 278: B.6.4 Local Reset and Control Funct
Page 279 and 280: B.7.2 Program Function KeysFUNCTION
Page 281 and 282: B. 7.4 Local Reset and Control Func
Page 283 and 284: 10. Wait a few seconds. When the co
Page 285 and 286:
B.8.2 Program Function KeysFUNCTION
Page 287 and 288:
B.8.5 Installation HintsThere are t
Page 289 and 290:
B.9.2 Program Function KeysFUNCTION
Page 291 and 292:
B.9.4 Local Reset and Control Funct
Page 293 and 294:
B.I0 ADM-31 TerminalB.l0.l Control
Page 295 and 296:
FUNCTION ASC I I-CODE ADM-31 KEY(-S
Page 297 and 298:
B.lO.4 Local Reset and Control Func
Page 299 and 300:
B.ll.2 Program Function KeysFUNCTIO
Page 301 and 302:
B.11.4 Local Reset and Control Func
Page 303 and 304:
B.12.2 Program Function KeysFUNCTIO
Page 305 and 306:
FUNCTION ASC I I-CODE VT-100 KEY(-S
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
B.14.3 Setup FunctionsThe setup fun
Page 317 and 318:
I B.15 IBM 316X TerminalB.IS.I Cont
Page 319 and 320:
Page 321 and 322:
• AUTOLF=OFF• SEND=PAGE• SEND
Page 323 and 324:
I B.16 ROLM 3270 TerminalI B.16.1 C
Page 325 and 326:
Function Corresponding ASCI I Corre
Page 327 and 328:
Page 329 and 330:
B.17 TYPETERM Typewriter TerminalTY
Page 331 and 332:
B-62 IBM 7171 Reference Manual and
Page 333 and 334:
• 7171TML.COM, which provides:Exp
Page 335 and 336:
When using 7171 TML. COM, it is pos
Page 337 and 338:
C.7.2 .CTL files.CTL files contain
Page 339 and 340:
Here is an abbreviated example:ORG=
Page 341 and 342:
C.S.3 Ports ConfigurationPORTS, 717
Page 343 and 344:
7171TMLMAIN (7171TML)IMPRTIEDIT.TML
Page 345 and 346:
C.11 IBM 7171 Support Utility Opera
Page 347 and 348:
to this rule is ROM terminal defini
Page 349 and 350:
e.15 IBM 7171 Support Utility from
Page 351 and 352:
C.16 Main MenuFigure C-7 illustrate
Page 353 and 354:
C.16.1 Ports MenuFigure C-8 illustr
Page 355 and 356:
Ports LoadFigure C-9 illustrates th
Page 357 and 358:
10 Parity. 0 = Odd or Mark Parity,
Page 359 and 360:
Ports SaveFigure C-11 illustrates t
Page 361 and 362:
IBM 7171 Support Utility (C) Copyri
Page 363 and 364:
RETURNReturn to the main menu.C-32
Page 365 and 366:
Terminal EditFigure C-16 illustrate
Page 367 and 368:
Terminal Features: Figure C-17 illu
Page 369 and 370:
Output Sequence: Figure C-19 illust
Page 371 and 372:
Login Sequence: Figure C-20 illustr
Page 373 and 374:
Graphics Strings Figure C-22 illust
Page 375 and 376:
Save. TRM File- TERMS - SAVE .TRMSA
Page 377 and 378:
Terms ReportFigure C-26 illustrates
Page 379 and 380:
IBM 7171 Support utility (c) Copyri
Page 381 and 382:
C.16.3 Edit .CTL MenuFigure C-28 il
Page 383 and 384:
Load .CTLFigure C-29 illustrates th
Page 385 and 386:
Save .CTL FlleFigure C-31 illustrat
Page 387 and 388:
4. A copy of the VALID TYPES ARE me
Page 389 and 390:
Note: Do not make the ZAP password
Page 391 and 392:
717110 LOGON Errors: Failure at STA
Page 393 and 394:
Once the Connected message appears,
Page 395 and 396:
ASYNC FRAME ERROR ***717110 This er
Page 397 and 398:
NO ASYNC DATA FOR 5 SECS717110 (abe
Page 399 and 400:
Infonnational~essagesThese messages
Page 401 and 402:
Logoff completedDialup: Okay to han
Page 403 and 404:
Warning MessagesCROSS-CHECK: FEAT (
Page 405 and 406:
7171LINK ABEND: CONTROL FILE SCAN E
Page 407 and 408:
INVALID BAUD RATE7171 TERM This err
Page 409 and 410:
• The optional 2 can be used to s
Page 411 and 412:
• COMMENT LINES begin with a STAR
Page 413 and 414:
C.19.2 7171MPRT PORT MacroPORTportn
Page 415 and 416:
C.19.4 7171MLNK TERM Macro[label] T
Page 417 and 418:
C.19.S 7171MLNK CSS Macro[ label] C
Page 419 and 420:
Series/17171 Support utilitiesComme
Page 421 and 422:
• Outputtab labels should be the
Page 423 and 424:
C.24 EDL to TML ConversionConversio
Page 425 and 426:
Change DOT to PERIOD.Note: See Figu
Page 427 and 428:
NODE01NODE02**EQU *NODE J,GOTO,NODE
Page 429 and 430:
e.2S.l Function Name TableThe follo
Page 431 and 432:
213 = Invalid label reference214 =
Page 433 and 434:
DOS Batch File ExampleECHOECHOECHOE
Page 435 and 436:
D.3 Definition of the IBM 7171/User
Page 437 and 438:
4. Dumpa. InputTo issue a dump, ent
Page 439 and 440:
And a response might be::1234: 1234
Page 441 and 442:
TYPPFKTYPPAKFUNCPFKFUNBPFKFUNCXFUNC
Page 443 and 444:
*ABCDEF 173MNO 174QWERT 175NECVDI 1
Page 445 and 446:
ALTERNATE KEYBOARD*****************
Page 447 and 448:
*FUNCPFK***FUNBPFK*****************
Page 449 and 450:
***********************************
Page 451 and 452:
***********************************
Page 453 and 454:
***********************************
Page 455 and 456:
*****D3ESC*D3ESC2*D3SETD3SET2DM3PFK
Page 457 and 458:
*VTEE*VTEEO*VTEO*VTEOP*************
Page 459 and 460:
***********************************
Page 461 and 462:
***********************************
Page 463 and 464:
***********************************
Page 465 and 466:
***********************************
Page 467 and 468:
** ********************************
Page 469 and 470:
***********************************
Page 471 and 472:
***********************************
Page 473 and 474:
*NODE01*NODE02*********************
Page 475 and 476:
***********************************
Page 477 and 478:
*N316X9*NODE34****NODE35*NODE36*NOD
Page 479 and 480:
E-40 IBM 7171 Reference Manual and
Page 481 and 482:
customizationchanging communication
Page 483 and 484:
local editing functions 2-4local re
Page 485 and 486:
DPC= C-85DPR= C-85FLAGS= C-85HTRAN=
Page 487 and 488:
International BusinessMachines Corp
Page 489:
GA37 -0021 -0Reader's Comment FormC
show all

2.2 The IBM 7171 ASCII Device Attachment Control Unit - Index of

Create successful ePaper yourself

Delete template?

Save as template?