XTreme EFIS - STRATOMASTER Instrumentation MGL Avionics

More documents

Recommendations

Info

XTreme-EFIS Operating Manual Page 24Timer:The Timer can be configured in the quick select menu.Hobbs:The XTreme contains a password protected Hobbs timer. The Hobbs time can be set to the current known engine time inthe “TIMERS SETUP” menu. The Hobbs timer will only increment when the RPM is greater then the “HOBBS MINIMUMRPM”.Maintenance:This timer is set in engine hours and it will count down to zero when the engine RPM is greater then the “HOBBSMINIMUM RPM” value as set in the “TIMERS SETUP”. A good use for this function is to set the hours until your nextspark plug change or engine inspection.The purpose of this function is to assist you in determining remaining hours until maintenance will be required. It is notintended as a replacement for the aircraft's maintenance log. It is therefore important that the aircraft's maintenance logbe maintained in the normal manner. You should further use your own discretion in performing maintenance earlier thanindicated should any aircraft performance problems arise.A maximum of 999 hours can be entered as a maintenance interval. Areminder message will appear on startup when zero hours areremaining. The reminder message will automatically disappear after 10seconds or if the pilot presses any key. Engine running time for thepurpose of the maintenance timer is defined as the run time where the engine RPM is greater than the “HOBBSMINIMUM RPM” value as set in the “TIMERS SETUP”.Airframe:This timer operates similar to the engine maintenance timer but is based on flight time. You might use it to schedulethorough airframe checks at intervals..A reminder message will appear on startup when zero hours are remaining. Thereminder message will automatically disappear after 10 seconds or if the pilotpresses any key.3.8.11 Information area 2Volts:The XTreme can measure the supply voltage up to 30Vdc. The supply volts parameters can be configured in the “VOLTSSETUP” menu.OAT:Outside air temperature can be measured using the external temperature probe. The OAT parameters can be configuredin the “OAT SETUP” menu.Glide Ratio:Glide ratio can be measured up to 1:99. Glide ratio is measured as a ratio between forward movement of the aircraft vs.vertical sink rate. Please note that the forward movement of the aircraft is not synonymous with horizontal forwardmovement relative to the earth surface but is a function of airspeed.
XTreme-EFIS Operating Manual Page 25Climb Ratio:Climb ratio can be measured up to 1:99. Climb ratio is measured as a ratio between forward movement of the aircraft vs.vertical climb rate. Please note that the forward movement of the aircraft is not synonymous with horizontal forwardmovement relative to the earth surface but is a function of airspeed.Barometer:Ambient pressure can be displayed in either millibar (mb) or in Inches of Mercury (“Hg). The setup for the “PRESSUREUNIT” in the “ALTITUDE SETUP” menu will determine which.3.8.12 Navigation DisplayPlease see section 3.6.2 for more information.
Page 1 and 2: XTreme - EFISElectronic Flight Info
Page 3 and 4: XTreme-EFIS Operating Manual Page 3
Page 23: XTreme-EFIS Operating Manual Page 2
Page 75 and 76:
XTreme-EFIS Operating Manual Page 7
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
show all

XTreme EFIS - STRATOMASTER Instrumentation MGL Avionics

Create successful ePaper yourself

Delete template?

Save as template?