DMP XR200 - Allied Fire & Security

More documents

Recommendations

Info

Special Security Command TonesYour keypad also contains a small speaker that allows it to alert youto events as they occur on your system. Below are brief descriptionsof the different tones you'll hear from the keypad:Fire Alarm tone: An intermittent sweeping siren that sounds untilthe fire alarm is silenced, on LCD keypads only.Burglary Alarm tone: A constant siren tone at maximum volumethat continues until the alarm is silenced, on LCD keypads only.Key press tone: A short beep each time you press a key on thekeypad and it’s acknowledged by the system.Prewarn tone: A continuous pulsed tone that sounds when youopen an entry delay door on a system that is armed (turned on)reminding you to disarm the burglary protection.Monitor tone: A pulsed tone for one second, one pulse only thatsounds whenever a door or window is opened while you’re using thezone monitor function from the User Menu. LCD keypads sound adoor bell chime. See Zone Monitor.Trouble tone: A steady tone indicating a trouble condition on yoursystem. Press a SELECT key to silence.What to do when the trouble tone is soundingYou can silence the trouble tone by pressing any one of the toprow SELECT keys. This only silences the keypad and doesnot correct the condition that originally caused the trouble.Understanding Security System TermsThroughout this guide, and in some displays on your keypad, you’llsee certain words or phrases that might be unfamiliar. Althoughevery effort has been made to use terms that are commonly known,there are some for which there was no acceptable substitute.Below are some terms you’ll see here and on your keypad display:ArmingThis is the term used for turning on the burglary protection in one ormore areas of the system. Your system may require you to enter auser code. When armed, the system is able to sound alarm bells orsirens and, if monitored, send alarm reports to a central station whena burglary zone is tripped.Fire, panic, and other 24 hour devices are always turned on and donot need to be armed.DisarmingThis means turning off one or more areas of the system. Whendisarmed, the system does NOT sound alarms or send alarmreports to a central station when a burglary zone is faulted.ZoneA zone refers to one or more protected openings (doors or windows)or protection devices (motion or glassbreak detectors) groupedtogether under the same zone name and number.Often, similar devices in the same general area will share the samezone. For example, the windows on the east side of the premisescan all be grouped together in a zone named E. WINDOWS.4IntroductionSpecial Security Command TonesYour keypad also contains a small speaker that allows it to alert youto events as they occur on your system. Below are brief descriptionsof the different tones you'll hear from the keypad:Fire Alarm tone: An intermittent sweeping siren that sounds untilthe fire alarm is silenced, on LCD keypads only.Burglary Alarm tone: A constant siren tone at maximum volumethat continues until the alarm is silenced, on LCD keypads only.Key press tone: A short beep each time you press a key on thekeypad and it’s acknowledged by the system.Prewarn tone: A continuous pulsed tone that sounds when youopen an entry delay door on a system that is armed (turned on)reminding you to disarm the burglary protection.Monitor tone: A pulsed tone for one second, one pulse only thatsounds whenever a door or window is opened while you’re using thezone monitor function from the User Menu. LCD keypads sound adoor bell chime. See Zone Monitor.Trouble tone: A steady tone indicating a trouble condition on yoursystem. Press a SELECT key to silence.What to do when the trouble tone is soundingYou can silence the trouble tone by pressing any one of the toprow SELECT keys. This only silences the keypad and doesnot correct the condition that originally caused the trouble.Understanding Security System TermsThroughout this guide, and in some displays on your keypad, you’llsee certain words or phrases that might be unfamiliar. Althoughevery effort has been made to use terms that are commonly known,there are some for which there was no acceptable substitute.Below are some terms you’ll see here and on your keypad display:ArmingThis is the term used for turning on the burglary protection in one ormore areas of the system. Your system may require you to enter auser code. When armed, the system is able to sound alarm bells orsirens and, if monitored, send alarm reports to a central station whena burglary zone is tripped.Fire, panic, and other 24 hour devices are always turned on and donot need to be armed.DisarmingThis means turning off one or more areas of the system. Whendisarmed, the system does NOT sound alarms or send alarmreports to a central station when a burglary zone is faulted.ZoneA zone refers to one or more protected openings (doors or windows)or protection devices (motion or glassbreak detectors) groupedtogether under the same zone name and number.Often, similar devices in the same general area will share the samezone. For example, the windows on the east side of the premisescan all be grouped together in a zone named E. WINDOWS.4Introduction
Understanding Security System TermsEntry or Exit zoneAlmost all systems have one or more doors through which you canenter or exit the premises. These doors are programmed with adelay time to allow you to enter or exit without setting off the alarm.When you arm the system, activity on this zone is ignored until theprogrammed exit delay time expires. Once that time has expired andthe system is fully armed, opening the door causes the panel to startthe entry delay time. During the entry delay time, you must enter avalid user code to disarm the system or an alarm will occur.Instant ZoneExterior windows and non entry doors, or interior protection devices,are typically not programmed with delay times. If these zones aretripped while the system is armed, an alarm occurs instantly.24 Hour ZoneA 24 hour zone is not turned on or off by arming or disarming yoursystem. Some examples of 24 hour zones are: fire zones, paniczones, and