Compool to EasyTouch Upgrade Manual Rev B 03-15-2010 - Pentair
Compool to EasyTouch Upgrade Manual Rev B 03-15-2010 - Pentair
Compool to EasyTouch Upgrade Manual Rev B 03-15-2010 - Pentair
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
IMPORTANT INFORMATIONHow <strong>to</strong> change your <strong>Compool</strong>/<strong>EasyTouch</strong> <strong>Upgrade</strong>system <strong>to</strong> a “Single Body” systemConfiguring <strong>Compool</strong>/<strong>EasyTouch</strong> as a SINGLE BODY SYSTEMThe <strong>Compool</strong> <strong>EasyTouch</strong> <strong>Upgrade</strong> circuit board is fac<strong>to</strong>ry configured and ready <strong>to</strong> operate as aSHARED EQUIPMENT system (Jumper J25 = ON). To change the <strong>Compool</strong> <strong>EasyTouch</strong> <strong>Upgrade</strong> board<strong>to</strong> operate a SINGLE BODY system, first remove Jumper 25 (place the jumper on one of the pins) anderase the EEPROM (see page 49).To change <strong>Compool</strong> <strong>EasyTouch</strong> circuit board:Getting ThereMENU ▼ SETTINGS ▼ Erase EEPROM▲Erase EEPROM1. Write down your <strong>Compool</strong> system settings and connections (e.g. filter pump schedules,auxiliary connection for lights, spa jets etc.).2. Change system <strong>to</strong> SINGLE BODY system (jumper OFF): Remove circuit board JumperJ25. Place the jumper on one of the pins. J25 is located in the upper/center of the circuitboard (see page 76).3. Erase the circuit board EEPROM: Power up the <strong>Compool</strong> <strong>EasyTouch</strong> <strong>Upgrade</strong> circuitboard. To erase the EEPROM, press MENU > SETTINGS > Erase EEPROM and followthe screen prompts as shown below:Erase EEPROMErase ALL? No (Yes)Up/Down but<strong>to</strong>n: Select Yes.Erase EEPROMAre You Sure?No (Yes)Right but<strong>to</strong>n: The message “Erase EEPROM Are You Sure? No” isdisplayed.Up/Down but<strong>to</strong>n: Select Yes.AUTO HEATERSPA 95°F / 100°FAIR 70°FMON 09:30 AMRight but<strong>to</strong>n: Press this but<strong>to</strong>n <strong>to</strong> erase system data and res<strong>to</strong>re thefac<strong>to</strong>ry defaults. The display will go blank, then the main screen will bedisplayed.4. Continue <strong>to</strong> setup your system using the <strong>EasyTouch</strong> menu (see page 14).© <strong>2010</strong> <strong>Pentair</strong> Water Pool and Spa, Inc. All rights reserved.1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-800010951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 553-5000<strong>EasyTouch</strong>®, <strong>Compool</strong>®, IntelliChlor®, IntelliFlo®, MagicStream®, ThermalFlo®, QuickTouch®, IntelliBrite®,SAm®, SAL®, FIBERworks®, Pho<strong>to</strong>n Genera<strong>to</strong>r®, and <strong>Pentair</strong> Water Pool and Spa® are trademarks and/orregistered trademarks of <strong>Pentair</strong> Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/or other countries. Unless noted, names and brands of others that may be used in this document are not used <strong>to</strong>indicate an affiliation or endorsement between the proprie<strong>to</strong>rs of these names and brands and <strong>Pentair</strong> Water Pooland Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those parties or others.P/N 521102 - <strong>Rev</strong> B - <strong>03</strong>/<strong>15</strong>/<strong>2010</strong>
Change language