Compool to EasyTouch Upgrade Manual Rev B 03-15-2010 - Pentair

More documents

Recommendations

Info

34IntelliFlo VF parameters (Continued)BackwashClean Filt : 10Flow GPM : 60Duration : 5 Clean Filter PSI (1 - 50 psi) Default 14 PSIThe average PSI setting is between 10 PSI and 20 PSI for most pools and filters. The entered PSIvalue splits the percentage meter for the filter. When the ""clean filter"" value is reached, EasyTouchdisplays an alert message and the pump stops monitoring flow rates and starts managing pressure.The value represents the change in pressure over time from start up (system clean) to present day(system getting dirty). The changes can come from anywhere in the system, for example cloggedskimmers or pots in pumps. Setting this parameter at a lower level will cause the alert message tocome up sooner and you will have to clean your filter (cartridge) or backwash your filter (sand or DE)sooner.Backwash Flow GPM (15 - 130 GPM) Default 60 GPM.Backwash Duration (1-60 minutes) Default 5 minutes.Rinse Time (1-60 minutes) Default 1 minute.Pump VacuumFlow (gpm) : 50Time (min) : 10Vacuum Flow GPM (15-130 GPM) Default 50 GPMThis setting sets the GPM that the pool vacuum will use.Vacuum Time Mins. (1 - 600 minutes (10 hours) Default 10 minutesThis parameter can be set from 1 to 600 minutes. The typical setting is 10 minutes. This setting setsthe amount of time you wish to run the pool vacuum.GPM: 731927 RPM 1980 WFilter: 7Status: NORMAL Status screen: Displays current operating information: GPM, RPM, Filter minutes, and pumpcommunication status.Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide
35Settings Menu: IntelliChlorWhile the EasyTouch system is in normal operating mode (“Pool,” “Spa” mode or “Spa Fill (Spillway),” it willcontrol the IntelliChlor chlorine output level. The amount of chlorine introduced into the pool is determined bythe amount of salt in the water, water temperature, and the amount of time the pool pump is running in “Pool”mode. Note: While in “Freeze Protection” mode, IntelliChlor will not operate or produce chlorine during thetime that the filter pump is operating. For more information, refer to the IntelliChlor Electronic ChlorineGenerator User’s Guide (P/N 520589).IntelliChlorGetting ThereMENU ▼ SETTINGS ▼ INTELLICHLORTo setup the IntelliChlor :IntelliChlor 1/2Enable: NoLevel: 50% IntelliChlor 2/2Super Chlr: OffRun Hours: 24Right button: Enable/Disable IntelliChlor. (To select SuperChlor, run hours, press theUp/Down button - 2/2).Up/Down buttons: Select Yes or No to enable or disable IntelliChlor.Right button: POOL Mode “50%” setting.Up/Down buttons: Set the chlorination output level for the pool water from 0 to100%. EasyTouch will determine the chlorinator output level when the system isoperating in “Spa” or “Pool” mode. The amount of chlorine introduced into the pool/sap is determined by the amount of salt in the water, water temperature, and theamount of time the pool/spa operates in these modes mode.Right button: SPA Mode “0%” setting.Up/Down buttons: Set the chlorination output level for the spa water from 0 to 20%.To prevent over chlorination of the spa, the EasyTouch system will automatically dropthe chlorine output levels to 1/20th of the current pool output when the spa is switchedon. For example, if the pool output level is set to 60%, when the spa is switched on,the chlorination level is reduced to 3%.Right button: Select the next set of settings (2/2).Up/Down buttons: Select 2/2.Right button: Move the Super Chlorination settings.Up/Down buttons: Set Super Chlorination On or Off. See note below about SuperChlorination.Right button: Select “Run Hours” setting.Up/Down buttons: Set the number of hours to run Super Chlorination. 