temperature control zones.AreasAn area is made up of burglary zones that can be armed or disarmedtogether. One area might consist of the office doors and windows.When you arm the office, these zones arm together and sound analarm if opened.Central Station MonitoringYour system can also be programmed to automatically send alarm,trouble, and arming and disarming reports to a central station.Operators at the central station can in turn dispatch the appropriateauthorities or contact you with the specific event information.StatusStatus is a feature that automatically displays the armed or disarmedstatus of your system on the Security Command keypads. Alarm ortrouble conditions on a zone or a system monitor such as AC orbattery trouble can also be displayed. There are two types of statusinformation available: Armed Status and Status List.Armed StatusWith Armed Status, the keypad displays the current armed conditionof areas within your security system. For example:When you arm areas 1 to 4, the keypad shows = 1 2 3 4When you arm areas 1 and 3, the keypad shows = 1 3If your system is setup as an All/Perimeter or Home/Away systemand both the interior and perimeter is armed the display reads:ALL SYSTEM ONStatus ListThe keypad Status List displays any alarm or trouble condition on azone, and any trouble condition on an internal system monitor. Thesystem monitors include the AC power, battery power, panel boxtamper, printer, and phone lines. If more than one alarm or troublecondition occurs at the same time, the keypad sequences thisinformation on its display.If the alarm is from a 24 hour zone or a system monitor, it remainsin the Status List until it restores. If one or more armed burglaryzones trip at the same time, the last one to trip remains in the StatusList. This is to ensure that if a burglary has occurred the last zonetripped remains displayed even if it has been restored.Introduction 5Understanding Security System TermsEntry or Exit zoneAlmost all systems have one or more doors through which you canenter or exit the premises. These doors are programmed with adelay time to allow you to enter or exit without setting off the alarm.When you arm the system, activity on this zone is ignored until theprogrammed exit delay time expires. Once that time has expired andthe system is fully armed, opening the door causes the panel to startthe entry delay time. During the entry delay time, you must enter avalid user code to disarm the system or an alarm will occur.Instant ZoneExterior windows and non entry doors, or interior protection devices,are typically not programmed with delay times. If these zones aretripped while the system is armed, an alarm occurs instantly.24 Hour ZoneA 24 hour zone is not turned on or off by arming or disarming yoursystem. Some examples of 24 hour zones are: fire zones, paniczones, and temperature control zones.AreasAn area is made up of burglary zones that can be armed or disarmedtogether. One area might consist of the office doors and windows.When you arm the office, these zones arm together and sound analarm if opened.Central Station MonitoringYour system can also be programmed to automatically send alarm,trouble, and arming and disarming reports to a central station.Operators at the central station can in turn dispatch the appropriateauthorities or contact you with the specific event information.StatusStatus is a feature that automatically displays the armed or disarmedstatus of your system on the Security Command keypads. Alarm ortrouble conditions on a zone or a system monitor such as AC orbattery trouble can also be displayed. There are two types of statusinformation available: Armed Status and Status List.Armed StatusWith Armed Status, the keypad displays the current armed conditionof areas within your security system. For example:When you arm areas 1 to 4, the keypad shows = 1 2 3 4When you arm areas 1 and 3, the keypad shows = 1 3If your system is setup as an All/Perimeter or Home/Away systemand both the interior and perimeter is armed the display reads:ALL SYSTEM ONStatus ListThe keypad Status List displays any alarm or trouble condition on azone, and any trouble condition on an internal system monitor. Thesystem monitors include the AC power, battery power, panel boxtamper, printer, and phone lines. If more than one alarm or troublecondition occurs at the same time, the keypad sequences thisinformation on its display.If the alarm is from a 24 hour zone or a system monitor, it remainsin the Status List until it restores. If one or more armed burglaryzones trip at the same time, the last one to trip remains in the StatusList. This is to ensure that if a burglary has occurred the last zonetripped remains displayed even if it has been restored.Introduction 5
Page 4 and 5: Emergency Evacuation PlansThe Natio
Page 6 and 7: POWERPOWERThe Security Command Keyp
Page 10 and 11: General Arming OperationYour system
Page 12 and 13: Area System DisarmingDisarming: Whi
Page 15 and 16: Home/Away System ArmingArea Assignm
Page 17 and 18: Security Command User MenuMany of t
Page 19 and 20: Door AccessUser Code Level: 1 and 2
Page 21 and 22: Zone Status continued8. At the ZONE
Page 23 and 24: System StatusUser Code Level: 1 and
Page 25 and 26: User Codes continuedProgramming Cus
Page 27 and 28: SchedulesUser Code Level: 7 and abo
Page 29 and 30: Relay Output SchedulesThe Schedules
Page 31 and 32: Setting the Date and TimeUser Code
Page 33 and 34: About the Display Events SectionThi
Page 35 and 36: Door Access Event DisplaysThis disp
Page 37 and 38: System SetupWe've provided this Sys
Page 39 and 40: User CodesDepending on how your sys
Page 41 and 42: Frequently asked questionsThis sect
Page 43 and 44: Access the User Menu. PressCOMMAND
Page 45 and 46: Start HereUSER CODES?Access the Use
Page 47 and 48: Start HereUSER CODES?Access the Use
Page 49 and 50: POWERPOWER POWER POWERPOWERPOWER PO
Page 51 and 52: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 53 and 54: FA100 User's GuideThese instruction
Page 55: LT-0287 (11/97)LT-0287 (11/97)

DMP XR200 - Allied Fire & Security

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?