DeviceNet Modules, Series 90-30, Manual, GFK-2196

More documents

Recommendations

Info

3Configuring DeviceNet Explicit MessagingExplicit Messaging is the highest priority messaging. Explicit messaging provides access to objectsother than the default I/O connection set, and optionally creates a buffer for explicit connection.Not all slaves support explicit services, and many, including most discrete I/O devices, do not useexplicit services.Some devices rely on Explicit Messaging for configuration of selected parameters. For example,some VersaPoint modules can be configured using Explicit Messaging. To be configured byExplicit Messaging, an Explicit Messaging connection to the device must first be set up as shownbelow.If Explicit Messaging should be enabled, click on Enable Explicit Connection on the ExplicitMessages tab.In addition, for a Series 90-30 DeviceNet Slave Module, or Series 90-30 DeviceNet Master moduleoperating as a slave, specify the message request and message response size. Make sure the sizespecified is large enough. The Series 90-30 DeviceNet modules implement Explicit Messagingthrough the use of COMMREQ instructions in the application program. These COMMREQmessages are described in chapter 6, "Programmed Communications". The messages sizes of eachexplicit message type are described in that chapter.Explicit Messaging Screen for a Series 90-30 DeviceNet Master ModuleGFK-2196 Chapter 3 PLC Configuration for the DeviceNet Master 3-21
Chapter4PLC Configuration for the DeviceNet SlaveThis chapter explains how to add a Series 90-30 DeviceNet Slave Module (IC693DNS201) to theconfiguration of the Series 90-30 PLC. It also explains how to configure communicationsconnections between a Series 90-30 DeviceNet Slave Module and the DeviceNet network.• Configuration Steps• Adding a DeviceNet Slave Module to the PLC Configuration• Configuring the Parameters of a DeviceNet Slave Module• Configuring the Network Settings of a DeviceNet Slave Module• Configuring the MAC ID• Configuring I/O Messaging Connections• Configuring DeviceNet Explicit MessagingThese configuration procedures are written for users who have a basic knowledge of theCIMPLICITY Machine Edition Logic Developer software and the Series 90-30 PLC. For helpwith using the software, please see the software’s built-in help system.Note:The DeviceNet Slave Module is only supported in CIMPLICITY Machine Edition LogicDeveloper. The Logicmaster, VersaPro, and Control software do not support thismodule.GFK-2196 4-1
Page 1 and 2: GE Fanuc AutomationProgrammable Con
Page 4 and 5: ContentsCOMMREQ Programming Require
Page 6 and 7: 1DeviceNet Modules for the Series 9
Page 8 and 9: 1Series 90-30 DeviceNet Master Modu
Page 10 and 11: 1Series 90-30 DeviceNet Slave Modul
Page 12 and 13: 1DeviceNet Communications for Serie
Page 14 and 15: 2Power SuppliesWhen using a Series
Page 16 and 17: 2Bus LengthThe maximum length of th
Page 18 and 19: 2GroundingDeviceNet Cable Grounding
Page 20 and 21: 2Module LEDsThe module's three LEDs
Page 22 and 23: Chapter3PLC Configuration for the D
Page 24 and 25: 3Adding a DeviceNet Master Module t
Page 26 and 27: 3Settings tabFault StateTransmissio
Page 28 and 29: 3Network Settings of a DeviceNet Ma
Page 30 and 31: 3Configuring Network Settings for S
Page 32 and 33: 3Configuring a Polled I/O Messaging
Page 34 and 35: 3Configuring a Change-of-State (COS
Page 36 and 37: 3Configuring DeviceNet Explicit Mes
Page 38 and 39: 3Configuring a Polled I/O Messaging
Page 40 and 41: 3Configuring a Change-of-State (COS
Page 44 and 45: 4Configuration StepsThere are three
Page 46 and 47: 4Configuring the Parameters of a De
Page 48 and 49: 4Data Areas TabsThese tabs show the
Page 50 and 51: 4Configuring I/O Messaging Connecti
Page 52 and 53: 4Configuring a Strobed I/O Messagin
Page 54 and 55: 4Configuring a Cyclic I/O Messaging
Page 56 and 57: Chapter5Module OperationThis chapte
Page 58 and 59: 5The DeviceNet Master Module stores
Page 60 and 61: 5Fault Table Entries for a Series 9
Page 62 and 63: 5Device Status Bits for the Series
Page 64 and 65: 6COMMREQs for the Series 90-30 Devi
Page 66 and 67: 6Format of the Communication Reques
Page 68 and 69: 6Corrective Actions for COMMREQ Err
Page 70 and 71: 6Command Code 9: Reading Identifica
Page 72 and 73: 6Runtime Error Codes in the Module
Page 74 and 75: 6Command Code 4: Getting the Status
Page 76 and 77: 6Command Code 5: Getting Status Inf
Page 78 and 79: 6Command Code 6: Getting Input Stat
Page 80 and 81: 6Command Codes 1 & 7: Sending a Dev
Page 82 and 83: 6Word # Dec (Hex) Description1 0001
Page 84 and 85: 6Send Device Explicit Extended, Dat
Page 86 and 87: 6Command Codes 2, 3 & 8: Reading an
Page 88 and 89: 6Reading a DeviceNet Custom-Explici
Page 90 and 91: 6Command Codes 3 & 8: Replying to a
Page 92 and 93:
6Command Code 8: Send Server Explic
Page 94 and 95:
7Identity ObjectObject Class 0x01Th
Page 96 and 97:
7DeviceNet ObjectObject Class 0x03T
Page 98 and 99:
7Connection ObjectObject Class 0x05
Page 100 and 101:
7PLC Data ObjectObject Class 0x64Nu
Page 102 and 103:
AppendixADeviceNet EDS FilesThis se
Page 104 and 105:
IndexAACK timeout, 3-5, 4-5Add Devi
show all

DeviceNet Modules, Series 90-30, Manual, GFK-2196

Create successful ePaper yourself

Delete template?

Save as template?