TL-SL3428_V3_User_Guide - TP-Link

More documents

Recommendations

Info

7.5 Application Example for STP Function‣ Network Requirements• Switch A, B, C, D and E all support MSTP function.• A is the central switch.• B and C are switches in the convergence layer. D, E and F are switches in the access layer.• There are 6 VLANs labeled as VLAN101-VLAN106 in the network.• All switches run MSTP and belong to the same MST region.• The data in VLAN01, 103 and 105 are transmitted in the STP with B as the root bridge. Thedata in VLAN02, 104 and 106 are transmitted in the STP with C as the root bridge.‣ Network Diagram‣ Configuration Procedure• Configure Switch A:Step Operation Description1 Configure ports On VLAN→802.1Q VLAN page, configure the link typeof the related ports as Trunk, and add the ports to VLAN101 and VLAN 106. The detailed instructions can befound in the section 802.1Q VLAN.2 Enable STP function On Spanning Tree→STP Config→STP Config page,enable STP function and select MSTP version.On Spanning Tree→STP Config→Port Config page,enable MSTP function for the port.3 Configure the region name andthe revision of MST region4 Configure VLAN-to-Instancemapping table of the MST regionOn Spanning Tree→MSTP Instance→Region Configpage, configure the region as TP-LINK and keep thedefault revision setting.On Spanning Tree→MSTP Instance→InstanceConfig page, configure VLAN-to-Instance mappingtable. Map VLAN 101, 103 and 105 to Instance 1; mapVLAN 102, 104 and 106 to Instance 2.87
• Configure Switch B:Step Operation Description1 Configure ports On VLAN→802.1Q VLAN page, configure the link typeof the related ports as Trunk, and add the ports to VLAN101 and VLAN 106. The detailed instructions can befound in the section 802.1Q VLAN.2 Enable STP function On Spanning Tree→STP Config→STP Config page,enable STP function and select MSTP version.On Spanning Tree→STP Config→Port Config page,enable MSTP function for the port.3 Configure the region name andthe revision of MST region4 Configure VLAN-to-Instancemapping table of the MST region5 Configure switch B as the rootbridge of Instance 16 Configure switch B as thedesignated bridge of Instance 2On Spanning Tree→MSTP Instance→Region Configpage, configure the region as TP-LINK and keep thedefault revision setting.On Spanning Tree→MSTP Instance→InstanceConfig page, configure VLAN-to-Instance mappingtable. Map VLAN 101, 103 and 105 to Instance 1; mapVLAN 102, 104 and 106 to Instance 2.On Spanning Tree→MSTP Instance→InstanceConfig page, configure the priority of Instance 1 to be 0.On Spanning Tree→MSTP Instance→InstanceConfig page, configure the priority of Instance 2 to be4096.• Configure Switch C:Step Operation Description1 Configure ports On VLAN→802.1Q VLAN page, configure the link typeof the related ports as Trunk, and add the ports to VLAN101 and VLAN 106. The detailed instructions can befound in the section 802.1Q VLAN.2 Enable STP function On Spanning Tree→STP Config→STP Config page,enable STP function and select MSTP version.On Spanning Tree→STP Config→Port Config page,enable MSTP function for the port.3 Configure the region name andthe revision of MST region4 Configure VLAN-to-Instancemapping table of the MST region5 Configure switch C as the rootbridge of Instance 16 Configure switch C as the rootbridge of Instance 2On Spanning Tree→MSTP Instance→Region Configpage, configure the region as TP-LINK and keep thedefault revision setting.On Spanning Tree→MSTP Instance→InstanceConfig page, configure VLAN-to-Instance mappingtable. Map VLAN 101, 103 and 105 to Instance 1; mapVLAN 102, 104 and 106 to Instance 2.On Spanning Tree→MSTP Instance→InstanceConfig page, configure the priority of Instance 1 to be4096.On Spanning Tree→MSTP Instance→InstanceConfig page, configure the priority of Instance 2 to be 0.88
