IC-M402 - ICOM Canada

More documents

Recommendations

Info

BAS<strong>IC</strong> OPERATION3■ DescriptionDualwatch monitors Ch 16 while you are receiving an-otherchannel; tri-watch monitors Ch 16 and the call channel whilereceiving another channel.DUALWATCH/TRI-WATCH SIMULATIONCall channel[Example]:Operating dualwatch on INTCh 25Dual-watchstarts.Signal receivedon channel 16takes priority.Operating tri-watch on INTCh 25Tri-watchstarts.Signal isreceived oncall channel.DualwatchTri-watch•If a signal is received on Channel 16, dualwatch/tri-watch pauseson Ch 16 until the signal disappears.•If a signal is received on the call channel during tri-watch, tri-watchbecomes dualwatch until the signal disappears.•To transmit on the selected channel during dualwatch/tri-watch, pushand hold [PTT].Dual-watchresumes afterthe signaldisappears.Signal receivedon channel 16takes priority.Tri-watchresumes afterthe signaldisappears.■ Operationq Select the desired operating channel.w Select dualwatch or tri-watch in set mode. (p. 20)e Push [CH/WX] for 1 sec. to start dualwatch or tri-watch.•“DW” appears during dualwatch; “TW” appears during tri-watch.•Beep tone sounds when a signal is received on Channel 16.r To cancel dualwatch/tri-watch, push [CH/WX] again.8
5 SCAN OPERATIONS■ Setting tag channelsFor more efficient scanning, add desired channels as tagchannels or clear tag channels for unwanted channels. Channelsset as non-tag channels will be skipped during scanning.Tag channels can be assigned to each channel group(U.S.A., International, <strong>Canada</strong>) independently.q While pushing [H/L], push [CH/WX] one or more times toselect the desired channel group, if desired.w Select the desired channel to set as a tag channel.e Push [Y] and [Z] simultaneously for 1 sec. to set the displayedchannel as a tag channel.•“TAG” appears in the function display.r To cancel the tag channel setting, repeat e .•“TAG” disappears.•Clearing all tag channels in the selected channel group➥While pushing [Y] and [Z], Turn power ON to clear all tagchannels in the channel group.■ Starting a scanSet scan type (priority or normal scan) and scan resume timerin advance using set mode. (p. 20)q Set tag channels as described at left.w Make sure the squelch is closed to start a scan.e While pushing [H/L], push [CH/WX] one or more times toselect the desired channel group, if desired.r Push [Y] or [Z] for 1 sec. to start priority or normal scan.•“Pri scan 16” or “Normal scan” appears in the function display.•When a signal is detected, scan pauses until the signal disappearsor resumes after pausing 5 sec. according to set mode setting.(Channel 16 is still monitored during priority scan.)•While in the scanning, use [Y] and [Z] key to check tag channels,change the scanning direction or resume the scan manually.•“16” flashes and a beep tone sounds when a signal is receivedon Channel 16 during priority scan.•Push [Y] and [Z] for 1 sec. to set the paused channel as a tagchannel.t To stop the scan, push [Y] or [Z].[Example]: Starting a priority scan.9Scan starts.When a signal is received
Page 1: INSTRUCTION MANUALVHF MARINE TRANSC
Page 4 and 5: CAUTIONSRWARNING! NEVER connect the
Page 6: TABLE OF CONTENTSFOREWORD .........
Page 9 and 10: 2PANEL DESCRIPTION■ Function disp
Page 11 and 12: 3 BASIC OPERATION■ Channel select
Page 13: 3 BASIC OPERATION■ Call channel p
Page 17 and 18: 6 DSC OPERATION■ MMSI code progra
Page 19 and 20: 6 DSC OPERATION■ Transmitting DSC
Page 21 and 22: 6 DSC OPERATIONïTransmitting posit
Page 23 and 24: 6 DSC OPERATION17■ Receiving DSC
Page 25 and 26: 7 INTERCOM OPERATION (IC-M402 only)
Page 27 and 28: 8 SET MODEïDual/tri watchThis item
Page 29 and 30: 9 INSTALLATION AND MAINTENANCE■ C
Page 31 and 32: 9 INSTALLATION AND MAINTENANCE■ M
Page 33 and 34: 10 HM-127 REMOTE-CONTROL MICROPHONE
Page 45 and 46: 12 CHANNEL LIST39Channel number Fre
Page 47 and 48: 13 SPECIFICATIONS■ Dimensions41
Page 49 and 50: OPTION15■Options• MB-69 FLUSH M

IC-M402 - ICOM Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?