EAGLE CORR PEâ¢ * - JM Eagle

More documents

Recommendations

Info

WarrantyJM Eagle warrants that its standard polyvinyl chloride (PVC), polyethylene(PE), conduit/plumbing/solvent weld and Acrylonitrile-Butadiene-Styrene(ABS) pipe products (“Products”) are manufactured in accordance with applicableindustry specifications referenced on the Product and are free fromdefects in workmanship and materials. Every claim under this warranty shallbe void unless in writing and received by JM Eagle within 30 days of thedate the defect was discovered, and within one year of the date of shipmentfrom the JM Eagle plant. Claims for Product appearance defects, however,must be made within 30 days of the date of the shipment from the JM Eagle plant. Proof of purchase with the date thereof must be presented to thesatisfaction of JM Eagle , with any claim made pursuant to this warranty.JM Eagle must first be given an opportunity to inspect the alleged defectiveProducts in order to determine if it meets applicable industry standards, ifthe handling and installation have been satisfactorily performed in accordancewith JM Eagle recommended practices and if operating conditionsare within standards. Written permission and/or a Return Goods Authorization(RGA) must be obtained along with instructions for return shipment toJM Eagle of any Products claimed to be defective.The limited and exclusive remedy for breach of this Limited Warranty shallbe, at JM Eagle’s sole discretion, the replacement of the same type, size andlike quantity of non-defective Product, or credits, offsets or combination ofthereof, for the wholesale purchase price of the defective unit.This Limited Warranty does not apply for any Product failures caused by user’sflawed designs or specifications, unsatisfactory applications, improperinstallations, use in conjunction with incompatible materials, contact withaggressive chemical agents, freezing or overheating of liquids in the Product,and any other misuse causes not listed here. This Limited Warranty also excludesfailure or damage caused by fire stopping materials, tread sealants, ordamage caused by the fault or negligence of anyone other than JM Eagle ,or any other act or event beyond the control of JM Eagle .JM Eagle’s liability shall not, at any time, exceed the actual wholesale purchaseprice of the Product. The warranties in this document are the only warrantiesapplicable to the Product and there are no other warranties, expressedor implied. This Limited Warranty specifically excludes any liability for general6 EAGLE CORR PE INSTALLATION GUIDE
damages, consequential or incidental damages, including without limitation,costs incurred from removal, reinstallation, or other expenses resulting fromany defect. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESSFOR A PARTICULAR PURPOSE ARE SPECIFICALLY DISCLAIMED ANDJM Eagle SHALL NOT BE LIABLE IN THIS RESPECT NOTWITHSTANDINGJM Eagle’s ACTUAL KNOWLEDGE OF THE PRODUCT’S INTENDED USE.JM Eagle’s Products should be used in accordance with standards setforth by local plumbing and building laws, codes or regulations and theapplicable standards. Failure to adhere to these standards shall void thisLimited Warranty. Products sold by JM Eagle that are manufactured byothers are warranted only to the extent and limits of the warranty of themanufacturer. No statement, conduct or description by JM Eagle or itsrepresentative, in addition to or beyond this Limited Warranty, shall constitutea warranty. This Limited Warranty may only be modified in writingsigned by an officer of JM Eagle .EAGLE CORR PE INSTALLATION GUIDE7
Page 5 and 6: 5.25.35.45.55.66.06.16.26.36.45.1.2
Page 7: Engineers, superintendents, contrac
Page 11 and 12: Figure 21.2 UnloadingJM Eagle's Eag
Page 14 and 15: 1.4 Gasket CareAll Eagle Corr PE p
Page 16 and 17: 2.0 Trench Construction2.1 Working
Page 18 and 19: Table 1Nominal IDIN (mm)Minimum Tre
Page 20 and 21: When sheeting is used, it should be
Page 22 and 23: Figure 8Important: If for any reaso
Page 24: Pipe Joint Homing MethodsPipe joint
Page 27 and 28: Fabrication of an installation stub
Page 29 and 30: Figure 17When Eagle Corr PE must b
Page 31: PIPE SIZEjoints/1 lb of lubricantIN
Page 34 and 35: Cement does not adhere to HDPE. The
Page 36 and 37: Watertight connector (A-Lok )Manhol
Page 38 and 39: ment, and support. Portions of the
Page 40 and 41: loosely placed to provide uniform s
Page 42 and 43: GeneralRecommendationsand Restricti
Page 44 and 45: 1. See ASTM D 2321 or D2487 for det
Page 46 and 47: Correct backfillCorrect backfillUse
Page 48 and 49: When Class II materials are compact
Page 50 and 51: Selection of proper compaction equi
Page 52 and 53: In soils where ground water fluctua
Page 54: minimum cover heightsnominal ID in
Page 57 and 58: Key pipe profile properties that in
Page 59 and 60:
5.6.1 Frozen BackfillPrecautions sh
Page 61 and 62:
Lid & frame specifiedby designer en
Page 63 and 64:
Ground water can prevent proper pla
Page 65 and 66:
practices associated with initial b
Page 67 and 68:
If one split ban coupler cannot com
Page 69 and 70:
• Excavate an area along the leng
Page 71 and 72:
NOTICE TO ALL READERS OF THIS GUIDE
Page 73 and 74:
Notes:EAGLE CORR PE INSTALLATION G
Page 76:
March 2011JME-18B© J-M Manufacturi
show all

EAGLE CORR PEâ¢ * - JM Eagle

Create successful ePaper yourself

Delete template?

Save as template?

EAGLE CORR PEâ¢ * - JM Eagle