General Products - ALP Industries Inc.

More documents

Recommendations

Info

107 SECTION 7 - FittingsLarge Bolt Type Anchor ShackleNOTICE: All 2140 shackles 200 Tonsand larger are magnetic particleinspected. Certification available uponrequest.• Shackles are Quenched and Tempered and can meet DNVimpact requirements of 42 joules at -20 o C.• Working Load Limit is permanently shown on everyshackle• Alloy bows, Alloy bolts• Quenched and Tempered• All sizes are individually proof tested to 2.0 time the WorkingLoad Limit• Shackles 200 metric tons and larger are provided as follows:• Non Destructive tested• Serialized pin and bow• Material Certification (Chemical)• Certification must be requested at time of order• Forged Alloy steel 30 thru 175 metric tons. Cast AlloySteel 200 thru 400 metric tons.• Pins are galvanized and painted red• G-2140 meets the requirements of Federal SpecificationRR-C-271D, Type IVA, Grade B, Class 3, except for thoseprovisions required of the contractor.G-2140/S-2140 Shackle SpecificationsNominalShackleSize (in.)WorkingLoadLimit (t)*G-2140Galv.Stock No.S-2140S.C.WeightEach (lbs.)1-1/2 30 1021110011 1021129 18.81-3/4 40 1021138 1021147 33.92 55 1021156 1021165 52.02-1/2 85 1021174 1021183 96.03 120 1021192 -- 178.03-1/2 ^150 1021218 -- 265.04 ^175 1021236 -- 338.04-3/4** ^200 1021414 -- 450.05** ^250 1021432 -- 600.06** ^300 1021450 -- 775.07** ^400 1021478 -- 1102.0NominalShackleSize (in.)WorkingLoadLimit* (t)Dimensions (in.) Tolerance +/-A B C D E F G H J K L A E1-1/2 30 2.38 3.62 1.62 1.63 5.75 1.39 6.88 7.73 10.00 3.88 1.53 .13 .251-3/4 40 2.88 4.19 2.25 2.00 7.00 1.75 8.81 9.33 12.34 5.00 1.84 .13 .252 55 3.25 4.81 2.40 2.25 7.75 2.00 10.16 10.41 13.68 5.75 2.08 .13 .252-1/2 85 4.12 5.81 3.12 2.75 10.50 2.62 12.75 13.58 17.90 7.25 2.71 .25 .253 120 5.00 6.50 3.63 3.25 13.00 3.00 14.62 15.13 21.50 7.88 3.12 .25 .253-1/2 ^150 5.25 8.00 4.38 3.75 14.63 3.75 17.02 17.62 24.88 9.00 3.62 .25 .254 ^175 5.50 9.00 4.56 4.25 14.50 4.00 18.00 20.37 25.68 10.00 4.00 .25 .254-3/4** ^200 7.25 10.50 6.00 4.75 15.63 3.75 21.00 21.21 29.25 11.00 4.50 .25 .255** ^250 8.50 12.00 6.50 5.00 20.00 3.88 24.50 22.68 35.00 13.00 4.50 .25 .256** ^300 8.38 12.00 6.75 6.00 19.50 4.75 25.00 25.06 35.25 13.00 5.00 .25 .257** ^400 8.25 14.00 7.25 7.00 22.50 6.50 26.00 28.68 40.25 13.00 6.00 .25 .25* Note: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Load is 4 times the Working Load Limit on 200 thru 400 Metric Tons.For sizes 30 thru 175 Metric Tons, Minimum Ultimate Load is 5.4 times the Working Load Limit.** Cast Alloy Steel.^ Furnished with Round Head Bolts with welded handle.FOR MORE INFORMATION CONTACT OUR NEAREST BRANCH OFFICE