Page 1 and 2:
TL-SL342824-Port 10/100Mbps + 4-Por
Page 3 and 4:
CONTENTSPackage Contents ..........
Page 5 and 6:
7.4.2 TC Protect...................
Page 7 and 8:
12.3.3 Alarm Config ...............
Page 9 and 10:
Chapter 1 About this GuideThis User
Page 11 and 12:
ChapterChapter 9 QoSChapter 10 ACLC
Page 13 and 14:
Chapter 2 IntroductionThanks for ch
Page 15 and 16:
Note:When using the SFP port with a
Page 17 and 18:
Figure 3-3 Main Setup-MenuNote:Clic
Page 19 and 20:
Indicates the 100Mbps port is at th
Page 21 and 22:
Device Location:System Contact:Ente
Page 23 and 24:
IP Address Mode:Management VLAN:IP
Page 25 and 26:
Password:Confirm Password:Type a pa
Page 27 and 28:
Figure 4-11 Firmware UpgradeNote:1.
Page 29 and 30:
Figure 4-14 Access ControlThe follo
Page 31 and 32:
Figure 4-15 SSL ConfigThe following
Page 33 and 34:
‣ Key DownloadKey Type:Key File:D
Page 35 and 36:
3. On the Web management page of th
Page 37 and 38:
Chapter 5 SwitchingSwitching module
Page 39 and 40:
Figure 5-2 Mirroring PortThe follow
Page 41 and 42:
enabled, the outgoing packets sent
Page 43 and 44: Note:1. The Port Security function
Page 45 and 46: Figure 5-6 LAG TableThe following e
Page 47 and 48: Description:Give a description to t
Page 49 and 50: preferred one. If the two port prio
Page 51 and 52: automatically.Refresh Rate:Enter a
Page 53 and 54: Figure 5-12 Address TableThe follow
Page 55 and 56: Search Option:Select a Search Optio
Page 57 and 58: Select:MAC Address:VLAN ID:Port:Typ
Page 59 and 60: Chapter 6 VLANThe traditional Ether
Page 61 and 62: (2) TRUNK: The TRUNK port can be ad
Page 63 and 64: Figure 6-4 Create or Modify 802.1Q
Page 65 and 66: Link Type:PVID:LAG:VLAN:Select the
Page 67 and 68: 6.2.1 Protocol VLANOn this page, yo
Page 69 and 70: Figure 6-9 Enable Protocol VLAN for
Page 71 and 72: 6.4 Application Example for Protoco
Page 73 and 74: Hold Timer: When a GARP entity rece
Page 75 and 76: Fixed: In this mode, a port cannot
Page 77 and 78: • Port: Port 3 is the root port o
Page 79 and 80: Tips:In a STP with stable topology,
Page 81 and 82: Figure 7-3 Port rolesThe Spanning T
Page 83 and 84: that occur in a specific region bef
Page 85 and 86: Figure 7-6 Port ConfigThe following
Page 87 and 88: Figure 7-7 Region ConfigThe followi
Page 89 and 90: Figure 7-9 Instance Port ConfigThe
Page 91 and 92: A CIST and its secondary root bridg
Page 93: 7.4.2 TC ProtectWhen TC Protect is
Page 97 and 98: ‣ Suggestion for Configuration•
Page 99 and 100: 1. Multicast IP Address:As specifie
Page 101 and 102: The host, running IGMPv1, does not
Page 103 and 104: Figure 8-5 Port ConfigThe following
Page 105 and 106: Select:VLAN ID:Router Port Time:Mem
Page 107 and 108: 5. After a multicast VLAN is create
Page 109 and 110: 8.2.1 Multicast IP TableOn this pag
Page 111 and 112: 8.3 Multicast FilterWhen IGMP Snoop
Page 113 and 114: Max Groups:LAG:Specify the maximum
