General Products - ALP Industries Inc.

More documents

Recommendations

Info

139 SECTION 7 - FittingsHoist RingsAmerican Safety Engineered Hoist RingsCompetitive products are assembled by drilling a holethrough the shoulder pin and securing it to the body with a“roll pin”.ADB uses shoulder pin retainers instead of roll pins tocaptivate the shoulder pins, on sizes up to 10,000 lbs. loadrating. On the larger sizes, we use shoulder pin retainingdowels.What you see below, IS NOT WHAT YOU GET FROMCOMPETITIVE HOIST RINGS!This is ADB’s original patented improved Safety EngineeredHoist Ring.These processes DO NOT require putting a hole throughthe shoulder pin, we use an OD groove. This allows the pinto rotate if necessary without shearing the dowel or clip.ADB uses only hardened dowel pins for assembly of hoistrings. If the shoulder pin should bind against the bail forany reason (accumulation of dirt, rust, improper loadingetc.) the shoulder pin installed with a roll pin is likely toshear, allowing the shoulder pin to come out. This is not thecase with ADB hoist rings.This patented design allows the ADB hoist ring to be disassembled,tested for compliance with safety standardsAND reassembled easily. This is a requirement by somegovernmental agencies. ADB provides the EXTRAS youexpect, at no added cost to you, from the leader of qualitylifting devices. ADB the “original” Safety Hoist Ring.ADB & ONLY ADB CAN OFFER YOU THIS SAFETYADVANTAGE.DON’T ACCEPT LOOK ALIKE IMITATIONS!40 years without a single claim.No other manufacturer can make that statement.American’s Safety Hoist Rings have been design tested.Certified Test Reports are available upon request.SAFETY ENGINEERED HOIST RINGS:• Pivot and swivel to compensate for pitch, roll and swaywhen lifting heavy, unbalanced loads.• Prevent lifting hooks from disengaging.• Made of highest quality alloy steel with certified heat treatment.• Available in 550, 800, 1,000, 2,500, 4,000, 5,000, 7,000,8,000, 10,000, 15,000, 24,000, 30,000, 50,000, 75,000,100,000, 150,000, 200,000 and 250,000 pound safe-loadcapacities ( in any direction).PATENT NO. 3,297,293, 4,705,422 5,848,815FOR MORE INFORMATION CONTACT OUR NEAREST BRANCH OFFICE
SECTION 7 - Fittings 140Safety Engineered Hoist RingsTECHNICAL INFORMATIONHOIST RING MATERIAL: Alloy steel (Certified heat treatment). BlackOxide*.SAFETY FACTORS: 5:1RANGE OF MOVEMENT: 360 o Swivel, 180 o Pivot.INSTALLATION: Tap workpiece for hoist ring screw with axis vertical tomounting surface. Work surface should be flat and smooth to provide full360 degrees flush seating for the bushing flange. (SAFETY NOTE : Someloosening may develop after prolonged service in a permanent installation.It is advisable to periodically re-tighten the mounting screw to maintain thespecified torque value.) The use of free fit spacers between the bushingflange and mounting surface is not recommended as this will reduce the safeload rating on angularly applied loads. Hoist Ring must be free to swivel360 degrees and pivot 180 degrees at all times.