SECTION 7 - Fittings 108Hoist HooksHoist HooksWarnings and Application InstructionsS-3319 S-319 S-320 S-322 S-3322BSeries Series SeriesPositioning OnlyImportant Safety Information - Read and Follow• A visual periodic inspection for cracks, nicks, wear, gouges and deformationas part of a comprehensive documented inspection program,should be conducted by trained personnel in compliance with theschedule in ANSI B30. 10.• For hooks used in frequent load cycles or pulsating loads, the hookand threads should be periodically inspected by Magnetic Particle orDye Penetrant. (Note: Some disassembly may be required).• Never use a hook whose throat opening has been increased, or whosetip has been bent more than 10 degrees out of plane from the hookbody, or is in any other way distorted or bent. Note: A latch will notwork properly on a hook with a bent or worn tip.• Never use a hook that is worn beyond the limits shown in Figure 1.• Remove from service any hook with a crack, nick, or gouge. Hookswith a crack, nick, or gouge shall be repaired by grinding lengthwise,following the contour of the hook, provided that the reduced dimensionis within the limits shown in Figure 1.• Never repair, alter, rework, or reshape a hook by welding, heating,burning, or bending.• Never side load, back load, back load, or tip load a hook. (Side loading,back loading and tip loading are conditions that damage andreduce the capacity of the hook.) (See Figure 2.)• Eye hooks, shank hooks and swivel hooks are designed to be usedwith wire rope or chain. Efficiency of assembly may be reducedwhen used with synthetic material.• Do not swivel the S-322 swivel hook while it is supporting a load.The S-322 is distinguishable by hex nut and flat washers.• The S-3322 swivel hook is designed to rotate under load. The S-3322is distinguishable from the S-322 by use of a round nut designed toshield bearing.• The use of a latch may be mandatory by regulations or safety codes;e.g., OSHA, MSHA, ANSI/ASME B30, Insurance, etc. (Note: Whenusing latches, see instructions in “Understanding: The Crosby GroupWarnings” for further information.)• Always make sure the hook supports the load. (See Figure 3). Thelatch must never support the load (See Figure4).• When placing two (2) sling legs in hook, make sure the angle from thevertical to the outermost leg is not greater than 45 degrees, and theincluded angle between the legs does not exceed 90 degrees* (SeeFigure 5).• See ANSI/ASME B30.10 “Hooks” for additional informationWARNING• Loads may disengage from hook if proper procedures are notfollowed.• A falling load may cause serious injury or death.• See OSHA Rule 1926.550(g) for personnel hoisting by cranes orderricks, and OSHA Directive CPL 2-1.29-Interim InspectionProcedures During Communication Tower Construction Activities.A Crosby 319, 320, or 322 hook with a PL Latch attachedand secured with a bolt, nut and cotter pin (or toggle pin) maybe used for lifting personnel. A Crosby 319N, 320N or 322Nhook with a S-4320 Latch attached and secured with cotter pinor bolt, nut and pin; or a PL-N latch attached and secured withtoggle pin may be used for lifting personnel. A hook with aCrosby SS-4055 latch attached shall NOT be used for personnellifting.• See OSHA Directive CPL 2-1.29 - Crosby does not recommendthe placement of lanyards directly into the positive lockingCrosby hook when hoisting personnel. Crosby requires that allsuspension systems (vertical lifelines/lanyards) shall be gatheredat the positive locked load hook by use of a master link, ora bolt-type shackle secured with cotter pin• Threads may corrode and/or strip and drop the load.