Page 115 and 116: Chapter 9 QoSQoS (Quality of Servic
Page 117 and 118: Figure 9-4 SP-Mode2. WRR-Mode: Weig
Page 119 and 120: Note:To complete QoS function confi
Page 121 and 122: Priority Level:Indicates the priori
Page 123 and 124: 3 Map the DSCP priority to theprior
Page 125 and 126: Figure 9-11 Storm ControlThe follow
Page 127 and 128: Port Voice VLANModeAutomatic ModeMa
Page 129 and 130: The following entries are displayed
Page 131 and 132: Chapter 10 ACLACL (Access Control L
Page 133 and 134: End Time:Delete:Displays the end ti
Page 135 and 136: The following entries are displayed
Page 137 and 138: 10.2.5 Extend-IP ACLExtend-IP ACLs
Page 139 and 140: Operation:Click the Edit button to
Page 141 and 142: Index:Policy Name:Interface:Directi
Page 143 and 144: 3. The staff of the marketing depar
Page 145 and 146:
Chapter 11 Network SecurityNetwork
Page 147 and 148:
Figure 11-2 Manual BindingThe follo
Page 149 and 150:
Figure 11-4 ARP ScanningThe followi
Page 151 and 152:
Figure 11-6 Interaction between a D
Page 153 and 154:
Choose the menu Network Security→
Page 155 and 156:
11.2 ARP InspectionAccording to the
Page 157 and 158:
Figure 11-11 ARP Attack - Cheating
Page 159 and 160:
The IP-MAC Binding function allows
Page 161 and 162:
The following entries are displayed
Page 163 and 164:
DoS Attack TypeDescriptionScan SYNF
Page 165 and 166:
supplicant system. Note that the cl
Page 167 and 168:
In this mode, packet transmission i
Page 169 and 170:
exchange information between the sw
Page 171 and 172:
Authorized:LAG:Displays the authent
Page 173 and 174:
Chapter 12 SNMP‣ SNMP OverviewSNM
Page 175 and 176:
The User is configured in a SNMP Gr
Page 177 and 178:
12.1.3 SNMP GroupOn this page, you
Page 179 and 180:
Figure 12-6 SNMP UserThe following
Page 181 and 182:
ead-only: Management right of the C
Page 183 and 184:
Figure 12-8 Notification ConfigThe
Page 185 and 186:
The RMON Groups can be configured o
Page 187 and 188:
Figure 12-11 Alarm ConfigThe follow
Page 189 and 190:
Chapter 13 ClusterWith the developm
Page 191 and 192:
The following entries are displayed
Page 193 and 194:
Detail:Click the Detail button to v
Page 195 and 196:
‣ Device TableDevice Type:Device
Page 197 and 198:
Port:NTDP:Displays the port number
Page 199 and 200:
Cluster:Cluster Role:Displays the c
Page 201 and 202:
Individual:Select this option to ch
Page 203 and 204:
4 Configure the member switch On Cl
Page 205 and 206:
Figure 14-1 CPU MonitorClick the Mo
Page 207 and 208:
The Log function is implemented on
Page 209 and 210:
Figure 14-5 Log HostThe following e
Page 211 and 212:
Pair:Status:Length:Error:Displays t
Page 213 and 214:
14.4.2 TracertTracert test function
Page 215 and 216:
Figure 15-2 Open Hyper Terminal2) T
Page 217 and 218:
Figure 15-6 bootUtil MenuAs the pro
Page 219 and 220:
Appendix A: SpecificationsIEEE802.3
Page 221 and 222:
Figure B-25) The following TCP/IP P
Page 223 and 224:
Appendix C: 802.1X Client SoftwareI
Page 225 and 226:
Figure C-5 Install the Program6. Th
Page 227 and 228:
Figure C-8 Preparing Setup3. On the
Page 229 and 230:
Auto reconnect after timeout: Selec
Page 231 and 232:
Appendix D: GlossaryAccess Control
Page 233 and 234:
Layer 2Data Link layer in the ISO 7
show all

TL-SL3428_V3_User_Guide - TP-Link

Create successful ePaper yourself

Delete template?

Save as template?