*Also available in Nickel or Cad Plated. ( Price per Factory Quotation)All dimensions approximate- variations do not affect use or safety factor.Part Number Rated A B C D E F G H J K L M TL* WeightLoadFoot- Lbs.23050 550 .43 1.61 .71 3/8 .54 2.67 1/4-20 1.84 1.00 .75 .17 1.33 5 5 oz.2305100051 800 .43 1.61 .71 3/8 .29 2.67 5/16-18 1.84 1.00 .75 .17 1.27 7 5 oz.2305200051 800 .43 1.61 .71 3/8 .54 2.67 5/16-18 1.84 1.00 .75 .17 1.27 7 5 oz.2305300051 1000 .43 1.61 .71 3/8 .54 2.67 3/8-16 1.84 1.00 .75 .17 1.21 12 5 oz.2330100051 2500 .70 2.40 .93 1/2 1.07 3.77 1/2-13 2.58 1.49 1.25 .20 1.84 28 1 lb.2300400051 2500 .88 3.25 1.22 3/4 .78 4.78 1/2-13 3.52 1.99 1.50 .16 2.31 28 2 lb. 5 oz.2332200051 2500 .88 3.25 1.22 3/4 .78 6.72 1/2-13 3.52 1.99 1.50 .16 4.25 28 2 lb. 12 oz.2300500051 2500 .88 3.25 1.22 3/4 1.03 4.78 1/2-13 3.52 1.99 1.50 .16 2.31 28 2lb. 5 oz.2332300051 2500 .88 3.25 1.22 3/4 1.03 6.72 1/2-13 3.52 1.99 1.50 .16 4.25 28 2 lb.2300600051 2500 .88 3.25 1.22 3/4 1.28 4.78 1/2-13 3.52 1.99 1.50 .16 2.31 28 2lb. 5 oz.2332400051 2500 .88 3.25 1.22 3/4 1.28 6.72 1/2-13 3.52 1.99 1.50 .16 4.25 28 2 lb. 12 oz.2300100051 4000 .88 3.25 1.22 3/4 .78 4.78 5/8-11 3.52 1.99 1.50 .16 2.18 60 2 lb. 7 oz.2300200051 4000 .88 3.25 1.22 3/4 1.03 4.78 5/8-11 3.52 1.99 1.50 .16 2.18 60 2 lb. 7 oz.2332000051 4000 .88 3.25 1.22 3/4 1.03 6.72 5/8-11 3.52 1.99 1.50 .16 4.12 60 2 lb. 14 oz.2300300051 4000 .88 3.25 1.22 3/4 1.28 4.78 5/8-11 3.52 1.99 1.50 .16 2.18 60 2 lb. 7 oz.2332100051 4000 .88 3.25 1.22 3/4 1.28 6.72 5/8-11 3.52 1.99 1.50 .16 4.12 60 2 lb. 14 oz.2300700051 5000 .88 3.25 1.22 3/4 1.03 4.78 3/4-10 3.52 1.99 1.50 .16 2.06 100 2 lb. 9 oz2332500051 5000 .88 3.25 1.22 3/4 1.03 6.72 3/4-10 3.52 1.99 1.50 .16 4.00 100 3 lb2300900051 5000 .88 3.25 1.22 3/4 1.53 4.78 3/4-10 3.52 1.99 1.50 .16 2.06 100 2 lb. 9 oz2332700051 5000 .88 3.25 1.22 3/4 1.53 6.72 3/4-10 3.52 1.99 1.50 .16 4.00 100 3 lb2310200051 7000 1.40 4.80 1.71 1” 1.04 6.52 3/4-10 5.14 3.00 2.37 .24 3.06 100 6 lb. 10 oz.23329 7000 1.40 4.80 1.71 1” 1.04 8.11 3/4-10 5.14 3.00 2.37 .24 4.65 100 7 lb. 4 oz.2310300051 7000 1.40 4.80 1.71 1” 1.54 6.52 3/4-10 514 3.00 2.37 .24 3.06 100 6 lb. 10 oz23330 7000 1.40 4.80 1.71 1” 1.54 8.11 3/4-10 5.14 3.00 2.37 .24 4.65 100 6 lb. 10 oz.2310100051 8000 1.40 4.80 1.71 1” 1.04 6.52 7/8-9 5.14 3.00 2.37 .24 2.93 160 6 lb. 12 oz.2332800051 8000 1.40 4.80 1.71 1” 1.04 8.11 7/8-9 5.14 3.00 2.37 .24 4.52 160 6 lb. 12 oz2310500051 10000 1.40 4.80 1.71 1” 1.29 6.52 1”-8 5.14 3.00 2.37 .24 2.81 230 7 lb.2333100051 10000 1.40 4.80 1.71 1” 1.29 8.11 1”-8 5.14 3.00 2.37 .24 4.40 230 7 lb.2310600051 10000 1.40 4.80 1.71 1” 1.54 6.52 1”-8 5.14 3.00 2.37 .24 2.81 230 7 lb.2333200051 10000 1.40 4.80 1.71 1” 1.54 8.11 1”-8 5.14 3.00 2.37 .24 4.40 230 7 lb.2310700051 10000 1.40 4.80 1.71 1” 2.29 6.52 1”-8 5.14 3.00 2.37 .24 2.81 230 7 lb.2333300051 10000 1.40 4.80 1.71 1” 2.29 8.11 1”-8 5.14 3.00 2.37 .24 4.40 230 7 lb.23401 15000 