• Remove securement nut to inspect or to replace S-322, S-3316and S3319 bearing washers (2).• Hook must always support the load. The load must never besupported by the latch.• Never apply more force than the hook’s assigned WorkingLoad Limit (WLL) rating.• Read and understand these instructions before using hook.Figure 1Zone A: Repair Not RequiredZone B: 10% of Original DimensionZone C: 5% of Original DimensionZone D: Consult Minimum Thread Chart 2009 Crosby Catalog p. 125.Figure 2Figure 3 Figure 4 Figure 5For two legged slings with angles greater than 90 o , use an intermediatelink such as a master link or bolt type shackle to collect the legs of theslings. The intermediate link can then be placed over the hook to providean in-line load on the hook. This approach must also be usedwhen using slings with three or more legs.•RIGHT WRONG RIGHTFOR MORE INFORMATION CONTACT OUR NEAREST BRANCH OFFICE
Page 2 and 3:
Corporate HistoryIn 1981 Reitzel Sw
Page 4 and 5:
TABLE OF CONTENTSWIRE ROPEGeneral I
Page 6 and 7:
1 SECTION 1 - Wire RopeWIRE ROPEGen
Page 8 and 9:
3 SECTION 1 - Wire Ropebeen applied
Page 10 and 11:
5 SECTION 1 - Wire Ropeends will be
Page 12 and 13:
7 SECTION 1 - Wire RopeTroubleshoot
Page 14 and 15:
9 SECTION 1 - Wire RopeSuggested Wi
Page 16 and 17:
11 SECTION 1 - Wire RopeRopesWire R
Page 18 and 19:
13 SECTION 1 - Wire RopeSix Strand
Page 20 and 21:
15 SECTION 1 - Wire RopeRotation Re
Page 22 and 23:
17 SECTION 1 - Wire RopeGalvanized
Page 24 and 25:
19 SECTION 1 - Wire RopeBethlehem8-
Page 26 and 27:
21 SECTION 1 - Wire RopeBridonEndur
Page 28 and 29:
23 SECTION 1 - Wire RopeBridonEndur
Page 30 and 31:
25 SECTION 1 - Wire RopeWireco7-FLE
Page 32 and 33:
27 SECTION 1 - Wire RopeSling Capac
Page 34 and 35:
29 SECTION 1 - Wire RopeSling Capac
Page 36 and 37:
31 SECTION 1 - Wire RopeTerminal Ef
Page 38 and 39:
33 SECTION 2 - Elevator ProductsBet
Page 40 and 41:
35 SECTION 2 - Elevator ProductsBet
Page 42 and 43:
37 SECTION 2 - Elevator ProductsRee
Page 44 and 45:
39 SECTION 2 - Elevator ProductsGov
Page 46 and 47:
41 SECTION 2 - Elevator ProductsWir
Page 48 and 49:
43 SECTION 3 - ChainCHAINTypes of C
Page 50 and 51:
45 SECTION 3 - ChainWelded Single C
Page 52 and 53:
47 SECTION 3 - ChainWelded Quadrupl
Page 54 and 55:
49 SECTION 3 - ChainCrosby ELIMINAT
Page 56 and 57:
51 SECTION 3 - ChainKuplex ® II Ku
Page 58 and 59:
53 SECTION 3 - ChainCrosby ® Grade
Page 60 and 61:
55 SECTION 3 - ChainCrosby 8/10 TM
Page 62 and 63: 57 SECTION 3 - ChainA-1355 Chain Ch
Page 64 and 65: 59 SECTION 3 - ChainRecommended Cha
Page 66 and 67: 61 SECTION 3 - ChainTable of WearCh
Page 68 and 69: 63 SECTION 3 - ChainGrade 70 Transp
Page 70 and 71: 65 SECTION 3 - ChainBinders & Chain
Page 72 and 73: 67 SECTION 4 - Mesh SlingsAlloy Cha
Page 74 and 75: 69 SECTION 5 - Synthetic SlingsCons
Page 76 and 77: 71 SECTION 5 - Synthetic SlingsSaf-
Page 78 and 79: 73 SECTION 5 - Synthetic SlingsPenc
Page 80 and 81: 75 SECTION 5 - Synthetic SlingsWeb
Page 82 and 83: 77 SECTION 5 - Synthetic SlingsTypi
