Series SYJ3000/5000/7000 - SMC Pneumatics (Ireland)

For details about certified productsconforming to international standards,visit us at www.smcworld.com.44/5 Port Solenoid ValveRubber SealSeries SYJ3000SpecificationsJIS Symbol5 port 4 port (manifold)2 position single(B)(A)2 43 1 5(R)(P)(R)2 position double(B)(A)2 43 1 5(R)(P)(R)3 position closed center(B)(A)2 43 1 5(R)(P)(R)3 position exhaust center(B)(A)2 43 1 5(R)(P)(R)2 position single(B)2 (A)41 3(P)(R)2 position double(B)2 (A)41(P)(R)33 position closed center(B)2 (A)41(P)(R)33 position exhaust center(B)2 (A)41(P)(R)33 position pressure center 3 position pressure center(B)(A)(B)2 42 (A)43 1 5(R)(P)(R)Body portedBase mounted1(P)(R)3Fluid2 position singleOperating pressure rangeMPa2 position double3 positionAmbient and fluid temperature (°C)Note 1)Response time (ms)2 position single, double(at 0.5 MPa)3 positionMax. operating2 position single, doublefrequency (Hz)3 positionManual override (Manual operation)Pilot exhaust methodLubricationMounting orientationShock/Vibration resistance (m/s 2 Note 2))EnclosureSolenoid SpecificationsElectrical entryCoil rated voltage (V)Allowable voltage fluctuationPower consumption (W)Apparent power VA ∗Bracket MountingDCAC 50 /60 HzDCStandardWith power saving circuit100 V110 V[115 V]AC200 V220 V[230 V]Air0.15 to 0.70.1 to 0.70.2 to 0.7–10 to 50 (No freezing. Refer to page 1-7-4.)15 or less30 or less103Non-locking push type, push-turn locking slotted type, push-turn locking lever typeIndividual exhaust for the pilot valve, common exhaust for the pilot and main valveNot requiredUnrestricted150/30Dustproof (∗ M8 connector conforms to IP65.)∗ Based on IEC529Note 1) Based on dynamic performance test, JIS B 8375-1981. (Coil temperature: 20°C, at rated voltage)Note 2) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axialdirection and at the right angles to the main valve and armature in bothenergized and de-energized states every once for each condition.(Value in the initial state)Vibration resistance: No malfunction occurred in one sweep test between 45 and 2000 Hz. Testwas performed to axis and right angle directions of the main valve when pilotsignal is ON and OFF. (Value in the initial state)Grommet (G), (H), L plug connector (L),M plug connector (M), M8 connector (W)24, 12, 6, 5, 3100, 110, 200, 220±10% of rated voltage0.35 (With indicator light: 0.4)0.1 (With indicator light only)1.4 (With indicator light: 1.5)1.6 (With indicator light: 1.7)[1.7 (With indicator light: 1.8)]2.3 (With indicator light: 2.4)2.5 (With indicator light: 2.6)[2.7 (With indicator light: 2.8)]Surge voltage suppressorDiode (Non-polarity type: valistor)Indicator lightLED∗ In common between 110 VAC and 115 VAC, and between 220 VAC and 230 VAC.∗ For 115 VDC and 230 VDC, the allowable voltage is –15% to +5% of rated voltage.q Insert the lower hook of the mounting bracket intothe groove on the bottom of the valve as shown.w Press the valve and mounting bracket togetheruntil the upper hook of the bracket snaps intoplace in the groove on top of the valve.Made to Order Specifications(For details, refer to page 1-5-72.)1-5-4