General Products - ALP Industries Inc.

Magnetic Lift DevicesCM Series - ToterThe TOTER is a compact, self-contained, lifting magnet whichuses permanent magnets that maintain holding power indefinitely.Within the steel housing are powerful ceramic magnets whose fieldis controlled by the “on-off” position of the handle.Because no electric power is required, TOTERs can operate completelyfree of the restriction of power cords, and can be used whereelectric power is not readily available.RECOMMENDED APPLICATIONSPermanent lifting magnets require good surface conditions toachieve maximum lifting.SECTION 10 - Below-The-Hook Accessories 194The TOTER is ideally suited for in-plant handling, loading andunloading machine tools, and is commonly found in industrial plants,machine shops and warehouses.When greater holding capacity is required, refer to our WBM, WBBattery Magnets, or Circular Electric Magnets also in this catalog.The maximum rated lift is based upon lifting clean, smooth, flat,low-carbon steel plate, 1-1/2” or thicker with the full area of the magnet’slifting surface in contact with the load.Derating is required for plates with rust or scale, plates thinnerthan 1-1/2”, and alloy steels.Please consult the OPERATOR’S MANUAL AND SAFETYINSTRUCTIONS for more detailed ratings.SPECIFICATIONSModel No. CM-400 CM-800Length 7.64”(194mm) 10.95”(278mm)Width 5.67”(144mm) 7.56”(192mm)Height to crane hook 12.4” (315mm) 15.55” (395mm)Net Weight 72.6 lbs. (33 kg) 169.4 lbs. (77kg)Shipping Weight 80 lbs. (36kg) 175 lbs.(80 kg)PERFORMANCE RATING ON AISI 1020 STEELModel CM-4000-880 lbs. (0-400 kg) Rated LiftModel CM-8000-1760 lbs. (0-800 kg) Rated LiftCER SeriesA CER, Circular Electric Lift, magnet is the least costly but most powerful magnet available.Due to deep penetration of its magnetic field, it is less susceptible to adverse surfaceconditions than any other self-contained magnet.RECOMMENDED APPLICATIONSCER magnets are ideally suited for in-plant handling of steel plate, flat stock,castings, forgings or machined components in all types of industrial plants, machineshops, fabricating shops, and steel warehouses. Handling of loose parts such as nuts orbolts is also a popular application.STANDARD FEATURES- Recessed “ON-OFF-RELEASE” switch is protected against accidental operation- Low-carbon steel body for maximum magnetic performance- Built-in solid state rectifier permits operation from 115 volt AC outletAn optional Remote Control with 10’ cable isavailable as an accessory but must be specifiedwith the original order.Maximum rated lift is based upon lifting clean,smooth, flat, low-carbon steel plate, 2” orthicker with the full area of the magnet’s liftingsurface in contact with the load.Model No. Power required at 115/1/60 supply (watts)SPECIFICATIONSNet Weight(lbs.)Dia. Height to hook Rated Lift(lbs.)CER-5 92 22 lbs. 5-1/8” 9-3/4” 0-600 lbs.CER-7 135 41 lbs. 6-3/4” 11-1/4” 0-1200 lbs.CER-9 208 90 lbs. 9” 11-3/4” 0-2400 lbs.CER-12 420 140 lbs. 12” 13-5/8” 0-4400 lbs.CER-16 495 340 lbs. 16” 14-1/2” 0-7250 lbs.CER-20 1050 575 lbs. 20” 15” 0-10500 lbs.FOR MORE INFORMATION CONTACT OUR NEAREST BRANCH OFFICE