Page 88 and 89: 83 SECTION 5 - Synthetic SlingsBrai
Page 90 and 91: 85 SECTION 6 - Cargo ControlCARGO C
Page 92 and 93: 87 SECTION 6 - Cargo ControlSafety
Page 94 and 95: 89 SECTION 6 - Cargo ControlBuckle
Page 96 and 97: 91 SECTION 6 - Cargo ControlWinches
Page 98 and 99: 93 SECTION 6 - Cargo ControlFlat Ho
Page 100 and 101: 95 SECTION 6 - Cargo Control“E”
Page 102 and 103: 97 SECTION 7 - FittingsG-450 Crosby
Page 104 and 105: 99 SECTION 7 - FittingsG-429 Crosby
Page 106 and 107: 101 SECTION 7 - FittingsG-340 & S-3
Page 108 and 109: 103 SECTION 7 - FittingsScrew Pin S
Page 110 and 111: 105 SECTION 7 - FittingsRound Pin S
Page 114 and 115: 109 SECTION 7 - FittingsS-320 & s-3
Page 116 and 117: 111 SECTION 7 - FittingsShank HookS
Page 118 and 119: 113 SECTION 7 - FittingsSHUR-LOC ®
Page 120 and 121: 115 SECTION 7 - FittingsS-4320 HOOK
Page 122 and 123: 117 SECTION 7 - FittingsSS-4055 Saf
Page 124 and 125: 119 SECTION 7 - FittingsSpecialty H
Page 126 and 127: 121 SECTION 7 - FittingsThimblesExt
Page 128 and 129: 123 SECTION 7 - FittingsSlip-Thru T
Page 130 and 131: 125 SECTION 7 - FittingsWedge Socke
Page 132 and 133: 127 SECTION 7 - FittingsClosed Spel
Page 134 and 135: 129 SECTION 7 - FittingsCLOSED SWAG
Page 136 and 137: 131 SECTION 7 - FittingsTurnbuckles
Page 138 and 139: 133 SECTION 7 - FittingsJaw & Eye T
Page 140 and 141: 135 SECTION 7 - FittingsHook & Eye
Page 142 and 143: 137 SECTION 7 - FittingsSwivelsEqui
Page 144 and 145: 139 SECTION 7 - FittingsHoist Rings
Page 146 and 147: 141 SECTION 7 - FittingsHeavy Duty
Page 148 and 149: 143 SECTION 7 - FittingsEZ-Torque T
Page 150 and 151: 145 SECTION 7 - FittingsElectroline
Page 152 and 153: 147 SECTION 7 - FittingsTYPICAL ASS
Page 154 and 155: 149 SECTION 7 - FittingsCable SizeN
Page 156 and 157: 151 SECTION 7 - FittingsNicopress T
Page 158 and 159: 153 SECTION 7 - FittingsStainless S
Page 160 and 161: 155 SECTION 8 - BlocksBLOCKSWire Ro
Page 162 and 163:
157 SECTION 8 - BlocksDiamond & Ova
Page 164 and 165:
159 SECTION 8 - BlocksCrane Blocks#
Page 166 and 167:
161 SECTION 8 - BlocksOverhaul Ball
Page 168 and 169:
163 SECTION 8 - BlocksTackle Block
Page 170 and 171:
165 SECTION 9 - Hoists, Pullers & W
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
179 SECTION 10 - Below-the-Hook Acc
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
207 SECTION 11 -CordageNylonBlue St
Page 214 and 215:
209 SECTION 11 -CordageRope Use Ref
Page 216 and 217:
211 SECTION 12 - Fall RestraintUniv
Page 218 and 219:
213 SECTION 12 - Fall RestraintSusp
Page 220 and 221:
215 SECTION 13 - Marine ProductsMAR
Page 222 and 223:
217 SECTION 13 - Marine ProductsLig
Page 224 and 225:
219 SECTION 13 - Marine ProductsCha
Page 226 and 227:
221 SECTION 13 - Marine ProductsDet
Page 228 and 229:
223 SECTION 13 - Marine ProductsDJM
Page 230 and 231:
225 SECTION 13 - Marine ProductsCle
Page 232 and 233:
227 SECTION 13 - Marine ProductsPat
Page 234 and 235:
229 SECTION 14- Tools & Miscellaneo
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
show all

General Products - ALP Industries Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?