1.75 6.00 2.11 1-1/4 1.89 8.73 1-1/4”-7 6.50 3.76 3.20 .35 4.12 470 14 lb.23202 24000 2.25 8.00 2.81 1-3/4 2.70 12.47 1-1/2”-6 8.55 4.87 4.20 .47 6.41 800 33 lb. 12 oz23200 30000 2.25 8.00 2.81 1-3/4 2.96 12.47 2”-4-1/2 8.55 4.87 4.20 .47 5.41 800 36 lb23501 50000 3.00 10.50 4.09 2-1/4 4.00 16.87 2-1/2”-8 11.67 6.52 5.75 1.12 8.03 2100 87 lb. 8 oz23503 50000 3.00 10.50 4.09 2-1/4 4.00 16.87 2-1/2”-4 11.67 6.52 5.75 1.12 8.03 2100 87 lb. 8 oz23600 75000 3.75 13.00 5.27 2-3/4 5.20 19.50 3”-4 14.15 8.10 7.25 1.00 8.48 4300 166 lb23701 100000 4.00 14.50 6.06 3-1/4 7.00 22.09 3-1/2”-4 15.90 8.60 7.75 1.09 9.28 6600 240 lbFOR MORE INFORMATION CONTACT OUR NEAREST BRANCH OFFICE
Page 2 and 3:
Corporate HistoryIn 1981 Reitzel Sw
Page 4 and 5:
TABLE OF CONTENTSWIRE ROPEGeneral I
Page 6 and 7:
1 SECTION 1 - Wire RopeWIRE ROPEGen
Page 8 and 9:
3 SECTION 1 - Wire Ropebeen applied
Page 10 and 11:
5 SECTION 1 - Wire Ropeends will be
Page 12 and 13:
7 SECTION 1 - Wire RopeTroubleshoot
Page 14 and 15:
9 SECTION 1 - Wire RopeSuggested Wi
Page 16 and 17:
11 SECTION 1 - Wire RopeRopesWire R
Page 18 and 19:
13 SECTION 1 - Wire RopeSix Strand
Page 20 and 21:
15 SECTION 1 - Wire RopeRotation Re
Page 22 and 23:
17 SECTION 1 - Wire RopeGalvanized
Page 24 and 25:
19 SECTION 1 - Wire RopeBethlehem8-
Page 26 and 27:
21 SECTION 1 - Wire RopeBridonEndur
Page 28 and 29:
23 SECTION 1 - Wire RopeBridonEndur
Page 30 and 31:
25 SECTION 1 - Wire RopeWireco7-FLE
Page 32 and 33:
27 SECTION 1 - Wire RopeSling Capac
Page 34 and 35:
29 SECTION 1 - Wire RopeSling Capac
Page 36 and 37:
31 SECTION 1 - Wire RopeTerminal Ef
Page 38 and 39:
33 SECTION 2 - Elevator ProductsBet
Page 40 and 41:
35 SECTION 2 - Elevator ProductsBet
Page 42 and 43:
37 SECTION 2 - Elevator ProductsRee
Page 44 and 45:
39 SECTION 2 - Elevator ProductsGov
Page 46 and 47:
41 SECTION 2 - Elevator ProductsWir
Page 48 and 49:
43 SECTION 3 - ChainCHAINTypes of C
Page 50 and 51:
45 SECTION 3 - ChainWelded Single C
Page 52 and 53:
47 SECTION 3 - ChainWelded Quadrupl
Page 54 and 55:
49 SECTION 3 - ChainCrosby ELIMINAT
Page 56 and 57:
51 SECTION 3 - ChainKuplex ® II Ku
Page 58 and 59:
53 SECTION 3 - ChainCrosby ® Grade
Page 60 and 61:
55 SECTION 3 - ChainCrosby 8/10 TM
Page 62 and 63:
57 SECTION 3 - ChainA-1355 Chain Ch
Page 64 and 65:
59 SECTION 3 - ChainRecommended Cha
Page 66 and 67:
61 SECTION 3 - ChainTable of WearCh
Page 68 and 69:
63 SECTION 3 - ChainGrade 70 Transp
Page 70 and 71:
65 SECTION 3 - ChainBinders & Chain
Page 72 and 73:
67 SECTION 4 - Mesh SlingsAlloy Cha
Page 74 and 75:
69 SECTION 5 - Synthetic SlingsCons
Page 76 and 77:
71 SECTION 5 - Synthetic SlingsSaf-
Page 78 and 79:
73 SECTION 5 - Synthetic SlingsPenc
Page 80 and 81:
75 SECTION 5 - Synthetic SlingsWeb
Page 82 and 83:
77 SECTION 5 - Synthetic SlingsTypi
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
83 SECTION 5 - Synthetic SlingsBrai
Page 90 and 91:
85 SECTION 6 - Cargo ControlCARGO C
Page 92 and 93:
87 SECTION 6 - Cargo ControlSafety
