Manual - Unvented Gas Log Heater or Vented Decorative Appliance

More documents

Recommendations

Info

DEB Unvented Gas LogsINSTALLATIONWARNINGConnecting directly to an unregulatedp r o p a n e / L P G t a n k c a n c a u s e a nexplosion.CHECK GAS PRESSUREThe heater gas inlet connection is a 3/8" NPT at the valve.On all control type units, the inlet connection is on the rightside of unit. To connect from the opposite side, route thepipe around the back portion of the unit.When tightening up the joint to the valve, hold the valvesecurely to prevent movement.Test all gas joints from the gas meter to the heater valvefor leaks using a gas analyzer or soap and water solutionafter completing connection. DO NOT USE AN OPENFLAME.Check the gas pressure with the appliance burning andthe control set to HIGH.Manual ControlFigure 16The pressure regulator is preset and locked to discouragetampering. If the pressure is not as specified,replace the regulator with the correct part from the partslist in this manual.Remove 1/8" NPT plug, located on side of regulator body.Install fitting and tubing to pressure gauge. After takingpressure reading, reinstall test plug. Check for gas leaks.Millivolt ControlFigure 17The valve regulator controls the burner pressure whichshould be checked at the pressure test point.Turn captured screw counter clockwise two or thre turnsand then place tubing to pressure gauge over test point(Use test point “OUT” closest to control knob). After takingpressure reading, be sure and turn captured screw clockwisefirmly to re-seal. Do not over torque. Check for gasleaks.Test Port “Out”Figure 17 -Millivolt Control PressureTest Point LocationFP2372millivolt valveFP2372NPT Test PlugFigure 16 -Manual Control PressureTest Point LocationFP2499manual valveFP249914 44D0060
ELECTRICAL WIRING - MILLIVOLTDEB Unvented Gas LogsWARNINGLabel all wires prior to disconnection when servicing controls.Wiring errors can cause improper and dangerous operation.Verify proper operation after servicing.ODS PilotOn/OffSwitchODS PilotWallSwitchMillivoltValveOn/Off SwitchSpade TerminalTH = 3TP = 1TP/TH = 2SwitchFP2112Figure 18 -Wiring DiagramThe millivolt valve is a self-powered combination gas controlthat does not require 110 Vac to operate.Connect Optional Wall Switch orThermostat1. Use 18 awg, two-wire cable, 15 feet maximum length.2. At one end of the cable, connect both wires to the wallswitch or thermostat. At the other end, connect onewire to TP/TH and one wire to TH, or connect the wallswitch/thermostat to the two male (0.25") terminals onthe left side of the unit. The color of the wires does notmatter.FP2112wiring diagram12/08Optional WallSwitch, RemoteReceiver orOptional T-Stat44D0060 15
Page 1 and 2: Unvented Gas Log Heateror Vented De
Page 3 and 4: IMPORTANT SAFETY INFORMATIONINSTALL
Page 6 and 7: DEB Unvented Gas LogsGETTING STARTE
Page 8 and 9: DEB Unvented Gas LogsFIREPLACE and
Page 10 and 11: DEB Unvented Gas LogsINSTALLATION R
Page 12 and 13: DEB Unvented Gas LogsBefore fully i
Page 16 and 17: 26D331726D3317DEB Unvented Gas Logs
Page 18 and 19: DEB Unvented Gas LogsELECTRICAL WIR
Page 20 and 21: DEB Unvented Gas LogsLOG PLACEMENTL
Page 22 and 23: DEB Unvented Gas LogsFLAME APPEARAN
Page 24 and 25: DEB Unvented Gas LogsOPERATING INST
Page 26 and 27: DEB Unvented Gas LogsOPERATING INST
Page 28 and 29: DEB Unvented Gas LogsTROUBLESHOOTIN
Page 30 and 31: DEB Unvented Gas LogsREPLACEMENT PA
Page 32 and 33: DEB Unvented Gas LogsREPLACEMENT PA
Page 34 and 35: Massachusetts DEB Unvented Gas Logs
Page 36: MHSC149 Cleveland Drive • Paris,

Manual - Unvented Gas Log Heater or Vented Decorative Appliance

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?