ACCU-DART User Manual

More documents

Recommendations

Info

InstallationSite Inspection:A site inspection allows you to evaluate your area of operation to ensure adequate communication between the RFTerminal(s) and the Base Station(s).To perform a site inspection, all that is required is a base station and power supply, and an RF Terminal.1. Connect the base station to an A/C power outlet where you think the base station will be placed. Formaximum range, it is generally recommended to place the base station upside down on the ceiling – in the middle ofthe building2. Turn on the RF Terminal3. Press “NO” at the SIGN ON? Prompt4. Press “NO” at the SETUP MODE? Prompt5. Press “NO” at the ONE WAY MODE? Prompt6. Press “YES” at the SITE TESTING? Prompt7. Now you can walk around the building and press “ENTER” when you want to perform the test. Theterminal indicates the percentage of successful transmissions8. If the percentage is at least 85%, then you will have excellent results in the location tested. If you are notachieving the minimum percentage, consult the Worth Data Owner’s Guide for possible solutions.Radio-Frequency Hardware Configuration:**Please consult the Worth Data Owner’s Guide for detailed information on how to configure the base station(s) andRF terminal(s)**Base Stations:You can configure multiple RF terminals per base station. For optimal performance, it is not recommended to exceed8-10 RF terminals on a single base station. If you require more than 8-10 RF terminals, it is recommended to purchaseadditional base stations and divide the RF terminals among them.If you are using multiple base stations, there are two configuration options available. You can attach more than onebase station to a single computer – if there are multiple serial ports on that computer; alternatively you can attacheach base station to a separate computer. The second configuration allows staff to continue working with ACCU-DART, should one computer become unavailable for any reason.Each base station must have a unique channel (or frequency). By default, the channel is set to 0. To confirm thechannel on a base station, unplug the power supply and then plug it in again. The light will blink 3 times plus thechannel number. For example: if the channel is 1, it will blink 4 times.To change the channel (or frequency) of the base station, refer to Appendix A in the Worth Data Owner’s Manual:Channel and Jumper Changes.The Base station(s) plug into the COM port of your computer. If your computer does not have a COM port, you canuse a USB to Serial Cable adaptor. We recommend the Keyspan USA-19HS.(http://www.keyspan.com/products/usb/USA19HS/homepage.spml)RF Terminals:To Begin Setup Mode:1. Turn on the RF Terminal and press any key
2. Press “NO” at the SIGN ON? Prompt3. Press “YES” at the SETUP MODE? Prompt4. Enter the password: “WDTRI” by typing the letters on the keypad (note that the RF Terminal is alreadyshifted to using letters).RF terminals must have unique terminal IDs for each base station. RF terminal IDs are set to 0 by default. When youturn on the RF Terminal, the opening screen will display the terminal ID.To change the RF terminal ID:1. In Setup Mode (see above), press “1” for RF Terminal Setup2. Press “0” for RF Setup3. The first information displayed is the RF Terminal ID. Simply type in a new ID number for this terminal. ForACCU-DART, RF Terminal IDs can be single characters from 0-9 or A-F.4. The new ID number/letter will now be shown.5. Press “F1” to save your changes and go back to the Setup Mode MenuTo increase the efficiency of your operation, you may want to set the RF Terminal(s) to skip the opening screens andautomatically start at the ACCU-DART login screen (instead of the RF Terminal sign-on screens).To skip the opening screens:1. In Setup Mode (see above), press “1” for RF Terminal Setup2. Press “0” for RF Setup3. Press “ENTER” to skip past RF Terminal ID, RF Channel, and Security Code options to Skip Opening Screen4. Press “1” for Go to Two-Way Mode (or sign-on)5. Press “F1” to save your changes and go back to the Setup Mode MenuACCU-DART makes use of the arrow keys, including Begin and End. To enable these keys:1. In Setup Mode (see above), press “1” for RF Terminal Setup2. Press “6” for Other3. Press “ENTER” to skip past options until Control Keys Only4. Press “1” to enable Control Keys/Arrow Keys5. Press “F1” to save your changes and go back to the Setup Mode Menu6. Press “F1” to exit the SETUP MODE and sign on to the systemACCU-DART Software InstallationYour copy of ACCU-DART should include the setup program (setup.exe) and at least one authorization file (RF.ECI forthe RF version, and/or RFNO.ECI for the Desktop version). Sage Accpac users will also require an activation key toactivate their software.1. Send a print-screen capture of the registered company information (including Database ID for SageAccpac users) to info@accu-dart.com to receive the authorization files and activation key.2. Run the Setup Program3. Copy the authorization file(s) (RF.ECI and/or RFNO.ECI) into the appropriate directory:a. For older versions of AccountMate – copy into the VAMSQL directoryb. For newer versions of AccountMate – copy into the AMSQL/ACCU-DART directoryc. For Sage Accpac users – copy into the RF53 or RF54 directories (as appropriate) where SageAccpac is installed4. Set-up the warehouses and users in the maintenance Tab. See the next section for instructions.5. You can now run the ACCU-DART application**Sage Accpac users will be prompted to enter their activation key upon running ACCU-DART for the first time.
Page 1 and 2: ACCU-DARTUser ManualA g u i d e t o
Page 3: IntroductionAbout ACCU-DART:ACCU-DA
Page 7 and 8: Warehouse Maintenance1. Double clic
Page 9 and 10: Here is an example of user 1, Joe B
Page 11 and 12: 4. Vendor Bar Code Maintenance: Thi
Page 13 and 14: ACCU-DART ModulesShip Sales OrdersD
Page 15 and 16: Physical Inventory CountDescription
Page 17 and 18: In-Transit Warehouse Transfers (two
Page 19 and 20: IC ReceiptsDescription:This functio
Page 21 and 22: Commit Sales OrderDescription:This
Page 23 and 24: Split/Combine LotsDescription: This
Page 25 and 26: MISys PO ReceiptDescription:Instruc
Page 27 and 28: Inquiry ModulesItem/Location Inquir
Page 29 and 30: MISys Item/Location InquiryDescript
Page 31: Setting up an OE Miscellaneous Char

ACCU-DART User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?