24 hours isthe default setting. Run hours can be set from 0 to 72 hours.Press the Menu button to save the settings and to return to the Settings menuoptions. Press the button again to return to the main menu options or press again toreturn to the main screen.Note: For IntelliChlor status messages, see “Diagnostics: Chlorinator” page 53.About Super Chlorination: The Super Chlorination feature is used to introduce large amounts of chlorineinto the pool water if there has been heavy rain fall, many bathers in the pool, cloudy water conditions, etc.When Super Chlorination is enabled, the system will switch on the filter pump, set the pool/spa valves to thecorrect position, and set the IntelliChlor chlorine generator to maximum output. This process continues for 24hours. At the end of the Super Chlorination process, the pool will return to normal operation. It is possible tomanually stop the Super Chlorination process and switch off the filter pump using the Filter (F) button on themain control panel at the pool equipment pad. When the filter pump is switched on again using the Filter (F)button, the Super Chlorine process will resume for the duration of time left.Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide
Page 1 and 2: UpgradeMODES OF OPERATIONAuto: Indo
Page 3 and 4: iContentsIMPORTANT SAFETY PRECAUTIO
Page 5 and 6: iiiContents (Continued)First Time S
Page 7 and 8: vIMPORTANT WARNINGS AND SAFETY PREC
Page 9 and 10: 1Section 1OverviewCompool ® EasyTo
Page 11 and 12: 3Compool EasyTouch Upgrade Control
Page 13 and 14: 5Controls and buttons (Continued)
Page 15: 7EasyTouch Indoor and Wireless Cont
Page 19 and 20: 11Schedule start and stop times for
Page 21 and 22: 13Section 2Setting up Compool/EasyT
Page 23 and 24: 15EasyTouch Menus (Continued)SETTIN
Page 25 and 26: 17Feature Circuits MenuThere are ei
Page 27 and 28: 19Setting up LightsThe following se
Page 29 and 30: 21Setting up lights (Continued)Mode
Page 31 and 32: 23Setting up MagicStream LaminarsTh
Page 33 and 34: 25Heat MenuUse the heat menu settin
Page 35 and 36: 27Schedules MenuUse the Schedules m
Page 37 and 38: 29Using the Once Only featureThe
Page 39 and 40: 31Settings Menu: ClockUse the Clock
Page 41: 33IntelliFlo VF pumpTo access the I
Page 45 and 46: 37Settings Menu: Circuit NamesLabel
Page 47 and 48: 39Settings Menu: Circuit FunctionsA
Page 49 and 50: 41Settings Menu: Custom NamesThere
Page 51 and 52: 43SolarTo enable a solar heater and
Page 53 and 54: 45Settings Menu: iS10 Spa-Side Remo
Page 55 and 56: 47Settings Menu: QuickTouch (QT4) W
Page 57 and 58: 49Settings Menu: Erase EEPROM (Eras
Page 59 and 60: 51Spa Side [Off/On]Enable or disabl
Page 61 and 62: 53Diagnostics Menu: ChlorinatorDisp
Page 63 and 64: 55Section 3TroubleshootingTroublesh
Page 65 and 66: 57Maximum Programs ExceededThe “M
Page 67 and 68: 59Problem: The Quick Touch remote w
Page 69 and 70: 61First Time System Start-UpThe fol
Page 71 and 72: 63Synchronizing control panelsIf th
Page 73 and 74: 65Section 4Compool/EasyTouch Upgrad
Page 75 and 76: 67Shared EquipmentSystemsC OMPOOLEA
Page 77 and 78: Other remote devices are disabled.t
Page 79 and 80: 71To install the Compool/EasyTouch
Page 81 and 82: 73Remove (3)screwsRemoval of Compoo
Page 83 and 84: 75Switch the main AC power OFF to t
Page 85 and 86: 77VA LV E MODU LE(optional)VLV1WITH
Page 87 and 88: NOTES

Compool to EasyTouch Upgrade Manual Rev B 03-15-2010 - Pentair

Create successful ePaper yourself

Delete template?

Save as template?