Page 94 and 95: 89 SECTION 6 - Cargo ControlBuckle
Page 96 and 97: 91 SECTION 6 - Cargo ControlWinches
Page 98 and 99: 93 SECTION 6 - Cargo ControlFlat Ho
Page 100 and 101: 95 SECTION 6 - Cargo Control“E”
Page 102 and 103: 97 SECTION 7 - FittingsG-450 Crosby
Page 104 and 105: 99 SECTION 7 - FittingsG-429 Crosby
Page 106 and 107: 101 SECTION 7 - FittingsG-340 & S-3
Page 108 and 109: 103 SECTION 7 - FittingsScrew Pin S
Page 110 and 111: 105 SECTION 7 - FittingsRound Pin S
Page 112 and 113: 107 SECTION 7 - FittingsLarge Bolt
Page 114 and 115: 109 SECTION 7 - FittingsS-320 & s-3
Page 116 and 117: 111 SECTION 7 - FittingsShank HookS
Page 118 and 119: 113 SECTION 7 - FittingsSHUR-LOC ®
Page 120 and 121: 115 SECTION 7 - FittingsS-4320 HOOK
Page 122 and 123: 117 SECTION 7 - FittingsSS-4055 Saf
Page 124 and 125: 119 SECTION 7 - FittingsSpecialty H
Page 126 and 127: 121 SECTION 7 - FittingsThimblesExt
Page 128 and 129: 123 SECTION 7 - FittingsSlip-Thru T
Page 130 and 131: 125 SECTION 7 - FittingsWedge Socke
Page 132 and 133: 127 SECTION 7 - FittingsClosed Spel
Page 134 and 135: 129 SECTION 7 - FittingsCLOSED SWAG
Page 136 and 137: 131 SECTION 7 - FittingsTurnbuckles
Page 138 and 139: 133 SECTION 7 - FittingsJaw & Eye T
Page 140 and 141: 135 SECTION 7 - FittingsHook & Eye
Page 142 and 143: 137 SECTION 7 - FittingsSwivelsEqui
Page 146 and 147: 141 SECTION 7 - FittingsHeavy Duty
Page 148 and 149: 143 SECTION 7 - FittingsEZ-Torque T
Page 150 and 151: 145 SECTION 7 - FittingsElectroline
Page 152 and 153: 147 SECTION 7 - FittingsTYPICAL ASS
Page 154 and 155: 149 SECTION 7 - FittingsCable SizeN
Page 156 and 157: 151 SECTION 7 - FittingsNicopress T
Page 158 and 159: 153 SECTION 7 - FittingsStainless S
Page 160 and 161: 155 SECTION 8 - BlocksBLOCKSWire Ro
Page 162 and 163: 157 SECTION 8 - BlocksDiamond & Ova
Page 164 and 165: 159 SECTION 8 - BlocksCrane Blocks#
Page 166 and 167: 161 SECTION 8 - BlocksOverhaul Ball
Page 168 and 169: 163 SECTION 8 - BlocksTackle Block
Page 170 and 171: 165 SECTION 9 - Hoists, Pullers & W
Page 184 and 185: 179 SECTION 10 - Below-the-Hook Acc
Page 194 and 195:
189 SECTION 10 - Below-the-Hook Acc
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
207 SECTION 11 -CordageNylonBlue St
Page 214 and 215:
209 SECTION 11 -CordageRope Use Ref
Page 216 and 217:
211 SECTION 12 - Fall RestraintUniv
Page 218 and 219:
213 SECTION 12 - Fall RestraintSusp
Page 220 and 221:
215 SECTION 13 - Marine ProductsMAR
Page 222 and 223:
217 SECTION 13 - Marine ProductsLig
Page 224 and 225:
219 SECTION 13 - Marine ProductsCha
Page 226 and 227:
221 SECTION 13 - Marine ProductsDet
Page 228 and 229:
223 SECTION 13 - Marine ProductsDJM
Page 230 and 231:
225 SECTION 13 - Marine ProductsCle
Page 232 and 233:
227 SECTION 13 - Marine ProductsPat
Page 234 and 235:
229 SECTION 14- Tools & Miscellaneo
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
show all

General Products - ALP Industries Inc.

Create successful ePaper yourself

Delete template?

Save as template?