AN-PR1000H Operation-Manual GB - Sharp

More documents

Recommendations

Info

AN-PR1000HENGLISHReferencesTroubleshooting chart (continued)• If trouble occursWhen this product is subjected to strong external interference (mechanical shock, excessivestatic electricity, abnormal supply voltage due to lightning, etc.) or if it is operatedincorrectly, it may malfunction.If such a problem occurs, do the following:1 Set the unit to the stand-by mode and turn the power on again.2 If the unit is not restored in the previous operation, unplug and plug in the unit, andthen turn the power on.Note:If neither operation above restores the unit, clear all the memory by resetting it.Clearing all the memory (reset)1 Unplug the unit.2 Whilst holding down the FUNCTION button, plug in the AC power lead."RESET" is displayed on the display for about 1 second, the unit is turned off.3 Press the ON/STAND-BY button again to turn the power on.Caution:If the unit is reset, each setting returns to default.When the protection circuit is activated:If the speaker connection lead is short-circuited, the protection circuit will be activated.When the protection circuit functions, the unit is turned off automatically. At that time,the timer indicator blinks.Unplug the AC power lead and plug it in again after 5 minutes or more. Then checkthe operation. (*)Error indicators and warningsWhen you fail to perform operations properly, the following messages are displayedon the unit.DisplayTimer indicatorMeaning• The cooling fan at the rear of the unit doesnot run.Unplug the AC power lead and check if foreignobjects get caught around the coolingfan.• Malfunction of the surround circuit.Place the unit away from noise source andplug the AC power lead into another wallsocket. (*)• Malfunction of circuits other than the surroundcircuit.Place the unit away from noise source andplug the AC power lead into another wallsocket. (*)• When there is no input signal.Play back the connected equipment.• Nonstandard signal. Cannot be recognised.Signals other than DOLBY DIGITAL, DTS,Linear PCM cannot be recognised.• Poor connection of the digital audio inputterminal.Turn off the unit and check if the cable isconnected properly.• When the protection circuit of the amplifieris activated.See left.(*): Should the same message appear even if the unit is unplugged and plugged in oris set to the stand-by mode and on again, contact your local dealer where you purchasedthe unit.E-39
Maintenance• Cleaning the cabinetPeriodically wipe the cabinet with a soft cloth.AN-PR1000HENGLISH• Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage thecabinet finish.• Do not apply oil to the inside of each component. It may cause malfunctions.SpecificationsAs part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performancespecification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.• Main unitAmplifier sectionPower sourcePower consumptionAmplification systemFrequency rangeAC 220 V - 240 V, 50 HzPower on: 80 WPower stand-by: 0.6 WFront speaker: Pulse width modulationSubwoofer: Pulse width modulationFM : 87.5 - 108 MHzOutput power Front speaker: RMS: 150W (75W + 75W) (DIN 45 324)Subwoofer: RMS: 150W (75W + 75W) (DIN 45 324)Audio input terminals Optical digital input (DIGITAL 1/2): Square type 2Coaxial digital input (DIGITAL 3): RCA type 1Analog input (LINE 1): RCA type 1 pair (L/R)Analog input (LINE 2): RCA type 1 pair (L/R)Analog input (LINE 3): RCA type 1 pair (L/R)Audio output terminal Subwoofer Pre Out: 10 kohmsFront speaker sectionType2-way type speaker system (Magnetic shield)5 cm (2") Tweeter 110 cm (4") Woofer 1Impedance4 ohmsGeneralDimensions Width: 1230 mm (48-7/16")Height: 476 mm (18-3/4")Depth: 397 mm (15-5-/8")Weight46.5 kg (102.3 lbs.)Glass on top of unit The maximum load/weight: 100 kg• SubwooferTypeBass reflex system16 cm (6-1/2") Woofer 1Maximum input power 150 WImpedance4 ohms• Remote controlPower sourceDC 3V ["AAA" size (UM-4, R03, HP-16 or similar) battery2]ReferencesE-40
Page 1 and 2: MODELLMODÈLEMODELOMODELLOMODELAN-P
Page 3 and 4: Når ON/STAND-BY-knappen er sat i S
Page 5 and 6: Hergestellt unter Lizenz von Dolby
Page 7: Informazioni per un corretto smalti
Page 10 and 11: AN-PR1000HENGLISHGeneral Informatio
Page 12 and 13: AN-PR1000HENGLISHControls and indic
Page 14 and 15: AN-PR1000HENGLISHGeneral Informatio
Page 16 and 17: AN-PR1000HENGLISHSystem connections
Page 18 and 19: AN-PR1000HENGLISHSystem connections
Page 20 and 21: ON/REMOTESTAND-BY TIMERSENSOR VOLUM
Page 22 and 23: AN-PR1000HENGLISHAudio connections
Page 24 and 25: AN-PR1000HENGLISHGeneral control•
Page 26 and 27: AN-PR1000HENGLISHListening to the p
Page 28 and 29: AN-PR1000HENGLISHEnjoying surround
Page 30 and 31: AN-PR1000HENGLISHBasic OperationEnj
Page 32 and 33: AN-PR1000HENGLISHListening to the r
Page 34 and 35: AN-PR1000HENGLISHUsing the Radio Da
Page 36 and 37: AN-PR1000HENGLISHUsing the Radio Da
Page 38 and 39: AN-PR1000HENGLISHTimer and sleep op
Page 40 and 41: AN-PR1000HENGLISHTimer and sleep op
Page 42 and 43: AN-PR1000HENGLISHOperating the TV o
Page 44 and 45: AN-PR1000HENGLISHAdvanced FeaturesC
Page 48 and 49: MITTEILUNG/ LE MÉMO/ EL MEMORÁNDU
Page 50 and 51: SHARP ELECTRONICS (Europe) GmbHSonn

AN-PR1000H Operation-Manual GB - Sharp

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?