Sound & Parameter List - Roland

Effects editing parametersParameter Value DescriptionRepeat Rate#10–127 Tape speedIncreasing this value will shortenthe spacing of the delayedsounds.Intensity #2 0–127 Amount of delay repeatsBass -15– +15 Boost/cut for the lower range of theecho soundTreble -15– +15 Boost/cut for the upper range of theecho soundHead S Pan L64–63R Independent panning for the short,Head M PanHead L PanTape DistortionWow/FlutterRate36: FBK PITCH SHIFTER(Feedback Pitch Shifter)This allows the pitch-shifted sound to be fed back into the effect.fig.MFX36middle, and long playback heads0–5 Amount of tape-dependent distortionto be addedThis simulates the slight tonalchanges that can be detected bysignal-analysis equipment. Increasingthis value will increasethe distortion.0–127 Speed of wow/flutter (complexvariation in pitch caused by tapewear and rotational irregularity)0–127 Depth of wow/flutterWow/FlutterDepthEcho Level 0–127 Volume of the echo soundDirect Level 0–127 Volume of the original soundLevel 0–127 Output levelL inR inParameter Value DescriptionMode 1, 2, 3, 4, 5 Setting a higher value for this parameterresults in a slower response,but steadier pitch.Coarse #1 -24– +12semiAdjusts the pitch of the pitch-shiftedsound in semitone steps.Fine -100– +100centAdjusts the pitch of the pitch-shiftedsound in 2-cent steps.Pre Delay 0.0–500 ms Adjusts the time until the pitchshifted sound is heard.Feedback#2-98– +98 % Adjusts the amount of the pitchshiftedsound that’s fed back intothe effect. Negative (-) settings invertthe phase.Pan L64–63R Stereo location of the pitch-shiftedsoundLow Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalancePitch ShifterFeedbackD100:0W–D0:100WBalance DBalance DLevel 0–127 Output level2-BandEQBalance WBalance W2-BandEQL outR outVolume balance between the directsound (D) and the pitch-shiftedsound (W)37: 2Vo PITCH SHIFTER(2-Voice Pitch Shifter)Shifts the pitch of the original sound. This 2-voice pitch shifter hastwo pitch shifters, and can add two pitch-shifted versions of theoriginal sound.fig.MFX37L inR inParameter Value DescriptionMode 1, 2, 3, 4, 5 Setting a higher value for this parameterresults in a slower response,but steadier pitch.Coarse A #1 -24– +12 Adjusts the pitch of Pitch Shift A/BCoarse B #2 semi in semitone steps.Fine A -100– Adjusts the pitch of Pitch Shift A/BFine B +100 cent in 2-cent steps.Pre Delay A 0.0–500 Adjusts the time until Pitch Shift A/Pre Delay B msB is heard.Pan A L64–63R Stereo location of Pitch Shift A/BPan BLevelBalanceA100:0B–A0:100BVolume balance between Pitch ShiftA and Pitch Shift BBalance38: GATED REVERBThis is a special type of reverb in which the reverb is cut off withoutbeing allowed to decay naturally.fig.MFX38D100:0W–D0:100WLevel 0–127 Output levelL inR inLevel Balance A2Voice Pitch ShifterLevel Balance BBalance DGated ReverbBalance DPanA RPanB LBalance DPanA LPanB RBalance DL outBalance WBalance WR outVolume balance between the directsound (D) and the pitch shiftedsounds (W)2-BandEQBalance WBalance W2-BandEQL outR outParameter Value DescriptionType NORMAL,REVERSEType of reverbNORMAL: conventional gatedreverbREVERSE: backwards reverbPre Delay 0.0–100.0msAdjusts the time until the reverbsound is heard.Time 5–500 ms Adjusts the time from when the reverbis first heard until it disappears.Pan #1 L64–63R Stereo location of the reverb soundLow Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalance #2 D100:0W–D0:100WVolume balance between the directsound (D) and the reverb sound (W)Level 0–127 Output level39